Having problems with your Black & Decker CK1300 Dustbuster Wet/Dry Vacuum ?

My dust buster smells awful when I turn it on!

\015 I purchased a used, but seemingly pretty new, good condition dust buster. However, whenever I turn it on to use it, it lets off this horrible smell! I looked to see if the filter could be cleaned, and it doesn't look like it can. Are there new filters you can buy? Any suggestions?\015

Answers :

Repair Help & Product Troubleshooting for Black & Decker CK1300 Dustbuster Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dust buster smells awful when I turn it on!

... Black & Decker CK1300 Dustbuster Wet/Dry Vacuum

When I turn on my Kenmore Premier 4.5 Peak HP 10.0 Amp after about a minute of running I get a burning smell. When I opened up the compartment that holds the dust collection bag, and remove the bag I found a filter. The filter was minimally dusty and has been cleaned. After sniffing around, I could not identify the source of the smell.

Dose it smell like rubber check your belt ... Vacuums

Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.

It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

Brush won't turn on the shark dust buster model SV75SP14

... Vacuums

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have had my Black and Decker Crush Master blender for years and have been happy with it. I made smoothies a few days ago and smelled a funny smell. I turned it off, but when I tried to turn it back on it didn't work, I even tried to plug it up in another socket, but it still didn't work. Is my blender beyond fixing?

Sounds like death to me,. you could take it apart to look see to be sure, what do you have to loose?Best regardsCk ... Vacuums

I had plugged it in to use it, turned it on and instantly it made a pop sound, smelled of electrical, and would not turn on after. i even waited for a while let the smell go away and tried a different plug in the house and still no operation of any kind. Is there an internal fuse that i could check on this? where is it located?

Sorry there is no fuse in the vacuum. It sounds like there is a short somewhere when they manufactured it. There is no way to fix yourself you will need to take to a repair shop\015\012\015\012Good luck ... Vacuums

Oreck XL My Oreck just turned off in the middle of vacuuming and I smelled a burning smell. I am thinking that if I can take it apart and remove whatever turned it off, it will run again.

Your roller brush is probably bound with hair and is not able to move ... Oreck XL2600 Vacuum

My Dirt Devil Vibe bagless vacuum started giving off a burning smell. The brush roller was jammed with hair. I immediately shut it off and cut the hair out of the rollers with scissors until it turned freely. When I turned it back on, the smell was gone but there's no suction now. Did I ruin the belt or something else?

It's more likely there's a clog in the hose somewhere, possibly where it connects to the power nozzle. Detach hose and check the PN. \015\012If there's no clog in the PN, detach hose completely from machine and try to drop a marble or coin th ... Windsor SR12 Sensor Bagged Upright Vacuum

I have Hoover Widepath Bagless 12 Amp Windtunnel vacuum. Yesterday I was vacuuming and smelled smoke and it shut itself off. Today I cleaned out the filters (they weren't bad) made sure nothing was obstructing the hoses or the spinning brush part. It turned on for 1 second, smells like smoke somewhere from the bottom and now won't turn back on so I don't know if anything is spinning or not. What can I do to fix this myself?

Hi There,\015\012\015\012When a vacuum cleaner smokes, it is usually only one of two possible problems.\015\012\015\012It could either be that your motor burned up, or that your belts burned. The belts on this particular mod ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Dust buster won't hold a charge, even if I let power run down to nothing and then charge it for a full day or two. This is the 2nd dust buster that has done the same thing. When I first take the item from the charger, it appears to have a very strong charge. Then within a minute, I cannot pick anything up. Thanks for your help.

... Black & Decker AV1200 DustBuster Handheld Vacuum

Dust smell I noticed a dust smell coming from the vacuum although I could see no sign of it leaking. It was as if it were blowing out dirty air.

Are all filters in place and clean check this first ... Dyson DC25 Animal Bagless Upright Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.

If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the oth ... Dyson DC07 Bagless Upright Cyclonic Vacuum


Mosture has gotten into the motor. Take the bottom tank off and let the unit run for 30 seconds. It will dry out the compartment ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like

I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?

Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

My dyson dc07 won't ****, and turns off immediately when i turn it on. It also smells funny like burning plastic when it is turned on. There are no blockages, and the filter it completely clean

Sounds like the motor is shot. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.

Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

When I was using my Bissell ProHeat 7901, I smelled something hot (almost burnt) and turned off the vaccum. When I turned it back on, everything seemed to be working, but the vaccum part was not making the same sound. The bristles are still turning, but it isn't picking up as much and is leaving quite a bit of lint on the carpet. Could the belts be worn? How do I tell? Thanks!

Ya that is probably the issue. Here is a link to the belts you need and to the manual which has instructions:Bissell ProHeat Belts and M ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Roomba is not picking up dirt but does pick up dust. That is, the dust chamber has dust in it but the dirt chamber is empty. The brushes don't have any fluff on them either which is not normal. The fan is blowing out plenty of air, the filter has been cleaned but we suspect the brushes aren't turning. an you help?

... Roomba Vacuums

Dust Buster has no suction

... Vacuums

Smells like burning rubber when I turn on my G6 Kirby vacuum.

You must take of the plastic ends from the wood beater bar and make sure the metal axels are not wound up with hair. I did this monthly with 4daughters ... Kirby G4 Bagged Upright Vacuum

Brand new 3HP shop vac smells like motor burning when turned on!

... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0724 seconds