Having problems with your Clarke Vacuums ?
Parts for Clarke Parking Lot Sweeper
\015 I'm looking for a bag part # 760649 for an old Clarke Vacume for sweeping parking lots. It looks like it was made in Muskegon MI.\015
Repair Help & Product Troubleshooting for Clarke Vacuums
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Parts for Clarke Parking Lot Sweeper
... Clarke Vacuums
Dear tech, I have a 12amp bissel bagless cleaner model# 4220-P the part i need is under the foot lever to lower the vaccum cleaner to sweep. The part is the slide pin that locks the sweeper from lowering.It has a spring attach to it. can I buy this part bob Yurkovich
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=805734\015\012Generic problem for all Vacuums\015\012Dear tech, I have a\015\012Posted by yurk on Jul 1 ... Vacuums
Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina
Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum
I have a Shark sweeper Model # V1900W would like to know how to get replacement parts. The rubber sweeper on the under side is coming apart and is interfering with the operation.
... Euro-Pro S3325 Handheld Steam Vacuum
I bout this vacume in mid December 07 and about February-March it started not picking up the dust on the floor. So in early April I bout a new filter and it still wasn't picking up the way it had in the beginning. I've taken it a part several times and cleaned it out with it being plugged at the bottom hose with dust bunnies. Well I just took it back to Walmart where I purchased it and I failed to keep the reciet they could not do any thing about the sweeper. I went back to the sweepers and re
Pull the hose out of the holder, is there suction there. If not, then there is a clog in the hose. If there is suction, then check the dirt outlet by the brush roll. Also if the belt is slipping, it may appear to not have as much suction, belts wi ... Dirt Devil Vacuums
The sweeper part is on, but the canister part is not
The problem is most likely the switch. It could be a bad/worn switch, or simply a broken wire or bad connection to the switch. An easy fix at an authorized Electrolux service center. ... Electrolux Vacuums
Model v1945zn, handel broke at base and doesnt connect to sweeper where can I find replacement part
... Shark Vacuums
Show all parts dc17 dyson sweeper
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Kenmore Model 116.33922 or 116.33923 upright. The vacuum cleaner does not have any air suction through the floor sweeper part. It does in the hose. I changed the filters. What next?
... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
The sweeper parts that spins just stopped spinning, what I do, I don't know where my owners manual is?
Sound like your belt broke. most vacuums the bottom plate comes off or the top cover can be removed to access the belt area. ... Vacuums
Loading my 52148 Scunci into the back seat of my truck the connector from the bottom of the handle to the top of the unit snapped off. It appeared to have a pivot ball that went into the sweeping unit to move,turn and pivot the sweeper. I could rig it to sort of function but if the lower handle part is available it would be nice to purchase one, if available. THANX, Don Colo Spgs Colorado
... Scunci 52004 Bagless Canister Vacuum
I would like to know where i can get a manual for the bissell 3760-4 model. i bought this sweeper used and i would like to get a book on the parts . thank you for your help
BISSELL User’s Guides can be downloaded at www.bissell.com\015\012On the front page under Customer Service click on User’s Guides and enter the model number of your unit.\015\012User Guide will be displayed as a PDF file. ... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum
Not exactly a blow gun. Convertible blower/vac - Sears Craftsman. Wire broke off ONE brush in the motor. Paid about $90 for the vac - Sears lists the WHOLE motor as one part - $88. Have requested brushes (they are provided with a lot of my 'cheap' Harbor Freight tools) but no go. Just get the canned reply - buy the whole motor. Actually got it working again... CAREFULLY drilled and tapped a 4-40 screw into the brush and soldered the lead to that... Always a way, isn't there?
I have a Shark corless sweeper since Nov 2004 and it now makes a lot of grinding noise. How do I get rid of the noise, it works well but noisy....
If its that old the plastic gears and parts are probably wore out. Euro pro does not provide many parts other than belts. might be time to replace it ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray
Seal where coffee grounds screw in is leaking water.seal has lot of tiny splits in the fine seal that fits inside the s/s disc.Where can I get a replacement part. BREVILLE CAFE ROMA MACHINE Mike Happy
Http://www.ereplacementparts.com/breville-esp8xl-cafe-roma-espresso-machine-parts-c-116052_116055_ ... Vacuums
I have a Euro-Pro Shark Cordless Sweeper Model UV610. The motor still runs but the spinning brushes are no longer spinning. Can someone that is familiar with this appliance please assist me at repairing it and/or what parts I may need for repairing it? Thanks T.R.
IT SOUNDS LIKE YOU HAVE A BROKEN BELT, THAT CONNECTS THE MOTOR TO THE ROTOR BRUSH. ... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum
Fan housing my sweeper was making noises when you turned the brush so i tore it apart and found that the fan and the casing that covers the fan is broken. I can't find parts cause i don't even know what i am looking for. i believe i have a discontinued vacuum as well
Http://www.hoover.com/ will help you find a local repair shop and they can get almost anything Hoover as long as it isn't a crank model. ... Hoover U5254-900 Vacuum
Is it a good idea to lubricate any of the plastic parts on the 12amp upright bag sweeper? If so, what should I (and shoud I NOT) use to do so?
Old fashioned Vaseline ointment is probably the best lubricant to use. Works great and is longlasting. Don't use liquids/oils. ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum
Have the empower upright cleaner. belt broke. can not find part #36528-040belt. can find a lot of hoover belts but not this #.Is there another hoover belt that will work on this vac?
No. if the wrong belt you will have problems. This is a common belt for Hoover, it used to be 36528027, but the number changed to the 36528040, also 40201190 is the newest number for this belt. Most repair vacuum repair shops should have this belt. ... Vacuums
Hoover steamscrubber I loaned my vac to my daughter who used it to clean shag carpet with lots of dog hair......now the scrubbers wont spin I have taken them (scrubbers) out and cleaned the vac....don't know where the lint trap is...but i DON'T see any part moving that would make the spinners rotate either Thnks...Lydia
I had the same problem. Fixed it by taking the machine apart and lubricating the bearing inside the turo tunnell. It's a pain, but not impossible if I could do you can. You must start by taking off the cover. Don't forget the scvrews on the front by ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.
You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums
I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil
Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums
I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.
... Kenmore EVO All Surface Floor Cleaner Vacuum
I am getting a lot of dog hair on the filter after cleaning one room, this is something new. I cleaned as many parts as I can. It seems like the dog hair is moving from the clear canester onto the top of the filter, any thoughts??
The cone in the tank has a black gasket make sure it hasn't slid to far up ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Need to clean the front part--lots of hair stuck in it!
Cut it out with sissors! Just cut along horizontally the you can start pulling the stuff out. I hope this is what you mean.\012Dee ... Vacuums