Having problems with your Broan-NuTone CV750 Central Vacuum ?

Low voltage wiring

\015 My vacuum wouldnt shut off so i replaced the relay. now the vacuum shuts off but my outlets dont work\015

Answers :

Probably just didn't wire the l/v side of the relay properly. Or forgot to plug the leads from the outlets back in to the vac after you got it all hooked back up. Folks do it to me all the time and then make like it's my fault! Ha ha.

Jump the l/v contacts inside the CV. If it goes: trace outward toward the outlets to see if something shook loose while it was apart. If you can't jump the l/v with a plier/screwdriver at the CV or even inside it, you have an issue on the board (either how you've connected to it or it's defective itself). The prob is that there's dozens of diff board configs, plus the relays and transformers weren't together on the same board in the old days. If you've got one of these models with a massive transformer separate from the relays get out the test leads and make sure you've got adequate voltage coming out of her to power the relay coil.
Repair Help & Product Troubleshooting for Broan-NuTone CV750 Central Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Kenmore central Vac - where to connect low voltage wires?


Mosy central vacs have 2 spades close together that stick out on the side, usually where the circuit breaker and auto/manual switch is. This is where you plug the low voltage wires into. ... Vacuums

Nutone Broan CV556 runs continuously and will not shut off until I unplug it.. I disconnected the low voltage wires and it still runs when I plug it in. Inside the top of the vacuum are 3 electrical devices - one looks like a transformer wire -- one is a rectangular electronic black box. The third is an on off rocker switch. Which piece it likely to be shorted out? It is about 8 years old.


... Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

Kenmore Central Vac - Where to connect the low voltage wires


You need female spade connectors and most hardware stores should have them. ... Vacuums

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

Low voltage wiring


Probably just didn't wire the l/v side of the relay properly. Or forgot to plug the leads from the outlets back in to the vac after you got it all hooked back up. Folks do it to me all the time and then make like it's my fault! Ha ha. Jum ... Broan-NuTone CV750 Central Vacuum

How do I hook up the low voltage wires - Electrolux Central Vacuum


What are you hooking them to, the tank? on and electrolux system its just two terminals on the side of the tank and it does not matter what wire goes to what terminal. ... Electrolux Central Vacuum

Cv45w will shut off when low voltage wires disconnected


... Broan-NuTone CV450 Central Bagged Central System Vacuum

While sucking air out of the space saving bags the vacuum would not shut off when done. The unit only works when plugged in. Disconnected the low voltage wires and unit still runs, on/off switch does nothing.


... Broan-NuTone CV350 Performance Bagged Central System Vacuum

Eureka cv3291k Vacuum does not turn off. Is it easy to install and purchase a relay switch? I think that is the problem as when I disconnect low voltage wires it still turns on when I plug the vacuum in.


... Vacuums

NuTone CV750 Central Vacuum won't shut off. The on/off switch on side of unit has no effect. Did continuity test on switch, it tests ok. I've disconnected the low voltage wiring at the side of unit, that had no effect.


I will assume that you disconnected the switch from the circuit when you did the continuity test -- that is really important.\015\012If so, then i think that the relay inside the top of the unit is stuck on, or the low voltage wires (inside the ... Broan-NuTone CV750 Central Vacuum

Inop powerhead, low voltage found.


Should be 120 volts to power supply then 12-14 from power supply to main circuit board. and all of it's components and motor. ... Royal Procision 3050 Bagged Canister Vacuum

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?


... Oreck XL Ultra Bagged Upright Vacuum

We have a series e rainbow cleaner. my wife had been using it i turned off and turned the canister up sie down to get the serial number. it would not turn back on.we need a new hose and thats why i was looking for the serial num. it has a rocker switch and the motor will work on low but will not run on the suction side. i have checked the wiring harnesses out as best i could without taken it all apart. im wondering if it may be the switch. it started once and then stopped.


There is one way to verify if it is the switch.It's kind of dangerous though,but not too bad.You need an extra piece of wire,fairly thick.I would use 4 guage myself.Hold it with pliers,just in case it gets hot.Turn the switch on and hold the wire to ... Rainbow Vacuums

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug


... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

My Oreck 2600HH won't turn on. The wiring seems right, but when I check the black lead and white lead at the motor there was no voltage when I turned the switch on


... Oreck XL2600 Vacuum

Was turning on then off then back on now can not get to start at all even if i jump the low voltage line


Ensure filter is clean. Check switch near filter.\015\012Try reset switch. \015\012It could very likely be the circuit board/power module in the machine near the motor. It could also be a worn out motor. It's best to take to the neare ... Electrolux Central Vacuum

Trying to wire aa Nutone model 763RL bath exhaust fan/light. The conduit coming from the breaker box has a red wire, a black wire, a white wire and a ground. The fan has two white wires, one black wire, one blue wire and one green wire. I have wired the whites together, but do not know how to wire the blance.


... Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you


Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums

Explain how to re-wire 16gal craftsman shopvac,switch wires are- 2 orange wires, one white, one black and one green(grd wire), I pulled them off and don't where each wire goes.


Im not looking at a diagram of your machine.\015\012\015\012Typically, in a switch circuit ... the green goes through; the white goes through; the black is broken by the switch.\015\012\015\012The two orange wires you speak of ... Vacuums

Reinstalling a hampton bay ceiling fan model-HL52QV P 3LC14 and I do not recall how to wire it to the house electric. A black wire and a blue wire are tied together and a white wire are present fromthe fan. Whichone is connected tothe hot wire in my fan electric box inthe ceiling.


The black and blue wire should conncect to the black wire in the electric box and the white wire should connect to the white wire in the box. This assumes the wiring was correctly installed.Jim ... Vacuums

I have an antique 8 arm chandlier and want to put it up in my bedroom but the wire hasnt any differance in color, how do i wire it to the exsisting wire from the celing , what wire goes to what wire ? I wont be installing it myself but would like to know so i dont sound so silly


Starting with the proper wire gauge, always white to white and black to black. ... Vacuums

Wiring Just removed hair, etc and had to remove the motor and clipped the light wires. Reinstalled but blew lights. Wired series> wired parallel> deffinetly wired wrong have a diagram?


First, what is the model number? I'll shoot you a wiring schematic. ... Oreck XL Ultra Bagged Upright Vacuum

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0279 seconds