Having problems with your Bissell Vacuums ?

I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the

\015 When i put it back together i noticed that one side of the bar is circle, and the other side is more oval/squared edges. It fits nicley back together, but will not spin. it goesa quarter of a spin until it gets lodged on its own hole... im not sure if their is an attachment that im missing to help it not get lodged. seems like a square spinning in a circle. Just illogical. Please help\015

Answers :

Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. http://www.bissell.com/service-centers/?cid=ccsocial

Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a bissell powerforce bagless turbo. The problem is the brush bar is not spinning. I have cleaned out all the debris on the brush itself, and taken it apart to make sure nothing is blocking the

Sorry to hear you're having difficulty with your vacuum. You may want to have a Qualified Technician at a BISSELL Authorized Service Center inspect your vacuum. Here's a quick link to locating a Service Center. ... Bissell Vacuums

I have a hoover savvy that the rollers wont turn. I've taken it apart to make sure the brushes are not caught but nothing happens. I only used this vacuum once. It was a floor model when purchased. I just need to figure out what I need to do to get this to work.

Hi there SmartAlec from NelsonVacuums.com.au here. I have to say that if it is not as simple as a belt - I assume that when you checked that the brushes weren't caught that ... Hoover U8125-900 Savvy Bagged Upright Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?

As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

My Hoover Whisper Cyclonic is collecting the dirt but not taking it into the cylinder. The brushes were at one point starting and stoping due to the belt periodically turning,now the brushes are turning and the dirt just collects and I'm starting to smell a an oder like rubber burning.I've taken it apart and tried to make sure the is no clog. The one hose that I can't check is in the back right base, above and left of the right back wheel.

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.

I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Hoover Steam Vac All Terran floor shampooer, I have taken apart the brushes and other parts to make sure there are no clogs, but it still is not spinning. What else can I do? the Motor is working fine. and the suction is fine too.

There may be some substances such as dust or sand stuck in the spinning parts of the wheel. The substances are restricting the mechanism to work properly and causing blockage in the rotating causing your problem. Cleaning every part of the motor's ro ... Vacuums

My Hoover SteamVac F5915-900 will not pick up water. I've taken the resavor off several times trying to make sure nothing is under it's lid and replaced it as instructed. I don't know wh


The roller-brush on my Dyson DC17 makes a terrible noise at all times. I removed the cover and extracted all debris from this area, making sure all connections were as secure as possible, but that didn't improve it any. The vacuum still seems to vacuum okay, but the noise sounds horrendous. How do I fix it?

Check the belt to see if a layer or piece of it has come loose and is flappping around.\015\012Check for any loose parts that could be getting hit by the brush or other moving parts.\015\012Make sure the brush it tightly in place and can ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Roomba goes in a circle moves about 5 inches and then turns in a circle again. It won't dock or go any farther than a few inches before turning in a circle again. The roomba has been cleaned inside and out. All hair and debri as been taken out of the wheels and brushes. i opened the case and cleared all the debri and i dusted the sensors in the front. Not sure what to do now.

... iRobot Roomba 550 Vacuum


It could be that you need to replace the belt. Here is the belt you need:Dyson DC07 Belts and Manual ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My hoover model #u6436-900 brush will not spin. I have changed both belts and still nothing. I even checked to make sure they were the right sizes.

Greetings,\015\012\015\012It maybe that the belts were not installed properly, or that the roller brush might be as well. Here's a good video that explains the proper procedure of how to replace the belts on your vacuum cleaner, as well ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga

I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

My daughter pulled to hard on the ceiling fan pulling out the chain. i have taken it off and apart, nothing appears to be broken but im trying to figure out how to put it together so it retracks, i assume it has something to do with the tension of the small spring inside of it, but not sure how to put it back together im wondering if there is a internal diagram of this ???

Don't even bother to repair the pull chain switch, get a new one at KMart, HomeDepot or similar store for less than $2.\012\012Two times I've repaired one, it comes apart when I need it the most.\012\012Good Day! Don't forget to rate thi ... Vacuums

My Vaccuum Hoover U5763-900 wind tunnel Twin Chamber is barely used. Belt is in tact and agitator is not worn. Nothing clogged. Agitator spins fine off the ground or on hard surface or flat rug. Once on carpet, the agitator won't spin. Not sure why. I have taken it apart over and over again.

... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The hose vacumn is not picking up right---I have taken the hose apart---nothing blocking it, but there is something clogging it up close to the collection bag---how do I access this area?

You are correct. There's something clogging between the hose and the collection bag. However, you may need to provide me the brand and exact model of your vacuum, so that I could check the assembly.Thank you! ... Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

My Vaccuum is barely used. Belt is in tact and agitator is not worn. Nothing clogged. Agitator spins fine off the ground or on hard surface or flat rug. Once on carpet, the agitator won't spin. Not sure why. I have taken it apart over and over again.

Vacuum height is set too low, jamming the brush ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.

Squealing ... Vacuums

No suction I live in a house with two bernese mountain dogs... very large animals who shed a LOT.  I've cleaned the filters, the roller, and gotten as far into the hoses as I can without taking the entire machine apart.  It's still not cleaning as well as I know it can... nothing is making it into the debris receptacle.  What can I do?

Hi elora,\015\012\015\012I live in a house with three shedding cats. I also have the same vacuum. About twice a year, I have to getinto the area of the vacuum where the motor is. There is a little pring loaded vavle that sometimes gets ... Bissell 3590 CleanView Bagless Upright Vacuum

My brush is no longer working on my bissell healthy home vac. when i try to turn it on it makes a high pitched squealing sound. I'm pretty sure it needs a new belt but my husband is having trouble getting the vac. apart. He says you need a special tool to get the screws out of the bottom of the vac. Any advice? THANK YOU!

Hi,\015\012 According to Bissel, they should be standard phillips screws. Nowever - things change.\015\012This is a general guide from Bissel for belt change - \015\012 ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

My roomba 550 makes loud clicking noises and stops after 5 minutes and tells me to check brushes. I have taken it apart as much as possible and cannot find the problem

Pull brush rollers out.pull funny lookin yellow ends off and clean hair ect.out .also pop out front wheel and clean ... iRobot Roomba 550 Vacuum

My Animal Dyson (the purple one) is making strange noises. The ball will not roll. I've taken it apart and put back together and it works for a couple minutes and then it won't work again I think it's Model DC24 or 25. Pretty sure its 24.

... Dyson Ball DC24 Bagless Upright Vacuum

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My Dyson DC 14 is making the horrible "ratcheting"sound only when the brush is engaged on the carpet setting. I have cleaned the brush, so there are no obstructions, the canister is empty and properly on the unit. I checked to make sure all of the "traps" and hoses are clear of obstructions, the belt is on the brush securely and moves freely, the brush itself spins freely, but there is still the "ratcheting" noise. Any other suggestions?

Our DC33 was making the same ratcheting sound immediately upon placing the cleaner/brush head on the carpet. We carefully pulled the beater/brush bar out of the vacuum. Once removed, we pulled the black plastic end off of the center rod. We discovere ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hoover 5470-900 no longer contacts carpet with beater brush

Your floor adjustment spring is broken there is a plastic slider and clip if it is broken the height adj will not work you should get a new vacuum because this repair can cost as much as a new vac.also this is a common problem with the hoover brand I ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0975 seconds