Having problems with your Bissell Vacuums ?

Our Bissell vaccum turns on and sounds normal but it is not sucking anything up the hose.


Answers :

Check and clean all filters or look for any obstruction in the hose.
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our Bissell vaccum turns on and sounds normal but it is not sucking anything up the hose.


Check and clean all filters or look for any obstruction in the hose. ... Bissell Vacuums

My bissell 82h1 has developed a very loud clattering noise. I cleaned the brushes and checked everything I could easily access to no avail. When I turn it on with the brush removed, the sound level is normal. With the brush in place, I can easily turn it by hand with no indication of it hitting anything.


... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum

When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!


Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Rotating bruch My vaccum brush will not turn. This happened after sucking up a cord that wrapped arou8nd the brush. I was able to pull the cord back out but now the brush will not turn. The vaccum does turn on an sounds like it is working with no soinning brush.


Take off the bottom cover where the roller brush is a few screws should be all it takes underneath cover should be roller and belt if belt is broke replace it lift up roller there is a slot for the belt to run in put other end should be the motor sid ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

Dyson dc41 wont suck up on hose and hose pulls back when turned on


... Dyson Bagless Upright Vacuum DC41 Animal

Went to turn it on after not using for several weeks and it states not ready to brew like usual but after about four minutes it just turns off. Wont let us brew a cup or access the menu even to choose size of cup or anything. It sounds like it's sucking up water to make cup and pokes hole in the coffee but nothing more than that. It is almost brand new


You have posted the fault in the wrong column with no instruction of the make/model.\012Assuming it to be new , Is it passed the warranty period before we take a look ,?\012Just lave it on for sometime and see if there is any change. per ... Vacuums

I bought a Kenmore canister vacuum, model 116, in April 2007. This morning, the sound of the motor suddenly began to deepen, and I began to lose suction. Normally, if something is clogging the hose, the motor will wind up to a higher pitch, not a lower one. The filters are clean, the bag is empty, and I can't detect anything lodged in the hose. If this were a car's engine, I would say it's "lugging down". Any pointers?


Okay, bear with me. Is it possible you have a suction adjustment, dial somewhere on vac. Check and see and if it does, be sure it's all the way up. Also, try removing hose and run a broom handle fr. one end to the other...BUT be careful not to stretc ... Vacuums

I have a bissell proheat multi surface 2x model 9200-T 08296C. It stopped spitting the water and soap out on the floor, but still sucks from the base and hose. I took it apart to see if anything was disconnected but saw nothing. Please help!


I Had the same problem with my model 79011...take the upright handle apart & you will see a pot-metal rectangular box midway down the lower section of the handle with wires on it & 2 hoses attached. This is the water heater unit. LET IT COOL ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My vaccum turns on and sounds normal, however I have no suction. I snaked the pipes and it wouls appear that there is nothing clogiing the lines


See if the drive belt is attached or broken. ... Broan-NuTone VX550 Bagged Central System Vacuum

Dyson all floor vaccum no suction when hand held wand is turned on... doubled checked for cracks in hose -- none took house off unit to check for blockage --- none.. suction works fine when using as normal on floors.


You need to replace the belt that drives the brush on the underneath side of the vacuum. To do this, you need to flip the vacuum over and remove cover plate. There you will find the broken, or stretched out belt. Remove the brush and place the new be ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My Eureka Endeavor NLS is about a year old and stopped working. It just blows dirt everywhere when turned on. There is some suction to the hose part but only when it is flush against your hand or floor.Other than that, it will not suck anything up.


... Vacuums

My eureka surfacemax 300 is not sucking up anything and i have cleaned out the hose plus i turns off by itself sometimes


I've found that some times if you let the cup get too full, stuff will get jammed up above it. Turn off the vacuum and unplug it, and remove the cup. Reach up inside the vacuum above the cup and there is a small, plastic cylinder you can twist to r ... Vacuums

Hi i have a dyson animal allergy and lately when i turn its normal for about 3 seconds and then it makes a large sucking sound its still working ok.but not lifting up as good.its about 5 years old now.any ideas please.


Hello :1: Check that the Dyson's brushbar knob is turned to the "Carpets" setting \015\012for vacuuming non-delicate and raised pile carpet. Vacuuming carpet on \015\012the "Bare floor" setting usually leaves a telltale ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

I HAVE A BISSELL CLEAN VIEW HELIX, THAT RECENTLY STARTED SOUNDING FUNNY AND ALSO HAS VERY POOR SUCTION IT IS NOT PULLING ANYTHING INTO THE CONTAINER NOW FROM THE CARPET OR THE HOSE. WHAT DO I DO?


The hose is clogged or the belt is broken ... Vacuums

My bissell vacuum attachments wont work, as soon as i attach anything besides the crevice tool it wont ****,but sucks fine when its just the hose


Tern upside down remove plastic cuvier look wear the hose gos fillip skew driver ... Bissell 6594 PowerForce Bagless Upright Vacuum

I bought this vaccuum just a few months ago. Now it barely sucks anything up and it is making this very loud noise. It almost sounds like the brush is going to vibrate off. I keep thinking something is stuck in it, but I took it apart and everything seems normal. It did melt a couple of belts also.


Probably the motor is jammed or the part where it sucks up stuff its full ... Bissell 3590 CleanView Bagless Upright Vacuum

Vaccum not turning or sucking


Hello,It definitely sounds like your belt is broken. If something gets vacuumed up into the brushes, and prevents the brushes from spinning, the motor will continue to try and spin the belt and the brush, but since the brushes can't spi ... Hoover Tempo Widepath Upright Vacuum - Blue

I have a Hoover linx cordless stick vac. I have not had it but several months and it has quit sucking anything up. It worked great when I first got it. I was so excited at how well it worked. It had gotten hair wrapped around the brushes but I got that out and thought it would work better. It is turning and sounds like it is working but it does not pick it up. I could use your help please. Keely


... Hoover Platinum LiNX Cordless Stick Vacuum

The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda


You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron


The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Rollar is not turning. Belt seems to have tension. Does not **** anything up off of the floor. Filters are clean but when we turn it on, the roller is not turning or sucking anything up off the floor.


Hi Susan,I'm sorry to hear you're having difficulties with your DC07. It's probably best if you get in touch with us directly so we can determine which model of DC07 you have, and run through some troubleshooting over the phone with you. You ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller wont turn on my bissell vaccum model 5770


... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.


I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0802 seconds