Having problems with your Black & Decker CFV9600 DustBuster Bagless Upright Vacuum ?
Dustbuster 9.6v need diagram or photos of charger base and power cord
Repair Help & Product Troubleshooting for Black & Decker CFV9600 DustBuster Bagless Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Dustbuster 9.6v need diagram or photos of charger base and power cord
... Black & Decker CFV9600 DustBuster Bagless Upright Vacuum
I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.
You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum
While replacing my power cord on my DC25 a spring popped out I have no idea where it goes. I need a diagram so I can see where it goes
Here is how the switch assembly should go together: ... Dyson DC25 All Floors Bagless Upright Vacuum
Need parts diagram for euro-Pro ep601. I need to replace the power cord, but cannot get the motor gasket guard off.
Hi!You need to release a "clip" under the handle(this is on top of the dust cup) and then look for a hidden screw right under the thermostat label. ... Vacuums
Need a charging base for a Black&Decker CHV7200 DustBuster
You can find the charging base here. hope that helps.\015\012http://www.ereplacementparts.com/charger-and-base-p-102673.html ... Black & Decker Vacuums
I need wiring diagram to connect power cord, motor, and switch on a shop vac
... Shop Vac 84M200 Wet/Dry Vacuum
Rowenta Effective Steam Iron DX1700 Need wiring diagram. How do I wire the power cord to the internal Red, Blue, and White wires? What wires are neutral and which are hot?
The power cord is split near the base unit
There are 2 screws on each side of the top cover of the Rainbow ‘E’ series vacuum cleaners located behind the decal windows. To get to the screws; use a non-scratching tool such as a plastic putty knife and pry out a corner of the plastic ... Rainbow E series Canister Wet/Dry Vacuum
Need to replace power cord for bissell model 6585
A BISSELL Authorized Service Center should be able to help you out. You can find one nearest to you and call them first if you want: \015\012http://www.bissell.com/service-centers/?zip=Enter%20your%20zip%20code&distance=50&cid=ccsocial ... Bissell Vacuums
I have a Hoover Wind-tunnel Vaccum (Model U5433-900) that needs a new power cord. I am looking for step by step directions for replacing the power cord
... Hoover Vacuums
I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.
Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums
My dog chewed through the power cord on my Dyson DC15. I have purchased a new power cord and need instructions on how to remove the old one and replace it with the new one.
... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Need to replace power cord on Hoover windtunnel need wiring help
Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum
Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?
Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum
The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?
You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums
The power cord on a flat iron broke/got chewed through and needs to be replaced. how can I open it to get at the cord or fix the cord?
Need to replace the power cord
Pry out the clear plastic covering the Fins going around the body\015\012Surprise no fins in there but there are some screws ... Rainbow E series Canister Wet/Dry Vacuum
Need to replace power cord on Hoover vacuum.
Remove the dirt container and look for screws. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
Damage power cord needs to be replaced on Bissell 3920
... Bissell 3920 Bagless Upright Vacuum
Vacuum won't switch on;got it apart;cord ok;need wiring diagram
Its a great idea to write on paper how its connected . So it helps with dis assembly & reassembly . I tried a Internet search . Looks like it'd cost money for a service manual. Though. I found a Kirby Spares Website that could help. Although it d ... Kirby Generation 3 Bagged Upright Vacuum
Power cord wiring diagram
... Oreck XL Ultra Bagged Upright Vacuum
I need to replace power supply. where the cord
Greetings from GoVacuum.com,Unfortunately there is no fuse on a Kirby Generation model. In my 10 years of repairing Kirby's as well as other vacuums I will tell you that 9 times out of 10, when a Kirby Generation doesn't turn on, it's the ... Kirby Generation 3 Bagged Upright Vacuum
Power cord has been split accidentally - needs to be adjoined to new plug
... Dyson DC07 Bagless Upright Cyclonic Vacuum
I dont have a power cord and or foot pedal and need to know what I need.
Power cords can be found at http://search.totalvac.com/search?keywords=power+cord ... Vacuums
I need to replace the power cord. what tools do i need
The Kirby vacs have a 50year warranty. You sould contact the person you baught it from and have them replace it or if they gave you one (no labor is coverd on the warranty) then you will definately need a Philips screw driver and a tub to hold all th ... Kirby Ultimate G Bagged Upright Vacuum