Having problems with your Black & Decker CHV1400 Bagless Handheld Cyclonic Vacuum ?

Battery replacement I tried to follow the owner's manual instructions, but I have been unable to remove the battery cover.


Answers :

I have opened CHV1400 by removing two screws that are visible when you remove the "accessory" from its holder (located underside of the vacuum). After removing the 2 screws, I had to pull the green colored part by exerting slight force. You will now see the battery. It is held down by 2 more screws which are easy to remove.
Call a service centre for advice, ie 01543 275048.
Repair Help & Product Troubleshooting for Black & Decker CHV1400 Bagless Handheld Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Battery replacement I tried to follow the owner's manual instructions, but I have been unable to remove the battery cover.


I have opened CHV1400 by removing two screws that are visible when you remove the "accessory" from its holder (located underside of the vacuum). After removing the 2 screws, I had to pull the green colored part by exerting slight force. You will now ... Black & Decker CHV1400 Bagless Handheld Cyclonic Vacuum

How do I remove the battery in a Dustbuster chv1400 for replacement? I have removed the two screws and removed the cover, but I'm unable to figure out the retaining clips for the battery. Of course I don't want to break the clips.


That model looks similar to my DB200. Instead of the screws, the underside has a latch/panel that you remove. Place a screwdriver in the two slot-like holes that face each other (one at a time) and the 'door' should pop out. Mine was a little stiff ... Black & Decker Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I am trying to disassemble a electrolux 2100. I have looked at instructions given by Chemist 1961 and others. On the side, I have removed the rubber covers over the plastic rails but I can't remove the plastic rails that hold the rubber covers on. If I am right, these rails should just slide right out and the outer casing should come part.....or am I doing something wrong. I have pulled and pulled the rails and they don't budge. The rear end won't pop off. Help!


There's a tab at the back of the rail that needs to be released. Turn the vacuum on it's side, slip the tip of a standard screwdrive into the space between the rail and the back of the vacuum, and tap lightly with a hammer. Tap toward the front of ... Electrolux Lux 5500 Canister Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have a ge light switch receiver rf1023, with incandescent bulbs, and when I try to switch it on it just blinks once and goes out. if I hold the switch on the battery-operated wall remote, the lights keep blinking until I let go. It used to work fine, and now it doesn't. I've lost the intallation instructions, so I don't know if there was a trouble-shooting section that covered the problem.


... GE Vacuums

We bought a new home in march. It is a brand new home, with brand new First Alarm smoke/CO detectors. The very first night, we noticed the iving room (main) smoke alarm was "chirping". So we tried to replace the batteries, but when we did, all of the smoke alarms started going off (they are hardwired). We took out the new battery & dealt with the chirp. It is getting to be too much. So we are trying to fix it, but everytime we replace the batteries, the alarms are silent for a little bit, & then


... Vacuums

Battery replacement I would like to replace the battery on my handheld Black and Decker 9 volt battery Dust Buster. But where is the battery? How do I remove the old battery so I can replace with a new battery?


... Black & Decker CHV9600 Handheld Vacuum

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

I think I need to replace the main battery in my small floor vac - the one that can be hand held like a dust buster or work like a small floor vac. I need to know how to remove the battery and replace it with what kind of new battery..


I see my sense of humor is not appreciated...it was only a joke. Anyway, here is what you do: First, slide the battery cover off the bottom of the hand held unit. Remove the battery from the motor housing by pressing the tab on connector “A&rdq ... Vacuums

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.


Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How long are the batteries for virtual wall supposed to be working for? Even though I try to remove them after each cleaning , or use fresh batteries, the wall does not respond straight away. I can n


... iRobot Vacuums

Could someone please advise how to remove the cover on a Vax Power Pet 2. I'm trying to change the belt, have removed the screws from the sole plate but the cover seems to be held in place by the


Go here > http://support.vax.co.uk/power-2-upright and download the manual with full instructions ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.


... Vacuums

How do i remove the reel cover for my SEARS canister model 116312690 vacuum cleaner. we are unable to move the cord forward or back. We have found two screws, but are still unable to remove the cove


... Kenmore Vacuums

I have cleaned the filters on my dust buster. The vacuum works for a minute then the battery seems to wear out and the power weakens until it stops. How do I replace the battery on this vacuum? Do I need just one 9.6V battery? What screws do I loosen to insert the battery? I can't find my instruction booklet. Tank you for your help.


... Black & Decker 15.6 Volt DustBuster Vacuum

How do I remove the bottom cover on powermate #26412690 to replace belt?


... Kenmore Vacuums

I replaced the battery on my taylor 7334 model scale and still have no display. I tried taking the battery out, standing on the scale for 5 seconds, then putting the battery back. I still have no display. What can I do?


... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Good Day, We have a small hand- held Hoover rechargeable vacuum cleaner which no longer works (after about one year!!). Is it reasonable to assume the battery pack (Unitech NiCd SC 1200mAh 14,4V) is now useless? Is it worthwhile trying to replace the battery pack? regards Clive Sealey


... Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

I need to replace the idler arm assembly on a U6439-900 hoover wind tunner upright. I have the clear cover completely removed but still do not see how to remove old and insert new assembly.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a craftsman garage door opener remote control model TX2028 139.18191. The remote stopped opening or closing the garage door. I replaced the battery and tried to re-program it through the LEARN button as per the manual of the Garage 1/2 HP opener. The process has failed after several trials and the remote is still not working. Is there anything else that I can try or should I get a new remote. Thank you


... Vacuums

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0622 seconds