Having problems with your Broan-NuTone CV450 Central Bagged Central System Vacuum ?

Will not turn off when hose is pulled out of wall

Answers :

Some units have an on/off switch on the power unit itself. Check to make sure that is not turned on. Unplug your power unit and remove the 2 low voltage wires (not the power cord itself) . The low voltage wires start at the unit and run throught your home and attach to each hose inlet. They are usually attached to the unit by simple wire terminals or wire capped to small wires coming out. Just unlug the terminals or unscrew the wire caps and pull the connections apart. Plug your machine back in. If it still comes on the problem is the relay or circuit board/switch/ relay assembly inside the unit. If it doesn't come on with the low voltage wires unattached then you may have two wires touching somewhere in the low voltage wiring.
Repair Help & Product Troubleshooting for Broan-NuTone CV450 Central Bagged Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a central vacuum system. When I disconnect the hose from a wall outlet the central canister does not shut down dispite my turning off the vacuum at the handle of the hose. The only way I can get the system to shut down is to pull the plug at the canister. What gives? Rob

What I'm hearing is the canister(Not the Powerhead) portion of the unit is running all the time unless you unplug it. this problem could be caused by a short in one of your low voltage lines running through the house. To determine that just unplug on ... Vacuums

Unit goes on when turn unit on but doesn't pull when hoses are put into wall

The system could be blocked. \012\012the bag door could be open on the unit. \012\012The little black gasket between the dirt pail and the main body of the unit may be missing. \012\012Check those and you may solve ... Broan-NuTone Vacuums

Will not turn off when hose is pulled out of wall

Some units have an on/off switch on the power unit itself. Check to make sure that is not turned on. Unplug your power unit and remove the 2 low voltage wires (not the power cord itself) . The low voltage wires start at the unit and run throught your ... Broan-NuTone CV450 Central Bagged Central System Vacuum

The Vaccum is not turning on when i plug the hose into the wall. The hoover system will turn on when i turn the switch on at the base and wont go off till i turn the switch off. But it will not come on automatically when i put the hose in to the wall connections. Many Thanks Linda

You can test this out by taking a small metal spoon and with the bottom side of the spoon insert it into the vac outlet on the wall. you want to touch the two metal pins inside the vac outlet to test if the unit is the problem or the hose is the prob ... Beam Industries Vacuums

My BROAN CV-110 hose with the rug beater only works if I turn it on from the base unit. Shouldn't it turn on when I plug the hose into the wall recepticle? Do I need to replace the hardware at the end of this hose and if so, where would I purchase that? This central vac came in a house I just purchased. Thanks for any help. Sherry

... Broan-NuTone CV450 Central Bagged Central System Vacuum

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.

The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum

Dyson dc41 wont suck up on hose and hose pulls back when turned on

... Dyson Bagless Upright Vacuum DC41 Animal

Every time we plug in the vaccum hose into the wall recepticle the vaacuum turns on for half a second and then blows the circuit breaker. This just started a few days ago. We tried replacing the 20 am

... Dirt Devil CV950 Central System Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.

The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

I have a eureka cv2301b central vac system that turns on and works when the system is plugged in but when operating the hose and head inside the house you cannot shut off the system even if you unplug the hose from the wall... Whats going on

... Eureka CV2301 Bagged Central System Vacuum

My dyson DC17 will not turn on unless the handle is pulled back.(into the vacuuming position) The attachment hose will not work at all (0 suction thru it). I've checked the hose and made sure there is no obstruction. Any ideas?

Not sure if I can help, but I'll try. The DC17 has two motors: the vacuum motor and a separate motor for the brush bar. It is normal that the brush motor works only when the handle is pulled back in the vacuuming position - that's the way it's made. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Our Easy-Flo built in vacuum system will not turn off, even when the hose is disconnected. We have to turn it off manually. Could it be a short in one of the wall outlets causing this?

Some models have an on/off switch on the power unit itself. This switch is used to turn your power unit on when you are right at the machine. \015\012 If there is no switch on the power unit, unplug your power unit from the wall socket, loo ... Easy Flo EF1400 Central System Vacuum

Progressive canister turns on and off when you pull hose.

I saw this on another FixYa post -- it tells you how to remove the wand cover safely---\015\012Comment posted on Feb 09, 20082bubbles\015\012ok here we go.. fine a small file that will fit the holes at the bottom\015\012of the wand and break th ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I installed the Hoover Wind Tunnel Central Vac in my new home. After connecting the wall outlets and successfully turning on the system from the hose control, I discovered there is lots of air flow t

I would recommend checking your wall outlets where the hose plugs in for any type of clog in the tubing. If the vacuum itself ... Vacuums

Single lever Eurostream faucet with cold water filter side tap and a pull out rinse hose. Turn water on it stop flowing within seconds.

... EuroSteam Vapor Steam Cleaner Vacuum

My nutone vacuum system won't shut off when I pull the hose out of the wall...any thoughts

The relay that turns the machine off from any of the several places where you connect, is probably stuck.\015\012\015\012The relay is operated by low voltage. When you connect your hose, you comlete the low voltage circuit and energize th ... Broan-NuTone CV450 Central Bagged Central System Vacuum

My Electrolux central vac wont cut off when you turn the switch off or unplug the hose from the wall. Any suggestions? Sheldon

Hi,\012The realy that turns it on is stuck... the relay will need to be replaced...\012\012heatman101 ... Electrolux Central Vacuum

My vac will turn on at the unit but will not come on when I insert the hose into any wall outlet

The problem is one of two things...either the hose part is bad or the wiring to the unit is bad....all that needs to happen to make the unit come on is to short between (connect) the two wires going to the unit. Therefore if the hose part is not conn ... M&S Systems Vacuums

Model 116.1260 i can not figure out how to turn this vacuum on. is there a switch or do you just insert the hose into the wall socket?

Need the complete model #, 116.1260*****. I assume this is a built-in system? Yes you have to plug the hose into the wall outlet, and there usually is a switch on the hose handle to turn it on. ... Vacuums

No suction I have the central vac type. It has no suction at the can. I pulled the hose going to the walls and tested there...and nothing. I removed the dirt can and checked the motor ...it is spinning but does not feel like any suction. I checked the exhaust and it is pushing strong air out. I also cleaned the filter and still nothing. Is there a relay or something that would cause only exhaust air. I emptied the can of dirt and put it back together and have absolutely no air.....hear the motor

On some units there is a screen that protects the impeller of the motor. If this gets sealed off with debris then it is like putting a potato in the tail pipe of a car. Taking the top off the unit reveals the motor. DO UN-PLUG the unit first from th ... Electrolux Central Vacuum

Vacuum only turns on in reclined position/pull out hose broken

Per the Dyson Web Site I found the solution. Although I cleared all the filters/possible clogs the vacuum had over heated disabling the pull out attachment and power button except when in the reclined position. After clearing the filter and waiting a ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka Boss Power Plus and the beater bar is rolling, the belt is turning, but after vacuuming up around the litter box (not a lot of litter), when I turn the vacuum off, the litter, or even household dirt, falls out. When I hold the vacuum back to turn it off so that it doesn't fall on the floor, it's sitting in the cubby where the wheels are. The bag is empty, the hose is not plugged, the hose is securely fitted on both ends of the unit. This vacuum was purchased in July and is being

Even though the brush is spinning, you probably need to replace the belt because it is s ... Eureka Vacuums

I was given a model 6591, plugged it in and it worked but didnt "****" and didnt sound right. I turned it off and removed the hose from the back found a badly plugged hose. Removed the hair plug cleaned filters and when I tried to turn it on again. Now the motor will not turn on or even make a noise. I hear there is a fuse that can be blown? How can I find the fuse if there is one? Thank You Ron

The User Guide for the bissell Clearview Power Trak\012\012http://canada.bissell.com/images/UserGuides/3590C.pdf\012 ... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum

Hose attachment On my dyson dc 25 the hose attachment is very hard to pull off. It seems like something is getting hung up when i try to pull up the hose.

Your wand is getting stuck in the hose because the hose is twisted - you need to unwind it:\015\012\015\0121) Pull the wand up as far as you can, all the way if possible\015\0122) Stretch the hose out and unwind it, use some babypow ... Dyson DC25 All Floors Bagless Upright Vacuum

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.

I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.4741 seconds