Having problems with your Bosch BSA2822 Pro-Parquet Bagged Canister Vacuum ?
Hi, the wire will not recoil. It is at full length...
\015 Hi the wire will not recoil. It is at full length.\015\012thanks\015
Repair Help & Product Troubleshooting for Bosch BSA2822 Pro-Parquet Bagged Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Hi, the wire will not recoil. It is at full length...
... Bosch BSA2822 Pro-Parquet Bagged Canister Vacuum
My Dewalt dc500 wet/dry vac won't **** anything up, I’ve put a piece of wire to not the float ball from moving them it work fine but if I remove the wire I stop working the float ball moves to the top like it is full of water? Can you please help?
... Dewalt DC500 Canister Wet/Dry Vacuum
Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?
The item is a revolution pivot racing technology vtec controller race&rally motor sports full competition model it does air&fuel ratio & controller the vtec just need the wire diagram to it
Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl
There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums
Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.
... Sanyo Vacuums
The extendable wand is jammed at full length and will not push back in?
Try a little wd40 or tap it lightly at the top. ... Dyson DC25 All Floors Bagless Upright Vacuum
I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put
... Panasonic Vacuums
Trying to wire aa Nutone model 763RL bath exhaust fan/light. The conduit coming from the breaker box has a red wire, a black wire, a white wire and a ground. The fan has two white wires, one black wire, one blue wire and one green wire. I have wired the whites together, but do not know how to wire the blance.
'Bag Full' light indicates at 1/3 bag
The sensor is a small hole into the vacuum chamber. It moves the alert system as vacuum inside the unit builds up.\015\012\015\012The filtration, built into the bag, is getting filled up and creating a higher vacuum inside the unit, givi ... Windsor SR12 Sensor Bagged Upright Vacuum
I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks
... Bissell 3750 Lift Off Bagless Upright Vacuum
I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you
Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums
Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?
... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
Reinstalling a hampton bay ceiling fan model-HL52QV P 3LC14 and I do not recall how to wire it to the house electric. A black wire and a blue wire are tied together and a white wire are present fromthe fan. Whichone is connected tothe hot wire in my fan electric box inthe ceiling.
The black and blue wire should conncect to the black wire in the electric box and the white wire should connect to the white wire in the box. This assumes the wiring was correctly installed.Jim ... Vacuums
Explain how to re-wire 16gal craftsman shopvac,switch wires are- 2 orange wires, one white, one black and one green(grd wire), I pulled them off and don't where each wire goes.
Im not looking at a diagram of your machine.\015\012\015\012Typically, in a switch circuit ... the green goes through; the white goes through; the black is broken by the switch.\015\012\015\012The two orange wires you speak of ... Vacuums
I have an antique 8 arm chandlier and want to put it up in my bedroom but the wire hasnt any differance in color, how do i wire it to the exsisting wire from the celing , what wire goes to what wire ? I wont be installing it myself but would like to know so i dont sound so silly
Starting with the proper wire gauge, always white to white and black to black. ... Vacuums
My son and I are trying to build a small motor for a school project. we have a 6volt battery 2 wires that we are hooking up to a spool of wire. We have two aposing magnets on each side of the spool of wire. the spool of wire is on a shaft and should turn when we touch it with the 2 wires from the battery. It just does not work. What are we missing here? Thankyou
Hello\015\012Please refer to the PDF document on how to build a small hobby DC motor.\015\012Go to the link below. Thanks\015\012 ... Vacuums
Wiring Just removed hair, etc and had to remove the motor and clipped the light wires. Reinstalled but blew lights. Wired series> wired parallel> deffinetly wired wrong have a diagram?
First, what is the model number? I'll shoot you a wiring schematic. ... Oreck XL Ultra Bagged Upright Vacuum
Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.
... Kenmore Vacuums
Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?
They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums
Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?
Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin
Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin
Hello, First check the cord to make sure you have continunity throw both leads, check\015\012them at the cord reel, there are 2 wires hooked up to it, if not then\015\012the cord is bad. Check the swith also, the next cause would be the\015\0 ... Miele Cat & Dog 326i Bagged Canister Vacuum
How to install a new motor in a filterqueen canister vacuum the old motor was 5 wire and the new is 4 wire. Wire colors are not the same.. - No, I have not disconnected the old wires.
According to my parts house, there's a 4-wire motor for some of the filter queen models and a 5-wire model for other filter queen models.You can still purchase a 5 wire motor. Check out greatvacs dot com. They carry both 4 and 5 wire. ... Vacuums
Hello, I,ve just bought an Italian designed 3 bulb 70's wall lamp. It has a 2 wire lead feeding out with 2 wire lead running from one bulb socket To the other 2 inside the casing. I'm trying to wire it in my porch which has 3 wire cable coming from a 13amp plug for power. Any suggestions on making this work please ?