Having problems with your Black & Decker PHV1800 Bagless Handheld Cyclonic Vacuum ?
Black and Decker PHV-1800: The flapper at the back of the nozzle came out. How can I reinstall it?
I have read other posts which note that while one can take all of the screws out of the nozzle assembly, it seems impossible to separate the blue portion from the white portion so that one can get at the flapper location. It is almost impossible. But not impossible. One can remove the blue portion of the nozzle. After removing all of the screws, gentle pry the blue portion from the white. While doing that, pull and wiggle the blue portion. Some gentle assists from a standard screwdriver proved helpful. With quite a bit of difficulty, and with some fear that something would break (but it didn't), it eventually came off. (There was no glue attaching it.). HOWEVER, to get the blue section back on, it proved necessary to cut off some of the blue plastic in strategic spots so that it could be returned to its original location. A Dremel tool did the job.
Repair Help & Product Troubleshooting for Black & Decker PHV1800 Bagless Handheld Cyclonic Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Black and Decker PHV-1800: The flapper at the back of the nozzle came out. How can I reinstall it?
I have read other posts which note that while one can take all of the screws out of the nozzle assembly, it seems impossible to separate the blue portion from the white portion so that one can get at the flapper location. It is almost impossi ... Black & Decker PHV1800 Bagless Handheld Cyclonic Vacuum
Re installing flapper to prevent back flow - Black & Decker PHV1800 Bagless Handheld Cyclonic Vacuum
VAC EXPERT \012\012\012 Welcome to fixya\012\012Hello\012\012 \012\012I have a ... Black & Decker PHV1800 Bagless Handheld Cyclonic Vacuum
The back wheel came off and i went to put it back on and the other wheel that connects to the mechinism/gear height ajustment that goes up/down with a spring in it came off as well. i have been looking for a schematic to put it back together but cant find any.
You do not need schematics, it is fairly easy. Clean and lubricate the teeth on the inside of the front wheel shaft assembly. Insert the spring into small pedal and place the pedal designated opening on the Kirby front fan casing with teeth facing ou ... Kirby G6 Bagged Upright Vacuum
My cigarette injector nozzle on my Top-O-Matic keeps coming off. Why and how do I fix it? With glue? I put the tobacco in, and my empty cigarette tube on the nozzle, then use the hand crank to push the tobacco into the tube and the NOZZLE is coming off with the tube and the tobacco isn't filling the tubes. please email me back a response [email protected]
... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum
The tension knob came off of the front of my sewing machine while I was sewing. I cannot figure out how to put it back on. I have the metal rod that fits into the back of the tension knob, but cannot figure out how to put it back into place. Keeps falling off
It sounds like your machine is the kind that has a knob with a 'set screw', a teeny tiny screw that tightens and holds the thing in place on the rod. Look for a small hole, probably on the bottom and look for a very small screw near the machine. ... Vacuums
Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after
The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?
... Dyson DC25 Animal Bagless Upright Vacuum
My dc 25 stabilizer bar came apart and a spring came out. Its on the right side. I need to know where it goes back in.
... Dyson DC25 All Floors Bagless Upright Vacuum
Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430
Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum
I own a singer sewing machine model 4562 and tension assembly came unscrewed and now I don't remember how to put the pieces back together. Do yo have a diagram that can be emailed to me so I can put it back together? Thanks
I can not get the water, normal heavy traffic selector reinstalled after taking unit apart, i replaced the pump, and now i cannot get it back together, there seems to be a special way it goes together, and i'm not finding it. Are there any videos, or pictures that show how it should go back together?
... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum
I have a Flotec shallow well FP4122-08. A burglar stood on the pump this summer to gain access to my goats building (window). There's a small black tube that came off at both ends. When I put the tube back on, it shoots right back off as soon as the pump is plugged in. I don't know the name of the part (tube) to order a new one, and I don't know if it just plugs onto the fittings of both ends, or goes into the pump at the end with the round fitting on it.
My Oregon Scientific BAR888 has 5 windows, 1. temperature, 2. humidity, 3. mb/hPa or inHg (switch at the back), 4. bars showing pressure changes over 24 hours, and 5. time/date. Window 3 gives an option to set something between 0 and 2500. Oregon say they only have one set of instructions for the BAR888 but they do not match my instrument as there is nothing included for my window 3. Trouble is I don't know what the 0 to 2500 relates to and therefore don't know what to set it at.(My model does n
My Rainbow SE vacuum was working fine until I ran over the edge of a rug and it went in to the nozzle. I immediately switched the vacuum off and proceeded to move the rug. When I tried to turn the Rainbow back on the brush was no longer spinning. I've tried the reset button and checking the nozzle for any debris, there are none. The brush just won't spin.
Hello lilbutmunch1,\015\012The brush is motor/belt driven so you probably either broke the belt or it shifted off the motor or brush shaft. I suggest you unplug it,flip it over and look for screws that hold the baseplate together.. remove those ... Rainbow E series Canister Wet/Dry Vacuum
I just bought a Kirby Sentria vacuum and shampooer less than a month ago. When they came and done the demonstration at my house they did not leave a manual or any instructions. They said they would be back the next day but have not been back. I need to clean my couch and have no idea how to hook up the attachments. Can you please help me?
... Kirby Ultimate G Bagged Upright Vacuum
Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o
Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f
I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums
The belt came off. How do I get it back on
The front square trim peice actuallys turns to open up to replace the belt onto the drive spindle ... Kirby Generation 3 Bagged Upright Vacuum
Dyson DC-07 Hose Wand Spring Came Out. How to put back in?
You'll see that there is a round piece with a cross shape on the inside of the button wand release button - place the end of the spring over the cross - you'll see the same cross on the collar of the machine...it'll take some doing, but line the othe ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Insert assemble came apart on the bottom of tank on my bissell 8920 how do i put it back together
Here is the Instruction or User Manual for the 8920, series machines ... Bissell Brushroll Proheat 2X 8920 9200 9400
How to put power nozzle back together e-series
... Rainbow E series Canister Wet/Dry Vacuum
How to put back wheels on a miracle mate power nozzle
... Miracle Vacuums
Dyson animal We bought a Dyson Animal from Sears a few years ago along with a service contract. We took it each year to be serviced. One year I took it because it lost it's suction. They sent it to the factory, but it came back still not working right. We did the same procedure over ands over many times than I can remember. I now have the cleaner in my garage and am using my old vacuum because I just can't seem to get anywhere with Sears. Please help me. We paid almost $600.00 and now it can't b
As someone who works for Sears, let me just say right now.. The service contract you bought sucks.. and does not really do anything for you. it was just a wast of money ( they have a new one now.. thats so much better because you get your money back ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Hmmm Hi there, I actually had tried everything you mentioned except for the vinegar idea which I'll do when I get back up to my home in Oregon. I checked for pinches, the heater, etc. Water does NOT come out of the accessory tool and only will dispense out of the main area for a second or two..any liquid actually starts filling up the area right behind the nozzles and around the pump instead of OUT of the machine. I checked gaskets, made sure there was a tight seal, and even made sure the little
Check the nozzles to make sure they aren't clogged. Sometimes there is a problem with the flow indicator cap, maybe too tight or not tight enough. Try squeezing the trigger while turning the can one way or the other. If at a certain point it starts ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Tv well it wont go back to number 6 which is the output for the direct tv hd box.There are 7 total outputs and it only letting me get to 0,7 every thing in between it wont let me get to.
Did you try unplugging you box from the a/c power. If that doesn't work, then you should call Direct TV, they need to reset your box. ... Vacuums