Having problems with your Clymer Harley-Davidson Dyna FXD Evolution 1991-1998 ?

No spark,no power to ignition module

\015 Changed all the fuses,have power to everything but the ignition\015

Answers :

Do you have power to the fuse? Sometimes fuses look good, but are actually bad. Check with volt-ohm meter. otherwise bad connections and or wire, corrosion causes a lot of bad behaviors, clean to bright metal for all connections and contacts. Again check with volt-ohm meter, or "indicator" light method.
Repair Help & Product Troubleshooting for Clymer Harley-Davidson Dyna FXD Evolution 1991-1998

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No spark,no power to ignition module

Do you have power to the fuse? Sometimes fuses look good, but are actually bad. Check with volt-ohm meter. otherwise bad connections and or wire, corrosion causes a lot of bad behaviors, clean to bright metal for all connections and contacts. Agai ... Clymer Harley-Davidson Dyna FXD Evolution 1991-1998

How do i replace the power switch on a DC04? I can't get to the switch, are there any special tricks to open the swich module?

Yes there is a trick it you look at the switch cover at the edge nearest to the handle you will see a little groove down inside it is the clip that holds the cover on it iis part of the the switch cover and it is hard to remove without breaking it,yo ... Vacuums

I'm installing a new ignition module on a bc24w weedeater trimmer--the part has 2 screws holding it on-it is apparently adjustable--what gap setting should I use between it and the magnet (armature & rotor??) Also what is proper spark plug gap? Thanks

I usually use a match book cover between it and the magnet. this way the gap is about right and it will not hang on the magnets. put through both sides at once, then push it in and tighten it up. then take out guage. spark plug gap is .025, the armat ... Vacuums

Spark to everything but the ignition module. - Clymer Harley-Davidson Dyna FXD Evolution 1991-1998

... Clymer Harley-Davidson Dyna FXD Evolution 1991-1998

SubBrand name 'Exmork', 5 Kw Sine wave inverter Intermittently, breaks into a spurious mode which causes it to draw excessive current while the output waveform becomes seriously corrupted with severe transient spikes close to the crossover point. We have available oscilloscope images showing the problem graphically. We have four of these inverters out in the field, and they all exhibit the problem from time to time. The fault has precipitated failures in the Power-board module in two units

Had similar problems with my inverters a while back tried to sort it out myself all to no avail. Eventually found out it was a problem from the manufacturers and all that were produced had the same fault. Had to change my brand to Su-Kam inverters. I ... Vacuums

We have a Kenmore canister vacuum cleaner 25614504. It has in intermittant light and power flicker in the power mate unit as it is moving over the floor. This behavior can be simulated by jiggling the power cord where it eners the power mate. I do not know how to enter the power mate to see if there is a loose wire.

... Kenmore 28614 Canister Vacuum

Miele S514 Solaris Electro Plus with Power Brush. Bought it in 2003. I love it, except the Power Brush just lost power so now I can't vacuum the carpets. I believe it is a SEB 212-2 Power Brush. The vacuum (canister) is Black. Any help is appreciated. There is no power to it at all. I've unplugged it, smacked it around a little too (mostly kidding) but still nothing.

... Miele S514 Solaris Electro Plus Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto

Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.

You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.

First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum

No power i try to turn it on no power i treid different power source no luck check everything no power

It could be the switch button that you push to turn it on (2031199), or the switch (2031243) could be the problem. If not those 2, then the cord could be bad or even the motor (2031214). I would check that switch button first. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Changed the motor carbon brushes on my Beam central vacuum cleaner equiped with an IntelliWatch system. This system includes the Alutron DB100 module. This Alutron module needs to be reset so that the vacuum cleaner can operate properly. I believe that this module keeps log of running time and disables operation after a predetermined time. Can you help me with providing a reset procedure that will reset this module. Thanks

... Sunbeam Vacuums

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david

Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

I was vacuuming with the regular nozzle and all was well. Then I changed to the powered nozzle and the 2nd power level wouldn't work and then when I detached the powered nozzle I was unable to turn it ....there was no suction. The lights are on for low and high level but not middle level power.

... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

The model is Miele S538, but I did not see it on the list. The suction power button( ) increasing the power does not work. The suction power button (-) decreasing the power does work.

... Miele Leo S5381 Canister HEPA Vacuum Cleaner Bagged Vacuum

I have an electolux EL7001 canister vacuum. When I attach the large power nozzle....the one for the carpets not the small one for the floors...the nozzle is not powered unless I strap it on with duct tape. Is there some piece I can purchase that will secure the connection between the wand and the power nozzle head so that it is powered without the duct tape?thank you.

... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Was using my Miele Champagne vacuum, powered down, changed the bag, and now I have no power. I checked to make sure all lids were securely closed, still no power. Checked to make sure outlet was working, still no power...help.

Most likely the cord went bad, one side of it opened up, you will have to replace the cord reel asm. if this is the problem, Could also be a switch, electronic control or the motor. ... Miele Vacuums

Our Electrolux canister vacuum just stopped working when we were vacuuming the floor. The power does come on when the power head is attached but as soon as the power head is removed the power shuts off. I tried pressing the reset button but that doesn't help. Is there a solution that I can try at home?

Sound like you problem is in the connection going to the power head you will see a small screw on the power nozzel where it joins to the handle take out the screw and take it a part you will see where one of the bars have been disconnect from the pow ... Electrolux Guardian Bagged Canister Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920

You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

When i hit the power button on my miele carina, it doesnt lock and stay on. i have to hold down the power button for the power to stay on. Please advise

Try a little WD-40 sprayed sparingly on the button. work the button a few times- may be sticky spring or contact. if that doesn't work, check with retailer where you purchased it- see if you can get a replacement switch! if you're handy, or have a ha ... Miele Carina Vacuum Vacuum

I have one central vacuum location that does not receive power. All other locations work. I do get suction but just no power. What should I do first to test power to location.

You need to use a circiut tester (electrician test probe) on the two terminals the hose plugs in to to see if power is present to connect to. The receptacle likely has damage to the power connection from arcing from the hose previously not fully plu ... Hoover Powermax U5242-930 Vacuum

I have one central vacuum location that does not receive power. All other locations work. I do get suction but just no power. What should I do first to test power to location.

Remove the face plate from the wall and test the low voltage wiring behind. Before undoing the screws where the wiring connects, reach inside the inlet and feel the two brass pin connections. There should be spring tension behind each. Underneath the ... Hoover S5604 Central Vacuuming System Power Unit Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0422 seconds