Having problems with your Bissell Vacuums ?

I have a Bissell Proheat model 7901. When I pull the trigger on the handle, there is no water flow. The brushe revolves and the unit vacuums any water spilled on the floor. Could it be a failed pump or kink hose or ? Thanks Zap

Answers :

Take the handle apart and put spring back into place.
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bissell Proheat model 7901. When I pull the trigger on the handle, there is no water flow. The brushe revolves and the unit vacuums any water spilled on the floor. Could it be a failed pump or kink hose or ? Thanks Zap

Take the handle apart and put spring back into place. ... Bissell Vacuums

I have a tear in the hose of my old model # F6030-900 unit which doesn.t allow water from the attachment to **** back into dirty water bucket. The model #F6039-900 is the same model # but different year I understand. The tear is at the bottom where set the recovery tank in the lay down position and can look in the unit at the bend of the hose.

You will have to replace the hose asm. You can order online at: \015\012http://vacuumsuperstore.com/F6019.html\015\012\015\012H-90001334 (43 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Bissell 37604 Bagless Upright Vacuum. Hose keeps clogging every time I vacuum. Is there a way to prevent this? I am ready to buy a new vacuum, but it does do a great job picking up hair...until it clogs. It clogs at top of hose. Could the hose be kinked? It does not look like it.

That is a defect in the design of that style of vacuum. I went back to my old vac because I got so tired of having to unstop it. The sharp turns in the hose and the molded plastic causes it. Find one without the turns. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

The hose is disconnected, new bag in unit, new filter, unit runs when hose is detached but immediately turns off when hose is attached but hose has no obstruction, etc.. i was told i need some sort of valve. HELP! I have birds, a cat and 2 large dogs and no vacuum :)

There is a vacuum hose that attaches inside the unit to a round clear plactic piece. In most cases you can simply cut the small vacuum hose and it will fix the problem. ... Electrolux Epic 3500 Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.

... Craftsman Vacuums

Vacuum does not soak up dirt water. Fresh tap water just spilled o

... Eureka Atlantis 2591A Upright Steam Vacuum

My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?

Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve

HelloGrasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually insp ... Vacuums

We have a Bissell Proheat 2X (model 8920). The problem we are having is when water/soap is initially released (all settings) it continues to leak out the front water spray nozzles unit the water containers are empty. The vacuum works but can't keep up with the continuous water leaking out. Do you have any idea what is sticking open to allow the continued release of water when the machine is running? Thanks Rick

Return it. It is faulty and should not do that. Mine does not. Does require changing water about evrery 10 minutes but one can see the filth in the water. Also re-clean with plain water over areas that were cleaned to remove all cleaner. Old cleaner ... Bissell 8920 ProHeat 2XTM Upright Vacuum

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.

I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Kenmoore Intellivac w direct drive suddenly started making internal sound like something was stuck. Hose is clear, and sound is made when hose is detached from main unit. Vacuum sounds find at lower pressure, only makes sound with bag door closed and/or placing my hand over the end of hose.

Shut off the vac and open container and remove the bag. Try dropping a coin into the hose, then raise up to see if it falls thru to the bag area. If it does check the throat of the vac where the dirt is sucked upward to dump into the bag itself. ... Kenmore 35912 / 35913 Progressive Upright Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth

When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I

Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

Central vacuum Hello, my central vacuum motor just clicks when you insert the hose into the receptacle. Is there anything I can do besides get a new motor or unit?

If the central vacuum is clicking that means that the circuit breaker is working and trying to get the motor to run but the motor is not functioning. This means it's time for either a new motor or a new unit. Unfortunately there's really no way aroun ... Electrolux Central Vacuum

Do i need a special hose to vacuum up water? - Rainbow E series Canister Wet/Dry Vacuum

Yes. You need a non-corded hose so there is no power running through it when vacuuming up liquids. ... Rainbow E series Canister Wet/Dry Vacuum

My bissell powersteamer model 1695 does not spray enough water out. Hardly anything will come out of the handheld attachment either, just a few drips. With the floor unit, it appears the only water coming out is a result of gravity when the control is squeezed. Nothing appears to be plugged up with debrie or deposits. There does not appear to be any kind of drive belt for the pump as it seems to operate off the main vacuum motor. Any ideas?

Hi, my name is John I will do my best to assist you.\015\012\015\012Referring to this ... Bissell 1695 PowerSteamer Vacuum

I have a used Bissell proheat pet machine with no users manual. It will not extract water. In fact it blows air out instead of vacuuming. I checked the belt it is fine. All hoses looked good too. It has no vacuuming with the attachments either. Help. Betzi

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

I took the hose off to wash it then after letting it dry overnight I put it back on but Im guessing it there was still a little bit of water in between the grooves which ran to bottom of vacuum and now my dyson gets stuck, sort of like a tight hinge. It vacuums fine but I have to keep pushing it down to the carpet with my foot. How can I fix this problem?

Lubrication at the pivot points ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Theres wet food stuck in the hose of the vacuum its a hoover fusion model U5180-900 and I was wondering if you can **** up water to get the hose clean

Hi there smartAlec from nelsonVacuums.com.au here. The answer is NO ! Any moisture you **** up will certainly end in the motor which will ruin your vacuum. If your can remo ... Hoover U5180-900 Vacuum

1993 chevy silverado 1500 fails emission and has error code of 32 this refers to EGR issue but i need a vacuum diagram to figure out if any hoses are missing has anyone had any dealing with egr fail code?

... Vacuums

I have an easy flo vacuum model # 199C and it won't shut off. It started out as an intermitent problem but now will not shut off when the hose is unplugged, nor when the off/on switch on the main unit is shut off. the only way to get the motor to stop running is to unplug the unit. Any ideas?

Just had this same problem. I unplugged the low voltage signal wires and the vacuum stayed on. Thus eliminating the possibility of the signal wires shorting out somewhere. I'm not really sure which wire(s) were causing the problem. But when I disasse ... Easy Flo EF1500 Vacuum

I have a proheat 2x, and the pump will only spray water for a few seconds when unit is turned on, then nothing. The attachment is the same way. I think this is the pump failing, and the unit is only over a year old. How much would a pump cost? If this is the problem.

I just had my pump replaced for $66 and the repairman said this unit is notorious for this problem. He had 6 other units in his shop when we came in. Make sure you keep your clean water tank FULL, as he said the pump fails as soon as it runs dry. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1376 seconds