Having problems with your Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum ?

Nutone CV556 Vaccuum Cleaner -Continuously running

\015 \015\012Nutone CV556 Vaccuum Cleaner :\015\012====================== \015\012I have been using Nutone CV556 for over 5 Yrs. Today (Sep 08,2009) While vacuuming , after I disconnected the hose from the wall outlet the system kept running. Nothing can stop it . I tried the switch on the power unit (ON/ OFF) , no luck. I looked at the wiring in the wall outlet that initiated the problem, nothing unusual. Any help\015

Answers :

Start with this. Unplug the vac to shut off, then disconnect the low voltage wiring at the vac.Plug the vac back in. If the vac still runs you have an internal short on the relay or wiring inside the vac.
If the vac stops then the vac and final wiring is OK and the problem is in the wiring in the house.
Have you removed any inlets for painting or had any renos done or pictures hung. If so undo what you did last. If inlets were disturbed remove them and look for low voltage vac wires touching metal backing plates in the wall or touching the inlet mounting screws.
If you have done a reno or hung pictures you may have pierece the wire for the vac creating a low voltage short which will keep the vac running until removed. I have seen this happen with freshly installed 1/4 round molding along a baseboard
Repair Help & Product Troubleshooting for Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Nutone CV556 Vaccuum Cleaner -Continuously running


Start with this. Unplug the vac to shut off, then disconnect the low voltage wiring at the vac.Plug the vac back in. If the vac still runs you have an internal short on the relay or wiring inside the vac. If the vac stops then the vac and final ... Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

Nutone Broan CV556 runs continuously and will not shut off until I unplug it.. I disconnected the low voltage wires and it still runs when I plug it in. Inside the top of the vacuum are 3 electrical devices - one looks like a transformer wire -- one is a rectangular electronic black box. The third is an on off rocker switch. Which piece it likely to be shorted out? It is about 8 years old.


... Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

On my M&S Air Vac AV425 central vaccuum system, the system usually turns on by inserting the vaccuum hose into one of the vaccuum outlets. However, it now runs continuously. I am able to turn it off only by unplugging the vaccuum from the electrical outlet. I would like to know how to trouble shoot the problem or how to find someone who services Air Vac systems in the Bridgewater, New jersey area.


We are a central vacuum service company and we service all of new jersey. sounds like you have a short some where that keeps your unit running or it could be your relay module thats stuck our number is 908-721-7595 its j&j central vacuum services ... Vacuums

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.


The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum

I have a Nutone central vacuum model number CV450W that was working great until I recently removed the hose and it now runs continuously until I pull the plug....any suggestions please


Disconnect the thin low voltage wiring between the vac and the rest of the house. If the vac continues to run you have a defective relay in the vac motor housing. If the vac stops you have a short in the wiring in the house, likely behind an in ... Broan-NuTone CV450 Central Bagged Central System Vacuum

Bag indicator light won't go off, therefore vaccuum cleaner won't run. It acts as if the bag is full even with a new bag.


The bag indicator is either rusted out or broken. it only realy's on a little spring that bounces up and down so dont trust those things ... Vacuums

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1


Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

Dyson vacuum I have a DC07 vaccuum. The problem I am having is that the front does not want to stay down as I vaccuum and I continuously have to keep stepping on the front to make it go back down to the floor. It seems as though there is either not enough weight in the front or possibly the unit just has to be broken in so that there is not so much resistance between the handle and the front of the vaccuum. Could there be something I did not remove or is this typical on these vaccuums?


There is some thing broken it is two plastic cogs they help the front go down and stay up you will have to get a star screw driver and there should be two screws on top and two at the b ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.


Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum

The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?


Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum

We have a Bissell Proheat 2X (model 8920). The problem we are having is when water/soap is initially released (all settings) it continues to leak out the front water spray nozzles unit the water containers are empty. The vacuum works but can't keep up with the continuous water leaking out. Do you have any idea what is sticking open to allow the continued release of water when the machine is running? Thanks Rick


Return it. It is faulty and should not do that. Mine does not. Does require changing water about evrery 10 minutes but one can see the filth in the water. Also re-clean with plain water over areas that were cleaned to remove all cleaner. Old cleaner ... Bissell 8920 ProHeat 2XTM Upright Vacuum

I have bought a HOOvER freespace 2000W cyclonic vacuum cleaner but it runs VERY HOT and I am wondering if this is the usual running temperature. I have cleaned the air intake filter and removeed the e


... Vacuums

On my Kenmore 36932 upright vacuum, the agitator continuously runs. It runs when the vacuum is turned off.


... Kenmore Vacuums

Hoover carpet cleaner F6059 not running full light on


I would guess there is a switch above the float that would kill the power hope this helps regards Jim ... Vacuums

How to empty the bag of the cv556 - Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum


It actually isn't a bag it is filter. The stuff that you feel inside are weights. The filter will get sucked up into the vacuum when it is on and then the weights are supposed to help it drop and shake off. It is a permanent filter and I would not ... Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

Bosch Vacuum Cleaner: I changed bag. Cleaned out all suction hose and hepa filters, however, my 1450 w 12 amp upright vacuum cleaner will die after five minute run - overheating. Please advise.


Greetings from GoVacuum.com,It sounds like you may have a bad thermal switch inside the machine. Most vacuum cleaners have a switch connected to the motor, so if the vacuum cleaner is running hot, it will shut off to prevent any damage ... Bosch Vacuums

Our Bissell Proheat Carept Cleaner 1699 is not dispensing any soap; only weater is running thru the cleaner. We are using the Bissel cleaning soap, not an off brand. Any suggestions would be appreciated? Paul


Hi Paul,I just want to make sure that you still would like help with your Bissell. As you may see from my profile, when I help someone out, I always spend considerable time answering questions, taking pictures, and really making sure tha ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The Electrolux Prolux upright vacuuum cleaner vacuum motor is not running and the brush is working well. What is the problem and how to open up the cleaner


... Electrolux EL5010A Bagged Upright Vacuum

Dirt finder I have a Hoover U6439-900.  After the cleaner was used a few times, the dirt finder light cycles between green and red on the regular setting and will not go to green.  On the sensitive setting, the red light stays on most of the time.  I have tried to run the cleaner to remove any dirt but have not solved the problem.


The sensor may be bad, or it may be coated over with dirt. Re,ove the hose at the back of the vacuum, the head of the sensor is down inside that opening, reach in there and clean it off and see it that corrects the problem, if not replace the sensor ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Same problem as voirjs 12/29/09 - runs a while & needs brushes cleaned w/same repeat scenario. have been doing all of the cleaning as felix80 said on 1/8/10; but it still continues the run awhile & need cleaning behavior. a more indepth solution is required.


I called iRobot Customer Support, and they are sending me a new cleaning head module. ... iRobot Roomba 560 Robotic Vacuum

Fantom vacuum vacuum starts running fine at first,but after about 15 mins the suction stops but the vacuum continues to run


Sounds like a partly clogged filter ... Fantom Vacums FM741 Twister Bagless Upright Vacuum

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks


... Sunbeam Vacuums

When I sart to run my bagless vacuum, it runs for a second and then shuts off. I replaced the belt and the filter. The repairman told me that on bagless vaccuums, the motor and bearings get clogged w


Take the brush roller off and on the ends are the bearing caps.try to take those off and clean the bearings ,carpet strands and hair will cause that.after you do that make sure the roller turns freely if not then the bearings might be bad and if that ... Vacuums

The cleaner does not squirt out any cleaner or water. The machine runs but there is no moisture at all being dispenced.


These units have alot of pump failure problems. most likely the pump has gone bad. check the pump motor with a continuity tester if the pump motor is good disconnect the exit hose from the pump and see if it pumps any water ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a panasonic mc-ul975 vacuum that works great when working properly. the airflow through the canister seems to stops once the aero blast technology is done running which causes the vacuum to not function as it should (does not have as much suction and the hose/tool accessories do not work at all). if air is continually running through the canister everything seems fine. please help!


Hi there. In Panasonic vacuums, there is a thermostat protection on the motor. It will auto ... Panasonic MC-UL975 Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0656 seconds