Having problems with your Black & Decker CHV1500 Bagless Handheld Cyclonic Vacuum ?

We ran our Platinum Series 18 volt hand vac until it stopped -- charged the battery overnight but it did not charge. is there a problem with the battery charger or what could cause this?

Answers :

Most problems with what you have stated have to do with bad contacts between the hand held unit and the battery charger.\015\012With the charger unplugged, make sure the contacts on both the charger and hand held unit are clean and not bent.\015\012Check to see what the "Light Indicator" should be when charging and reinsert the unit into the charger.\015\012If the light does not show what it is supposed to show, move the hand held unit around a bit to see if you can make the connection better.\015\012
\015\012If this does not do the job, depending on the age of the unit, might be time to replace the battery.
Repair Help & Product Troubleshooting for Black & Decker CHV1500 Bagless Handheld Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We ran our Platinum Series 18 volt hand vac until it stopped -- charged the battery overnight but it did not charge. is there a problem with the battery charger or what could cause this?

Most problems with what you have stated have to do with bad contacts between the hand held unit and the battery charger.\015\012With the charger unplugged, make sure the contacts on both the charger and hand held unit are clean and not bent.\015\012C ... Black & Decker CHV1500 Bagless Handheld Cyclonic Vacuum

The PCB controlling the battery charger is overheating and the led dosen't illuminate when charging, could the led be shorted internally causing the problem. The vacuum in question is a Hoover Freejet Cyclone SU144S2 001

The problem was caused by the failure of 7 of the 1.2volt cells in the battery pack, the other problems were symptoms of the battery pack failure. Replaced the thermal cutout a 131 degree C component on the PCB in the docking station for the vacuum w ... Vacuums

I purchased a brand new P113 Ryobi charger about 2 years ago. It has never worked. If I put a P104 battery in for a charge, it looks like it works correctly. I push the battery tester on the battery itself, and it says full charge, but when I go to use the bateery, it dies right away. I have tried three new P104 batteries. The batteries charge on my charger at work with no problem. The funny thing is, I don't need a battery in the charger and the charger does the same thing, It runs the test

If you have your receipt, check with Ryobi to see if it is still under warranty. It comes with either a 2 or 3 year warranty, depending on when it was purchased. If it is still covered, get it replaced/repaired. If it is not, buy the P117 charger. $3 ... Ryobi P113 18 Volt One Charger 140501001

My battery charger unit has stated to get hot while charging, is this a fault with the charger or the batteries. I would appreciate you advice

If the charger is left connected without the connection to the battery for several hours and there is no heat on the charger, then it is possible that the battery is using up more charging current .\012This results in heating of the unit for th ... Vacuums

Roomba 4270 stops too soon. my roomba got weird all of a sudden. it started not moving all over as it should. so I tore it all down as I had done before and cleaned all the hair and dirt out of every thing I could without getting down to the basic shell. it does work now and does move all over but stops after about 10 minutes. brand new battery so not a battery issue. could I have plugged some of the sensors in the wrong 'plug'

... iRobot Roomba 560 Robotic Vacuum

I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.

... Vacuums

I have iRobot Roomba 4210 and I have a problem with charge battery. The battery is new. When I charging a battery in other iRobot Roomba the battery was full charged. When I charging in my iRobot Roomba the battery was empty. My fast charger is OK.

The charging circuit on the main board is fried. This is a common issue. You need some good electronic repair skills, and equipment, to replace the problem components ... iRobot Roomba 4210 Bagless Robotic Vacuum

New battery!, roomba runs for 5 - 10 seconds, stops, starts running, stops, runs, stops, then beeps and low battery flashes. Have taken battery out, held start button 20 seconds, replaced battery and directly connect to charger, 72 hours min., still same problem.

... iRobot Roomba Discovery SE Bagless Robotic Vacuum

The battery charger flashes red when the battery is inserted for a charge - does this mean the battery is no good? If so, where can I purchase a new battery and at what cost? Thanks in advance.

Blinking red means it is charging. it will stop blinking when it is fully charged. ... Oreck TEK100 Handheld Vacuum

We have an Aquanot II charger for our backup sump pump. We unplugged the charger from the battery, and just plug the charger into an outlet. As soon as we plug it into an outlet, the two LEDs lite up, and then the fuse trips within a second. We bought the whole sump pump backup system in June 2009, so it is fairly new. Any idea whether the charger can be repaired?

Https://app.qleapahead.com/rtp/libraryget.aspx?asset=88182,63\012\012Above is the owners manual for your pump system. Included ar ... Vacuums

I have a wireless thermometer made by Viking (CE 0197). Have replaced the batteries of the remote sensor RF wireless. In the battery compartment there is button TX and a slide switch for position 1,2,3. Have replaced batteries pused button but no results of recording. Could you help me what to do to make the unit work again. Thank you

... Vacuums

My dc16 dyson root vacuum stopped working abruptly with no indication of a weak battery, the charger does not show a charge on battery. usually the vacuum slowed before it stopped with a dead battery, any suggestions

... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

I am currently unsure, it my Dyson DC16 battery is charging as it should. I read all the posts about Powersupply voltage of 28V and defective PCBs. I now need to know from someone who's DC16 is working properly what voltage the battery should have when it is charged. I currently only measure 24.2V in mine. Supposing there are 6 batteries in there with nominal 3.6 voltage each, which would add up to 21.6, I supposed one could charge with up to 25.2V (4.2*6) and once reach lower the voltage ke

Does it stop working real fast ? ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Thermal senser on the side of the vacuum motor there is a little thermal senser that has rust all inside of it ,my ? is will that cause the motor to shut down ,could the rust in the senser causing it to cut off ,cause the vacuum runs well then cuts off

If it is going bad, it will cause the motor to shut down, replace it then you will know if that is the problem or a problem with the motor itself. ... Vacuums

After charging overnight, Roomba only runs about 25 minutes before shutting down with a red light.At this point the battery measures 15.13 volts ( about 1.26 volts per cell ) My hobby experience is that a ni/cad or ni/mh battery nominal charged voltage is about 1.2 volts per cell, and that the recommended end point voltage should be about 1.0 volts per cell. Seems like the battery is ok, butsome kind of voltage regulator is shutting things down prematurely. Is this happening, and , if so, how ca

Reset the Roomba by removing it from the charger, then holding "spot" and "dock" for about twelve seconds. When you let go, the unit will play an ascending series of notes. Then recharge it overnight. If the run time is still short, give Customer Sup ... iRobot Roomba 560 Robotic Vacuum

Battery charger broken

CHARGER WONT WORK MEC B5265 CAN I BUY NEW ONE? ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Our favorite vacuum has stopped oerarating. We believe the battery needs to be replaced. WE HAVE LOST ALL DATA SHEETS THAT WOULD HELP US REPLACE (AND CHARGE) THE BATTERY<Is there someway you could get us this data. We will reenburse. Model R#MOD24A Thanks. Clay Collins

... iRobot Roomba 4210 Bagless Robotic Vacuum

Belt keeps sliding over on the roller bar and rubbing on plastic parts. Belt is a "U" belt and I am told it should be a "R" belt. Sears sold me a "U" so I will try and find the R tomorrow. What keeps the belt other than tension from sliding onn the roller bar? Could it be that just the wrong belt could cause this??

The 4870 Series uses Part number 61110. It is a "R" Belt. It will appear too be to large. This is normal. ... Eureka Smartvac 4870 Bagged Upright Vacuum

My Infinuvo Cleanmate QQ2 will not accept a full charge. It runs for 10 - 15 minutes and then says "battery low". I have a new battery and charger. I have charged it directly without the home base and have left it charging for days. Any suggestions? Thanks, Linda

... Infinuvo QQ1 CleanMate 365 Robotic Vacuum

I have lost my battery charger for my oreck stick/hand vac serial number 200041103780 for a 9 volt /300mA battery

... Vacuums

Miele power head battery charging problem - does not fully charge. I have had a new battery and charger - problem persists

... Miele Vacuums

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.

Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

My Electrolux pronto is slow to start, if it operates at all. The light on the charger doesn't stay on for more than a few seconds. Is it the charger, the battery, or the vacuum? Has hapened in the last few weeks. It is cleaned out, and generally well cared for.

I just wanted Electrolux to know that this is the Pronto 2-1 is the worst product I ever purchased. I thought after I received the new battery because of the recall it would work. \015\012When I was going to purchase the stick broom I was going ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

My Prosine 2.0 display panel displays Panel Fault: Memory error and the display error as well as all LEDs are off. The unit looks as if it has no power to it. I reset (power off.power on) the Prosine and all LEDs on the display (except for the back lit display) turn on for about 3 seconds then all go off again. I am able to use 120v RV Resort power and all 120v equip works. The Coach batteries do not charge and were low. I charged the Coach batteries with an external charger. The charge works ye

... Vacuums

My swivel sweeper battery will not hold a charge. The light is always red. I even bought a replacement battery -- same deal. Do I need to replace the charger also?

... As Seen On TV Swivel Sweeper Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0646 seconds