Having problems with your Bosch 1450 w 12 amps ?

How do I fold down the vacuum handle so I can cacuum

How do I fold down the handle of a Bosch 1459 w 12amps vacuum the carpet

Answers :

Repair Help & Product Troubleshooting for Bosch 1450 w 12 amps

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have the purple Animal model. When I step on the front of the cleaner to lower the handle then try to push to vacuum it "folds" up??


You need to click the handle in/out there should be a release button in-front of it. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

My vacuum hose has split very close to the handle- how do I remove the handle, cut the hose at the split & reattach it to the handle unit - Centralux central vacuum system. Where can I find a diagram of how to remove the handle?


Do Not Cut the hose! It has wiring inside to control the vac and power head. This is a swivel handled hose with both low and high voltage contacts in it. The same wiring which gives the hose its ribbing, is conducting current for two applic ... Electrolux Centralux Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.


... Hoover Vacuums

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

I have a Kenmore vacuum cleaner model #116.34720. The problem I am having is that if you are rolling the vacuum around, the base will drop without pressing on the handle release pedal. This often results in a bunch of dirt being dumped back out. The manual doesn't show anything about adjusting the handle release pedal so it holds the handle and base in an upright position better. Any help is greatly appreciated! Thanks in advance!


... Vacuums

Power Problem Whenver I push the power button on the handle the vacuum stays on for a few seconds then turns off. I have to push the button on the handle all the time to keep the vacuum working.


Hi There,\015\012\015\012Unfortunately this is being caused by static electricity building up in the electronic controls in the handle of the hose. I've seen this problem on numerious occasions, and in fact I have the twin brother of t ... Miele Blue Moon Bagged Canister Vacuum

Telescopic handle I don't think I have the exact same vacuum, although mine is a fantom upright bagless. I can't get the telescopic handle to stay in place. It pulls out whenever I try to pull back the vacuum. Any tips would be helpful! Thank you


Sometimes the locking mechanism for the wand wears out, make sure u have it all the way in and look where it locks and see if it looks worn ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down


... Eureka Vacuums

Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???


Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have the top of the line kenmore canister vacuum. According to the bottom plate the model nimbler is 116.28015700 I was doing the normal vacuuming and the bag full light came on and the vacuum action stropped. There is still power to the mortorized handle and agitator attachment. Is there some type of circuit breaker reset button for the vacuum function? This unit is probably less that two years old and has had very little use


... Kenmore Vacuums

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]


Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh


Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums

Putting new vacuum together position of the handle


The handle should be attached so that the open portion of the handle is facing towards the brushs( away from user) ... Dyson DC14 Full Access Bagless Upright Cyclonic Vacuum

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r


... Vacuums

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the


Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.


Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

I just received an older model Dyson DCo7 animal vacuum. When it is turned on and you are vacuuming, should there be suction at the top of the handle while vacuuming the floor?


No it should not ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Kirby Heritage Vacuum Cleaner. Recently the handle fell backwords. I took the pin to the handle out and replaced it. It helped some, but the handle does not stay upright.


... Kirby Ultimate G Bagged Upright Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0854 seconds