Having problems with your Bissell Vacuums ?

Proheat Protech will not spray liquid. I have re-seated everything, checked filters, belt. The nearest service is over 50 miles away.


Answers :

Hopefully this solution is for the model you have:
\015\012
\015\012
Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be on the tank, not in the hole, this is for the soap bottle also, there is a seal on the bottom of it as well. The flow indictor cap is leaking air or maybe is too tight. If you had the top cover off, make sure that the tubes are routed right so as not to get pinched when the cover is put back on, the smart mix knob should be in the water setting and that the piston is on the bottom of the smart mix knob. Pump is bad. Try running a mix of vinegar and water to see if that unclogs the lines. Is the top cover and the base tight together in the back, sometimes the top breaks loose and it will raise up and it can't spray, just re-fasten it down.
Repair Help & Product Troubleshooting for Bissell Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Proheat Protech will not spray liquid. I have re-seated everything, checked filters, belt. The nearest service is over 50 miles away.


Hopefully this solution is for the model you have:\015\012\015\012Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If ... Bissell Vacuums

Relief valve opens I have cleaned all filters replaced filters checked all hose line for blockage everything is clear


How full is the bag? ... Kenmore Vacuums

My DC17 is only a few months old, but I've already had to clean the filter. Since I reassembled everything, I'm finding chunks of carpet fiber and dog fur on top of the filter inside the filter container. Iam getting slightly less suction from the floor assembly as well. I've checked the hoses, brush, and brushed out the inside of the plastic container, but hasn't helped. Ideas??


Everyone needs to own an air compressor,\015\012if you own a bagless vacuum\015\012\015\012You blow it out every other time you use it.\015\012\015\012Without compressed air, all vacuums will just\015\012basically ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Using my unit (owned about 6 years - great service so far) it suddenly quit ... no wind down or 'prelude' like whine - growl - etc. -- it just quit running ... suggestions? clear filters? done check power? how check power cord? done help ...


I agree with you having great service because mine only lasted two years. It sounds like the motor just worn out. If you don't smell any burnt electrical then replace the bushing for the motor. Good Luck ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

I have a Bissell proheat 2x microban carpet cleaner. no water is dispensing . I have tried double cleaning everything, changing soulation(bissell steam clening) checking the filters checking for hot water, the brushes turn (belt?) What should I do?,


... Bissell Vacuums

I have a Tetratec IN600 Plus aquarium filter which does not seem to be pumping air bubbles through the water. I have checked inside and everything looks as if it should work. The pump system seems to be working as the filter is vibrating when on, but no bubbles! Please help!


... Tetra Vacuums

I have a new Kenmore vacuum cleaner w/power head also Hepa Filter. The power head started once and will not start now. I have checked to make everything is hooked up right. The reset button is below


... Vacuums

The hose has no suction and shrinks up so that it can't even be put back on the vacuum w/o turning it off. I have checked everything that I can think of and don't see any blockage anywhere. I washed the filter about one month ago and I clear it at least once a week.


Just happened to me. Took everything apart. No blockage in the flexable tubing or connections then I looked down the hard, telescoping tube and saw that it was occluded. Everything's fine and dandy now. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

NO SUCTION My Electrolux Z2274 upright vacuum cleaner has lost it's suction and is very noisy. Have checked and rechecked there is no blockage. Have cleaned the filters. In fact done everything I can think of. Any one know why and how to fix this??


If you have no suction, there are only a couple of things that could cause it. As you have checked for blockage, and changed your filters, you may have a vacuum motor with bad bearings, or broken fan blades (inside/on the vacuum motor). Either sympto ... Electrolux Central Vacuum

DYSON DC05 It just doesnt want to turn on. I switched it off, one minute later I tried to switch it back on and it didnt work. I have washed the filters, checked the tubes and everything seems ok.......any ideas? thank you, Lucie


My friends Dyson DC05 was loosing suction and then it stopped altogether one day. When she took the filters out there was black soot in them so it was obvious that the motor had burnt out. I think this happened because she wasn't cleaning the filters ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have a mile tt2000 that works fine up to 1300W but if I crank it up higher the motor decreases and increases speed every couple of seconds. I have changed the bag and filters and done the usual cheCks for blockages but can find nothing amiss. Unusually when it is running and I block the intake it will run at full power but as soon as I clear it the motor "hunts" again. Any ideas.


... Miele Cat & Dog 326i Bagged Canister Vacuum

Bissell 5770 Healthy Home vacuum fell over and now will not power on. Closest service center is 55 miles away. I'm very hands and can fix most things, but never took apart a vacuum yet. Can I do this?


Same thing happened to me. The handle connects to the unit and actually plugs in. If you are lifting or carrying it by the handle then you can unplug the unit from itself. Reconnect it and you should be good to go. ... Vacuums

I have a DC25 that will not pick anything up. It seems to be throwing everything back out somewhere. It only powers on when its not in the upright position. There is also a strange noise when it's turned on. I have taken the whole thing apart and cleaned all of the filters and checked for blockages but it hasn't help.


Hi there,\015\012\015\012Sorry to hear you're having a problem with your DC25. You should be able to resolve the issue by following these simple steps: ... Dyson DC25 All Floors Bagless Upright Vacuum

Why does the Eureka capture plus pet lovers put off a loud tornado siren sound when you turn it on. I cleaned the filters checked everything and it sounds like a tornado siren in the south. Email [email protected]


I would check your fan and see if any of the blades have been fractured. I had this happen recently when my vacuum caught a screw and the sound and vibration was deafening. ... Eureka Vacuums

Bissell healthy home vacuum will not turn on. I have checked everything on the vacuum. All the filters are clean and there are no clogs. I have had it for 10 months with no issues until now.


- The handle may not be installed properly, causing a loss in the power connection. Remove the handle completely. Slide the handle back into place on the lower section of handle and tighten the screw. ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

My russel hobbs mountain breeze ir purifier has a check filter light on even though ive just put in new all 3 filters....how do you get the check filter light off??


Push the mode and set buttons simultaneously to clear the check filter message from the display. ... Vacuums

Hello, I have a Eureka 71b handheld vacuum. There is literally no suction. I checked the hose and it is NOT clogged. I thought it might be the filter so I bought a new filter. Still no filter. The rot


... Eureka Vacuums

The vacuum does not have suction. I have cleaned the filters, checked the hose paths and the hose won't **** anything up. I even checked with all the filters removed, still no suction. It is blowing air out the exhaust.


Have you checked the belt? ... Bissell 89Q9 Bagless Cyclonic Vacuum

The brush rollers on my hoover mach 5 won't turn. I've cleaned everything and checked the belts and everything checks out fine. I had the vacuum for about a year.


I had the same problem. The problem is the small v-belt for the roller brush (Hoover part# 38528034). Although it looks in good shape, it's been stretched too large for the idler to keep good tension. The tension on that belt varies with the ... Hoover Vacuums

I have an electrolux Z8280 cyclonic twin clean vacuum cleaner 2000w. At the moment the power (blue) and filter light (red) are both flashing at the same time and it won't turn on at all. I have emptied the dirt, checked for blockages, and checked the filters and i still don't know what the problem is :( Can anyone help me? Thanks


It's REALLY easy: https://www.youtube.com/watch?v=HiHwY-lncc0 ... Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Replacing filter Got a Filter Queen Majestic vacuum from my inlaws when they moved overseas. I am in middle of vacuuming, got a weird noise, so opted to check and clean the filter for first time. UGH. The lower 'pot' that's the bottom part of the thing was full of gunk, but the filter pristine clean against the cone that's attached to the upper part of the unit. In other words, I am shocked to see that the dirt goes not INTO the filter, but outside of it into the bottom portion (that I call the


Its normal operation so don't worry ... Filter Queen Majestic Canister Vacuum

Have ultra vision and have changed filter and foam filter, checked all hoses but still will not pick up. Belt is fine and brush is clean and spinning properly. dirt stays at top of filter instead of falling into canister.


My kids get mine stuck all the time :(Take the vacuum outside then:Remove the hose at the bottom and see if there is any obstructions. Also shake the hose to make sure there is nothing in there as well or take it out side and make s ... Dirt Devil Vacuums

I have a Kenmore 116.36932 (upright-bagless vacuum) that the motor protector by-pass valve has opened. I've clean out the area between the agitator brush where the flexible extension hose starts. There was some blockage there. I checked the rest of the system (extenstion hose, back filter area, pipe area to canister and area to side filter. I took the 2 filters out and the by-pass valve is still open. Where else could there be a blockage that I can take apart to clean and put back together


... Vacuums

My Bissell 3920 motor is making a high pitched noise. I have cleared out pet hair from top to bottom. Cleaned the lower filter and replaced the upper filter. I Checked for blockage in the hoses and found none. The filter indicator goes green when I turn it on, but the straining motor noise persists.


Click on the link below to view the replacement motor and fan for your Bissell 3920 vacuum\015\012\015\012http://www.vacuums24x7.com/motorfan.html ... Bissell 3920 Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0502 seconds