Having problems with your Bosch Eureka Readyforce Bagged Canister Vacuum, 900a ?

The on off switch is broken on my Eureka Readyforce model 900. There are no visible screws and I can't figure out how to remove the cover with the swith.

Answers :

Underneath there's a 1-inch long screw at the bottom of a three-inch deep hole. On top, if you raise the bag cover a bit, you will see a screw in a hole on each side of the vacuum. Close the cover, you don't see the holes, open the cover too far, you can't get in there with a scewdriver. Good luck.
Repair Help & Product Troubleshooting for Bosch Eureka Readyforce Bagged Canister Vacuum, 900a

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The on off switch is broken on my Eureka Readyforce model 900. There are no visible screws and I can't figure out how to remove the cover with the swith.

Underneath there's a 1-inch long screw at the bottom of a three-inch deep hole. On top, if you raise the bag cover a bit, you will see a screw in a hole on each side of the vacuum. Close the cover, you don't see the holes, open the cover too far, y ... Bosch Eureka Readyforce Bagged Canister Vacuum, 900a

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o

Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help

Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!

Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?

Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian

... Panasonic Vacuums

I cant figure out how to remove the housing cover

Hello,\015\012\015\012Here's an excellent video showing you how to replace the clutch on a Dyson vacuum cleaner. It's a moderately difficult repair, but this video really helped me the first time I had to do this repair. I hope this he ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do I remove the battery in a Dustbuster chv1400 for replacement? I have removed the two screws and removed the cover, but I'm unable to figure out the retaining clips for the battery. Of course I don't want to break the clips.

That model looks similar to my DB200. Instead of the screws, the underside has a latch/panel that you remove. Place a screwdriver in the two slot-like holes that face each other (one at a time) and the 'door' should pop out. Mine was a little stiff ... Black & Decker Vacuums


It is a snap lock plastic cap on mounted to the frame. ... Bissell 9200 Upright Vacuum

We have a Eureka Chinese p.o.s, model 6831. The brush roller won't turn, appears to be plugged with cat hair dang long hair cat. I cannot figure out how to remove the cover without breaking it after removing the screws, there is a u shaped collar on the tube in the way. Can anybody help?

There are a couple of tabs on both sides of the top housing that need to be unlocked by using a flat screw driver, then the top will come off. The u shaped collar on the tube will then give way to take the roller brush out to clean. ... Vacuums

Dismantle hoover sc211 . The auto cable rewind does not work and I need to split the machine. I have removed alll visible screws, but there must be some hidden screws at the switch end>

... Hoover Vacuums

Need to remove bottom cover of Panasonic MCV7314 vacuum to see if the belt is broken. I can't figure out how to remove and can't find a manual online.

I did a search for the manual for that model and found a pdf file online that had instructions and pictures. It was still slightly different and hard to get off. I took out two screws and then held in two side "clips" and wrestled it off. I dont t ... Panasonic Vacuums

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.

... Sanyo Vacuums

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?

... Panasonic MC-V7515 Bagged Upright Vacuum

I have an older Kenmore vacuum cleaner - Model #3285590C, Serial #DG4117817. I can't seem to figure out how to get the motor cover off. 2 bolts in the front have been removed but the back has no visible bindings. It seems to be held from inside the compartment! Whats the catch here!

... Kenmore Vacuums

Cant find screws to remove cover to check the belt

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

How to open main case on a dc08. i have removed the two screws under the top filter but i can not figure out how to seperate the main case so i can replace main switch. any help would be much appreciated

... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Need to replace impeller fan on Classic III. Half the blades are broken off. I can't figure out how to remove it. I have taken cover off.

... Kirby Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.

Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Dyson slim cannot remove switch cover

Here is video for DC07 switch replacement,http://www.videojug.com/film/how-to-replace-a-dyson-switch-and-actuator-dc07 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.

The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]

... Miele Vacuums

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.

Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.

Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

How do you remove the switches housing cover on a Dyson DC25?

... Dyson DC25 Animal Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0837 seconds