Having problems with your Carpet shampoo ?

How do I take a part my stream cleaner

Water is coming from the bottom

Answers :

Repair Help & Product Troubleshooting for Carpet shampoo

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Parts Hi I have the Eurkea steam cleaner model 2450 and was wondering how do you take the front part off where you can see the water sucking up from carpet so this can be cleaned. Also I think the spring in the part that holds the water has come off another part is this able to be fixed or can I just purchase a new water holding tank and if so where? Thanks


Click this link for spare partshttp://www.vacpartswarehouse.com/Eureka-2450-extractor-s/1802.htm ... Vacuums

I have a euro-pro vapor stream cleaner Model EP95. The rubber sleave inside the canister that connects to the hose is split. Can it I buy a replacement part?


... Euro-Pro Steam Cleaner EP95 Canister Vacuum

Sharp Ec-Cb20-S 2000w Vaccum Cleaner For 220v-12475 how take it parts


... Sharp ec-cb20-s 2000w vaccum cleaner for 220v-12475

I have a Hoover F5411 steamvac Jr spot cleaner and it won't spray and one of the answers was to turn it over and try to turn the impiller to see if it turns. Where is the impille? Is it on the bottom of the top of the steamvac or on the bottom of the part that takes in the recover water?


... Vacuums

I have a proheat carpet cleaner model 3 7901. the problem is the brush on the bottom of the machine plus the two end parts and the belt came out. i put everything back but they popped out, they are not staying in place. what am i doing wrong or what do i have to take out to get everything in place correctly?


Hi\015\012\015\0121. You’ll need to follow this procedure to assemble your unit back together.\015\0122. Make sure the foot pedal is in the proper position.\015\0123. The SmartMix should be properly loaded into the main ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Dyson DC04 i have a loose wire where the cable enters the cleaner how do i open the part where the on/off button is. A wire is loose probably but I cannot get to the interior to check its status. How can I take it apart? the plug is sealed but could it be a loose wire in there?


You have to remove the yellow switch but to do this there is a small hole at the side of the switch nearest to the machine you have to push something in this which will push the clip that is holding the switch if you can do this there is a screw behi ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Steam Cleaner EP95 Canister Vacuum: i have a Euro-Pro vapor stream cleaner Model EP95....


... Euro-Pro Steam Cleaner EP95 Canister Vacuum

I'm using Miele Medivac vacuum and I just sucked in a small plastic eye drop container by accident(I sometimes take off the brush part to **** in 'small enough' articles). And it is jammed in the part where the plastic hose connector bends. I think I can take it out if I can just disconnect the long necked plastic hose connector that connects the metal wand part and the hose part. Is it designed to be disconnected or should I not even try it?


I love the fact that the filter bleeped out s.u.c.k ha ha! ... Vacuums

Had infamous extra part once I put my steam cleaner back together


Steve, The o-ring goes inside the turbine assembly on the metal shaft. ... Hoover F7220900 SteamVac V2 Upright Vacuum

Dear tech, I have a 12amp bissel bagless cleaner model# 4220-P the part i need is under the foot lever to lower the vaccum cleaner to sweep. The part is the slide pin that locks the sweeper from lowering.It has a spring attach to it. can I buy this part bob Yurkovich


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=805734\015\012Generic problem for all Vacuums\015\012Dear tech, I have a\015\012Posted by yurk on Jul 1 ... Vacuums

Mystery part Bissell 1699-P. I removed the top cover and a part came tumbling out (from the rear of the machine - towards the handle area). I have no idea were this part belongs. I have a schematic of the cleaner but I can not locate the part on it. I tried to copy and paste a picture of the part but that isn't working so I will attempt to discribe the part: There is nothing stampted on the part that I can see. It is plastic(white), 2" long, 3/16" in diamater. One end is U shaped (u-shape is 1/4


One question... you haven't mentioned that the vacuum doesn't work now... as hard as this is to accept... if it doesn't effect the function... forget about it.... i could very well have been something you vacuumed up along the way.\015\012 ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

Bissell 7950 ProHeat Self Propelled Carpet cleaner Replacement Pump Belt part 215-0628


Normally, there is a post sticking out of the retainer to remove it. If the post is broken off, then you will have to lift the black arm and wiggle it at the same time and the retainer will pop up so you can remove it. On the belt side, the retainer ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Where can I get a complete factory list of parts numbers for the Bissell 3750 Series Bagless Vacuum Cleaner. I found an exploded diagram but parts did not have official part numbers listed.


If in Australia call godfreys vacumm they can probably email one to you or look up www.bissel.com and ask them ... Bissell Vacuums

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Bissell ProHeat 2x, and I did something dum. I had some powdered cleaner that said it works with carpet cleaners-well I mixed it in-and the next time I tried to use it, nothing came out. So, I took it part to check what was wrong-and found out that the powdered cleaner solidified in places. I cleared the nozzels, nothing. I think the solenoid, between the heater and nozzels is pluggd, and possibly the heater. I've got a question-could I use CLR to clean the heater, with replacing t


Heck yeah, give it a shot. Try running some water through it too- fill it up, heat it just to where it's hot and unplug it, shake it around and dump it out. Repeat. You might have to get a wire or something to go through and get the powder loosened b ... Bissell Vacuums

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks


Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums

I have an old Progressive vacuum cleaner that says "Hepa Filter" and "Whisper Belt". Not sure what the model # is. The problem is that the vacuum part itself (the part that touches the floor and rolls over) has ejected its filter that we can see through the little window- it just came out under the rollers under the device... we cannot see how to re-insert this piece of filter which looks like a kind of round, flat grey foam/fabric and clearly goes inside- (top of the part that touches the flo


Check this procedure:\015\012\015\012Unplug the appliance that you will be \015\012changing the filter in.\015\012\011\011\011\011\011\011\011\015\012\015\012\011\011\011\011\011\011\011\011\015\ ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Part replacement we have one of your "Shark steam cleaners", that while moving from one room to another, was dropped. The head separated from the part that holds the water and broke in the process. Can this part be purchased.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I need a replacement part for the S3325 Shark ultra steam blaster hard surface cleaner: part #22, Accessory Adapter, on page 3 of the owners manual. Euro Pro shipped me a totally wrong part. Can you help me find this adapter? Thank you.


... Euro-Pro S3325 Handheld Steam Vacuum

No parts list in the user manual, thus can't search for a specific replacement part for Fantom FM740 vacuum cleaner!


Go to this link for parts for fantom fm740http://www.vacpartswarehouse.com/Fantom-FM740-Bagless-Upright-s/4164.htm ... Fantom Vacums FM740 Twister 300SE Bagless Upright Vacuum

Schematic parts diagram for bissell proheat 9200 carpet cleaner


Hi, just go to amazon here: Amazon com bissell proheat carpet cleaner parts and you can find every needed parts. I hope this was helpful. Cheers ... Bissell 9200 Upright Vacuum

Motor Brushes (Part 4370655) for Sears Canister Vacuum Cleaner


... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

Parts can u tell me where i can purchase parts for my shark tm steam cleaner please. Thankyou


Call them at 1-800-798-7398\015\012Have the model number, the country it was made in and the date it was\015\012made. All found on sticker on bottom of unit. They are foreigners that\015\012answer the phone, so be prepared to spell everything. ... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0640 seconds