Having problems with your Carpet Pro 10 AMP Commercial Vacuum ?
Where is the reset button - Carpet Pro 10 AMP Commercial Vacuum
Repair Help & Product Troubleshooting for Carpet Pro 10 AMP Commercial Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Where is the reset button - Carpet Pro 10 AMP Commercial Vacuum
... Carpet Pro 10 AMP Commercial Vacuum
My vacuum is a Kenmore Special Edition with a Power-Mate 12.0 AMPS wand. I ran over the edge of fringed edge of my living room carpet and immediately turned off the vacuum. Although I have removed the fringe pieces from the wand head and I have pushed the overload protector reset button on the wand, the wand brush will not turn. Help- it's the Thanksgiving weekend and guests are coming soon! Thank you.
... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely
The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums
Why won't brushes move on Commercial Carpet Pro Vacuum Cleaner
Luvumuch48tj: Unplug the vacuum and lay it upside down on some newspaper. Remove the sole plate (bottom plate) with a screwdriver. Pull straight up on the brushes (called a beater bar) and remove the beater bar and belt. Remove the end ca ... Carpet Pro CPU-2T Commercial Upright Vacuum Cleaner CPU2T With On-Board Attachments
Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.
I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums
I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage
If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums
Dyson 28-animal- Power brush stopped working and power light and carpet level buttons all are blinking. Per the instructions vacuum needs reset by turning it off for 30 seconds. However after doing so it does not reset and work. Help!
... Dyson DC28 Animal Bagless Upright Vacuum
Central vacuum won't start even after depressing the reset button on the carpet sweeper. Hose and wand appear to be unclogged.
Is it only the power head that's not working, or the central vacuum itself? Disconnect wands from hose, turn on, and hold hand over hose end to check for suction. If none, go through first set of steps below.\015\012\015\012If the vacuu ... Electrolux Central Vacuum
Hi, I have an electrolux Ambassador and the other day I was vacuuming a fringe carpet and the fringe made the electrolux stop (has happened before) and when I pressed the reset button, the motor is on but the wheel does not spin. Any suggestions?
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=678083\015\012Generic problem for all Vacuums\015\012Hi, I have an Electrolux Ambassador\015\012Posted ... Vacuums
Is there a reset button on bissell 12 amp - Bissell 3750 Lift Off Bagless Upright Vacuum
... Bissell 3750 Lift Off Bagless Upright Vacuum
Electrolux Epic 6500 SR Carpet Sweeper won't go on. Belt good brush moves, bulb looks good, reset red button I'm not sure, works, looks good. Vacuum starts has suction ,
This link is the manualhttp://www.totalvac.com/manuals/electrolux_manual_Epic6500.pdf ... Vacuums
We have a commercial Simplity vacuum series 6 and we are not getting any power. We tried different plugs, changed bag, etc. but still no power. Is there a reset button anywhere? Any other suggestions? Thank you for any assistance!
Check the reset switch on the back of the machine toward the bottom. Maybe next to a silver sticker.If you need any help contact me.TimTheVacCenter.com ... Simplicity Vacuums
I own a Bissell Oxy Pro Carpet Cleaner/ Vacuum, I've had it three years but only used it twice. I filled up the water and cleaning solution and did everything I should do. The on button powered up
Cord shorted out and the vacuum quit will not restart. Is the a reset button Dirt Devil Swivel Glide 12 amp
... Dirt Devil Ultra Swivel Glide M086020 Upright Vacuum
Shark Pursuit Euro-pro X vacuum cleaner, 12 amp, upright model
This vacum cleaner is equipped for auto shut off when it gets hot , It gets hot when it gets clogged either the little sponge filter is to dirty or the the round white filter in the dust collecting container. ... Euro-Pro UV209 Upright Vacuum
I have a kenmore progressive vacuum with a belt reset button that trips out everytime you try to vacuum. It does it in about 5 to 10 seconds. Can I bypass the reset button or can you help me determine the problem. Thanks
A lot of times the reset button is tripping because there is a problem. The problem could be with the brush roller in this case. A lot of times I see this unit for repair and the end of the brush is so compacted with hair and debris that it has also ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
I have a Beam serenity plus SP800A vacuum, the red light went on and the bristles stopped turning when I vacuumed up my bathroom rug. what does the reset button look like. Or does this model have a reset button. how do I turn off the red light so that the bristles start turning again?
... Beam Industries 2775 Serenity Plus Central System Vacuum
I have a kenmore progressive direct drive handi mate jr. upright vacuum. My daughter used it last night to vacuum up some cat litter that had spilled on the floor. I went to use it today and it turned on for a second and then stopped working. I have hit the reset button but it will not turn on. Help this vacuum is only 2 years old Is there anything that I need to reset or do so that the vacuum will work again?
Its probably clogged up with cat litter.might have gotten into the motor.your motor has a motor guard inside if it. when it overheats it will shut down till it cools off.you need to clean all th cat liter out of it.and clean the filters.with a direct ... Kenmore Vacuums
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?
... Easy Flo EF2300 Central System Vacuum
My Kenmore 35922 works well on floors, but it recently became very difficult to push on carpet. The brush spins and a local vacuum repair guy wouldn't solve my problem since the vacuum worked fine on his very flat, commercial carpet. What can I do to get my easy to push vacuum back?
Hi dalee196,There are three common reasons why vacuum cleaners are getting hard to push.1. Base is dirty - The base needs to be clean from dirt and tar.2. Height is too low - You might want to consider adjusting th ... Vacuums
Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T
... Rainbow E series Canister Wet/Dry Vacuum
I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to
... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
I have the top of the line kenmore canister vacuum. According to the bottom plate the model nimbler is 116.28015700 I was doing the normal vacuuming and the bag full light came on and the vacuum action stropped. There is still power to the mortorized handle and agitator attachment. Is there some type of circuit breaker reset button for the vacuum function? This unit is probably less that two years old and has had very little use
... Kenmore Vacuums
Miele Champagne Vacuum Cleaner Model S548 I was using the vacuum as normal, moved locations so I plugged into another outlet & suddenly there was no power to the vacuum! I tried it in several other outlets, tried the reset button... & still no power to the vacuum. Any ideas what could be causing this? Any info would be greatly appreciated. Thank you!
Greetings from ,\015\012 \015\012This definitely sound like a cord reel issue to me. This is really the only problem that I ever see on a Miele vacuum cleaner. 9 times out of 10 the cord reel needs to be changed. If you purcha ... Miele Blue Moon Bagged Canister Vacuum