Having problems with your Bissell Vacuums ?
Bissell easyvac Roller Lifter Assembly out of place
\015 I went over a metal lip on my floor a little too hard and now the "lift roller assembly" is out of place making a lot of noise and causing the whole vacuum to sit off balance. can i pop it back in or did i break it?\015
Repair Help & Product Troubleshooting for Bissell Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Bissell easyvac Roller Lifter Assembly out of place
... Bissell Vacuums
Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus
... Bissell 6595 Lift Off Bagless Upright Vacuum
Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!
Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
I have a Bissell Pro Heat Power Lifter Cleaner. The float bar in the tank assembly has come out and I can't figure out how to put it back in. I can't find a picture of the assembly to see how it fits. thx val
... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
Where is model number on bissell proheat - Bissell Proheat Upright Carpet Cleaner Roller Brush Assembly With End Caps 210-1128 - Genuine
... Bissell Proheat Upright Carpet Cleaner Roller Brush Assembly With End Caps 210-1128 - Genuine
I have misplaced the instructions for assembling and using the Bissell Pro dry TLP Power Roller that I purchased some time ago from HSN. Need to use it now.
Here is a link to three different models. please find the model # on your unit. \015\012\015\012\015\012 ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum
The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th
... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum
Bissell roller question
You need to replace the brush roll, part #\015\012\015\012\015\012\015\0122032013, \015\012I would also put a new belt on as well, 2031093, style 7 belt.\015\012Most vacuum repair shops should have these or can get them for you. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum
Bissell Lift Off Broken Belt and Brush Roller
I had the same problem. I found that the brush actually melted to the end cap (the one with the square/ovalish end). I was able to pull it off with some force and applied some WD-40, but that only worked for one more use. The brush has again melted t ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.
Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum
I need a "Bearing Assembly" for roller brush 61445-1,I Have a GE 106575
Probably should just go to a repair shop and they should be able to order one for you, that is if they are available by themselfs. Or if you have a store where you live that sells vacuum parts, you could go there. ... GE 106585 Upright Vacuum
Riccar model rad.7 upright (radiance). roller brush won't turn and red roller brush indicator is on. roller will turn easily by hand and belt is in place. how do i fix this?
As you already know, the red brush indicator light indicates that the brush roll has stopped turning, usually because an object has become stuck in the brush roll. When that happens you should turn the machine off (unplug it also for safety), remove ... Riccar 8955 Upright Vacuum
DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>
I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.
... Hoover Tempo Widepath Upright Vacuum - Blue
Bissell Lift OfF Brush Roller Stops Rotating
They make the worst machines, the rollers are cheap and they make it so you cant take them apart to clean them. You don't want a dyson either, they aren't any better for pets. With all that hardwood floors you should get a good canister vacuum, sebo ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum
I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......firstname.lastname@example.org
You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum
What is belt part number foe bissell 3108 - Bissell 3108 EasyVac Powerbrush Upright Vacuum
The drive belt part number is 210-0130 for the bissell 3108. The number for bissell consumer services is 1-800-237-7691, hope this helps!! ... Bissell 3108 EasyVac Powerbrush Upright Vacuum
Need new belt 210-0130, bissell easy vac - Bissell 3108 EasyVac Powerbrush Upright Vacuum
... Bissell 3108 EasyVac Powerbrush Upright Vacuum
My full size bissell sprayed the room just fine, but now it won't **** up the water. Help! The container is closed and locked into place, and the bissell sounds fine.
Wish you had provided the model number, as they are different. The most common, if there is a flow indictor, is the filter there clean or clogged. The other possilbe, there is a ovule black seal that sits on top of the clear window noozle and the e ... Vacuums
Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the
Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums
I REMOVED THE PLATE THAT IS OVER THE ROLLER TO CLEAN THE ROLLER OF HAIR AND NOW I CAN'T GET THE PLATE BACK ON AND TO SNAP INTO PLACE
If you go to this URL:\015\012\015\012http://media.dyson.com/downloads/us/floorcare/manuals/dc17_opmanual_usa.pdf\015\012\015\012you can see a diagram on how they suggest to take the plate off and clean the unit.\015\012I hope this will o ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Bissel 3670-2 brush -roller dose not rotate at all even after I ttry to pull the belt. Could someone please explain the "mechnis or the principles how the brsu roller works?
... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum
Bissell vacuum roller will not spin - Bissell CleanView II Plus Upright Bagless VacuumVacuum
HI,\015\012Most of the time if the roller will not turn it is because the belt is either strecthed too far and is loose or it is completely broken...\015\012Check and replace the belt before doing anything else.\015\012\015\01 ... Bissell CleanView II Plus Upright Bagless VacuumVacuum
FILLING INSTRUCTIONS. I HAVE A BISSELL PROHEAT PLUS 12 AMP CLEANER. HAVE LOST MY MANUAL. NEED INFO ON FILLING THE MACHINE. DO I MIX THE BISSELL CLEANING SOLUTION WITH THE WATER? IS THERE A SEPERATE PLACE TO PUT THE CLEANING SOLUTION, IF SO HOW MUCH SOLUTION PER WATER CONTENT. THANKS
Hi,Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum
My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.
Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum