Having problems with your Bosch BUC11700UC Cyclone Jet Bagless Upright Vacuum ?

Bosch vacuum Motor turns off after a few minutes

\015 The motor will turn on at first and work but then turns off after a few minutes. It is still getting power because the headlights stay on. Any ideas? \015\012Thanks\015

Answers :

It sounds like you have a motor protection fuse that resets after an overheat/cooling cycle.These work the same as a circuit breaker in your house with the difference being they can reset themselves.The Bosch will also shut down if there is insufficient airflow and I would check your filters first.1) Pull the filter and let the machine run.Do not pick up debris when you operate without a filter-it will be drawn straight into the motor.If it runs fine without shutting down, all you need to do is change your filter.If it shuts down again check the external hose for any blockages.Also check the throat from the powerhead for any blockages.If you continue to have the same problem then you will need to replace the fuse because at this point you have eliminated all the other likely problems.Good Luck-Scott
My vacuum has the same problem when the filter needs to be cleaned. Just twist the filter cover to take it off, then press the red button on top of the canister to release the filter and pull it out. Fine particles of dust collect on the filter causing the motor to overheat and shut off. Take an old toothbrush and clean the filter. Install it once you're done, and the vacuum should work fine.
Repair Help & Product Troubleshooting for Bosch BUC11700UC Cyclone Jet Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch vacuum Motor turns off after a few minutes

It sounds like you have a motor protection fuse that resets after an overheat/cooling cycle.These work the same as a circuit breaker in your house with the difference being they can reset themselves.The Bosch will also shut down if there is insuffici ... Bosch BUC11700UC Cyclone Jet Bagless Upright Vacuum

I have a Kenmore Elegance Vacuum with Dirt Sensor, Model # 116.30750400C, Serial number M41901532. When vacuuming the carpet the power head will work for 3-6 mins then automatically shut off, power is still there and lights work but the power head motor turns off and the suction stops. I will turn it off and on, check the outlet, flick the on off buttons...nothing. I will turn it off for a couple minutes and it turns back on and runs like normal. I've check the bags, filters, cleaned the hos

It is an electrical problem in the handle, if you can or know somebody that has any fix it ability it can be fixed in about ten minutes. Oh, and Sears SUCKS!! ... Kenmore 34612 Bagged Upright Vacuum

I was just using my Bosch 1450W bagged vacuum and all of a sudden, the motor just shut down. No warning, no problems. The light still turns on, but the motor is unresponsive. There is a clean bag and filter, and nothing caught in the front roller. The motor sounded fine - no shaking, or weird frequency variations. There were no weird smells, just a little bit of heat, but nothing beyond normal. I've had this thing for several years, and never had a bit of trouble with it. Any suggestions

Many vacuums have internal thermal switches that need to cool to allow the vac to operate. After 30 minutes, check all 3 air filters and try again.\012Gary ... Bosch BSG71310UC Bagged Canister Vacuum

My vacuum cleaner will run for a few minutes and then shuts off. The plug light on the panel blinks. I thought the motor was shut, but after a long time it will turn on again, but again, only for a few minutes and then shuts off again. Any ideas? I bought an Oxygen Ultra a few years ago, but I don't like it nearly as much as the old Epic.

I know nothing about your particular vacuum, but many vacuum cleaners these days have\015\012safety cut out's, which causes the motor to do exactly what you describe. Sadly blockages, faulty switches, over stretched cables, carbon brushes etc c ... Electrolux Epic 6500 Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan

Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

I have a BISSELL CLEANVIEW II, I turn the power switch to "on" and am able to clean carpet for 1/2 a minute until the power shuts off in the outlet the vacuum is plugged into! The same repeats itself! I wonder if the motor is damaged or just plain shorted out!

Well yes in deed it is time for a new vac. for the motor bearings or armature are ceasing up ang causing the breaker to pop. if the vac. cord is hot then you know for sure... ... Vacuums

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio

Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.

When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a Kirby G4 Vacuum Cleaner - MOdel G4 D. I have never had any problems or repairs done to it in the past ten plus years that I've had it. This is an upright vacuum. I was vacuuming the carpet floor and was not having any trouble at all. I switched the vacuum off and moved it into a different room. When I tried to turn on the vacuum, it would not turn on. I checked with different outlets, used both front attachment and hose attachment. Checked the front part of the motor/ spiral case. This

Hello,\015\012My educated guess is that it's either the switch or the power cord. Here are a couple of guides to help with diagnosis and repair...\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

Bosch BSA2222UC canister vacuum shuts off after 5 minutes

I took apart the vacuum, removed the circuit board and cleaned the tiny bits of dust off it carefully, removed the cord winder (without letting it unwind) and carefully replaced both parts, blew dust out of the 2 armature brushes (lifted out the moto ... Bosch BSA2222UC Compact Plus Bagged Canister Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.

The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v

Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.

Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

I was vacuuming the vent in the bottom of the fridge. I must have picked something because the motor got wildly noisey. I cleaned out hoses, etc. There is no suction. I can see the blades of the motor and they are not turning around. Model U4269-930 Series B.72. Can I get at the motor to see if something is keeping the blades from turning? What would be your suggestion. Many thanks. Pat Sauerman

Hi Pat, my name is John I will do my best to assist you.\015\012\015\012You certainly can get at the motor, with simple hand tools. \015\012\015\012Referring to this ... Hoover Vacuums

The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.

This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?

Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

Nutone model cv-350 vacuum motor will not shut off. I have to unplug system in garage. I disconnected wire to house vacuum inlets and motor is still running. There must be a reset on the motor. I have turned the external switch on and off and still no help.

Mine is the same, and it is the relay welding itself closed. The relay is switched by the low-voltage wiring that connects to the vacuum outlets, and it switches the motor on and off. Mine was welded in the energized position. I have cleaned and file ... Vacuums

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.

... Miele S251 Flamenco II Bagged Canister Vacuum

Vacuum wont **** and turns off after 2 minutes of vacuuming

You must av some of the blanket still stuck in there that's why it keeps stopping because it's overheating check for more blockages ... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Hoover zoomi stops working after 15 minutes vacuuming, and takes at least 30 minutes to turn back on?

... Hoover Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1015 seconds