Having problems with your Bosch BSG71360UC Bagged Canister Vacuum ?

I have a Bosch Elector Duo Hepa, BSG71360UC/07. I'm trying to replace the rectangular-shaped part with the carpet brush that attaches to the bottom of the wand. Where can I find this part?

Answers :

Repair Help & Product Troubleshooting for Bosch BSG71360UC Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch Elector Duo Hepa, BSG71360UC/07. I'm trying to replace the rectangular-shaped part with the carpet brush that attaches to the bottom of the wand. Where can I find this part?

... Bosch BSG71360UC Bagged Canister Vacuum

I sucked up a sock into the carpet attachment of my electrolux 3500 series and the carpet attachment cut off. After the sock was easily removed (it was only wrapped around the brush part) I reattached the carpet attachment, turned the vacuum on and flipped the switch to turn the carpet attachment back on, but it won't come back on. How can I fix it?

Did you press the reset button? There will be a reset button either on the back of the unit just below the bulkhead or on the top side of the base.\012\012Locate the reset button and press; this should allow the carpet attachment to resu ... Electrolux Epic 3500 Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I was vacuuming with the Dyson DC 17 and sucked up a berber carpet string by accident and after cutting and pulling it all out of the bottom brush part, the brush no longer spins but the suction part works. What do I do?

The belt could be snapped. If this model has a brush protected belt then it has to be repaired by a service call. If however you can get to the brush roll belt by removing the bottom sole plate (turning over the vacuum so that you're looking at the b ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I need to replace the cord on the beater brush attachement for s3614 hoover powermax.. can't find parts. I was able to pull apart the brusher, but I cannot release the wire to resplice and reconne

... Hoover S3614 Vacuum

Hoover turbo power 1500 have part of bottom off to replace belt but can't find where to attach it? must be more parts to take off but how?

... Hoover Elite U5061-900 Bagged Upright Vacuum

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?

Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

My Kirby shampooer - G4 - hardly used any water from the tank and no suds at all. Pet hair did blow out of the small slotted holes in the tray as I moved the shampooer back and forth, but the carpet was basically dry. I did vacuum before shampooing, so the brush part seemed to work great during shampooing, but no water! The small screen was stuck in the crook of the hose that attached to the tank so I did get that out and put it on the small hole on the tank, but it didn't make any difference. I

Few things:Make sure the sponge and the valve under the sponge (water tank) is clean.Make sure you follow the instructions (f you do not have the manual you can find one ... Kirby Ultimate G Bagged Upright Vacuum

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david

Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

I have a Lux Floor Pro Heavy Duty carpet cleaner. Whis attachments (scrubbers) do I attach to the bottom to wash a non-plush carpet. I have three attachments that have hard bristles and three that have soft bristles (they look like hard floor attachments). When I used the ones with hard bristles it sounded funny

NEVER USE THE HARD BRUSHES ON CARPET ! You can burn up your motor, break the drive belt,or strip the drive gears The black bristle brushes are for all carpet types. \015\012The hard bristle brushes are made for hardwood and other smooth ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?

You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I want to brush the pile up on my carpet do I need a special attachment to do this??. I have shampood it and it still seems a bit flat. When I shampood no water/foam filled up in the front tray???I am sure I had attached everything correctly. The only thing I can think of is when I attach the brush and tray to the front of the machine, do I turn the handle back to the right way up, or do I leave it upside down, this is the one that picks up the belt.

Here's my online guide for using the Kirby shampooer....\015\012\015\012 ... Kirby Ultimate G Bagged Upright Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

Need part no. 010-1181 carpet tool scrub brush and part no.01606965 carpet tool

... Bissell 1631 PowerSteamer ProHeat Canister Vacuum

My steam mop gets hot but steam is not coming out when i pump it. However when I release the bottom attachment steam comes out of bottom of the base (purple part). I took the attachment off to see if it was plugged but dont see anything. Any suggestions?

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My Kirby Heritage II vacuum is not picking up dirt up out of the carpet like usual, and I have to keep setting it lower to pick anything up. I finally get it to such a low setting that it starts sucking the carpet up and makes a whirring noise, and starts smelling. Every time this happens, we find the belt has been burned. We are wondering if the brush roll inside with the brushes that pick up dirt are worn out and too short?

... Kirby Heritage II Vacuum

My carpet cleaning brush does not turn on. The vacuum cleaner works fine but the the carpet cleaning attachment does not get any power so the light does not come on & the brush does not spin

... Kenmore 25512/ 25513 Progressive Canister Vacuum

I own a Eureka Optima 437 and one of the rear wheels are broken and cannot find parts for this. Where can I find parts for real wheel? I have a rear wheel that came off too. The wheel seems fine, but the plastic base that the wheel clicks onto on the underside of the vac seems to have cracked. I need a new plastic bottom. Any ideas?

Called Eureka Customer Service and ordered another part. They are mailing it to me free of charge!No more problem. ... Eureka 431A Optima Bagless Upright Vacuum

I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.

Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Replacing filter Got a Filter Queen Majestic vacuum from my inlaws when they moved overseas. I am in middle of vacuuming, got a weird noise, so opted to check and clean the filter for first time. UGH. The lower 'pot' that's the bottom part of the thing was full of gunk, but the filter pristine clean against the cone that's attached to the upper part of the unit. In other words, I am shocked to see that the dirt goes not INTO the filter, but outside of it into the bottom portion (that I call the

Its normal operation so don't worry ... Filter Queen Majestic Canister Vacuum

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1288 seconds