Having problems with your Clymer Harley-Davidson Dyna FXD Evolution 1991-1998 ?

What position should the fuel shutoff be in for a 98 Dyna Wide glide

Answers :

Repair Help & Product Troubleshooting for Clymer Harley-Davidson Dyna FXD Evolution 1991-1998

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What position should the fuel shutoff be in for a 98 Dyna Wide glide

... Clymer Harley-Davidson Dyna FXD Evolution 1991-1998

Ryobi RPBV2500 My blower only seems to ant to run when the choke lever is at the first position. It did run with the choke completely off but seemed to suffer from what I thought was fuel starvation when it ran for awhile. When I took the fuel cap off it would start up again, making me think it had a fuel lock. I had a garden centre with engineers look at it.They said that they had checked the carb and could find no blockages. Can you please help?

... Vacuums

How many filters does the bagless dirt devil vision wide glide have cause the motor sounds fine but it doesnt **** hardly

Check and clean the hose. ... Vacuums

Dirt devil envision wide glide. doesn't have much suction at suction hose end. will not vacuum up anything. Belt is good, hose has been cleaned out, all to no avail. Help !! : ) Ernie Bernard

... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

The dirt devil vision wide glide Model 086700W appears to have no suction. I have cleaned the hoses and filter and still there is nothing being picked up. Also, I have checked the belt.

There must be a blockage after the hose, check where the hose plugs into the vacuum. make sure unit is un plugged for safety ... Vacuums

The cantister on my DC04 no longer stays secure when in position. It does not snap and lock into place as before. I found a small plastic tab about 1/4 inch deep and less than an inch wide on the floor. Looks like it has broken off the lockin mechanism any suggestions?

Check your warranty. If it's still good read to find out if this part is covered (probably not) and where to take it for repair or replacement of the tank. \015\012Unfortunately, it may turn out you'll need to buy a new vacuum. ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

Dirt devil vision wide glide

... Dirt Devil M086700 Vision Bagless Upright Vacuum

Dirt Devil M086700 Wide Glide upright suction problem

You can go to hoover /dirt devil but there are a lot of parts that are no longer available for that model.i have one also.need the cradle for the hos at the bottom but not available..call all-type vacuum and janitorial supply .lisa may be able to fin ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?

Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a model 2016S chain saw and need to know how the fuel lines are hooked up from the fuel tank to the primer bulb and to the carburetor. does the filler line in the fuel tank go directly to the carburetor or does it go to the primer bulb and then to the carb?

Tank filter goes to the primer bulb and then to the carb. ... McCulloch MC1275 Steam Vacuum

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?

... Dyson DC25 Animal Bagless Upright Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?

... Oreck XL Ultra Bagged Upright Vacuum

Vacuum won't **** in upright position, but there is suction from the hose in the upright position

Theres a knob that switches it from floors to carpet turn the to floors.please leave feedback ... Vacuums

When I vacuum w/ the brush control in the on position it make a really loud noise, almost like a grinding sound. I have looked at it and nothing seems to be wrong, but I notice that the pin that engages the belt seems to vibrate a bit, possibly creating the noise. It started when I accidentally got part of a plastic grocery bag caught in the brush. Could it have stretched a belt? Nothing is caught any other place and it only makes the noise when the brush in in the on position.

Yes, the belt could have been stretched and is now vibrating and hitting other parts and creating a noise if much of the bag got caught under the belt. If you have another belt for this vacuum, please put it on and see if the noise stops. If it does ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis

U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The brush does not rotate at times. The belt is ok. It will not rotate in the stored position, but starts when I drop it to the other position, but not always!

... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Hoover Z 400 collapsible vacuum won't lock in the upright position. I pull the pin to change from a cannister to an upright, but the unit won't lock into position

This just happened to me. i took the vacuum completely apart and found that there is a locking plastic "tooth". this had snapped off but still it the track. the damage was bad but i was able to wash of all the lube off it and used a 2 part epoxy glue ... Hoover F5858-910 SteamVac Vacuum

My dyson shuts off when returned to upright position and it seems to be not sucking in the down position either

Hi its Darran at Dyson. I would recommend contacting our Helpline on 1866MYDYSON as one of our advisors will be able to run through some simple checks with you.Kind regardsDarranDyson Customer Liaison ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I need the fuel/gas mixture for a small (12") McCulloch Chain Saw. It has a 2.0 C.I.D. label with Fuel Mix I lnoted at the fuel cap. ja

The 2.0 CID is Cubic Inch Displacement, the size of your motor. As for fuel mixture, generally a 50:1 is a benchmark for this. Typically, it should be 1 gal. of gas for 2.56 oz. of two stroke oil. They sell pre-packaged, pre-measured oil at your loca ... McCulloch MC1275 Steam Vacuum

My Dyson Animal will not turn on when in upright position or when using the wand. It will, however, start when in the rug vacuuming position (leaned back).

... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hi I have an electrolux vacumm cleaner, super J model. My problem is that the powerhead only works if the switch is in the off position. vacumm motor works in the on position, opposite of each other. Can anyone help? Model 1401

Looks like there's an interchanged wires in your vacuum. Both the motor and the powerhead must go together. Check it up. Leave themotor wiring connection intact. Just tinker and check the powerheadwiring connection . ... Electrolux UltraLux 2000 Bagged Canister Vacuum

The handle will not click into the upright position-only stays in "vacuuming position". How do I fix it? Linda from KY

Go to www.dysonmedic.com scroll to bottom of page and click on "DC04 not positioning upright fix" for illustrated solution. The DC07 is similar. If this doesn't work, post a reply here and we'll see what else you might try.\015\012Good luck! ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Parking position i simply cannot figure out how to use the 'convenient parking position'.  Nothing seems to fit where the picture indicates it should.  Can anybody help me?

The parking position does not work with the EL5 (the big powerhead) It only works with the smaller version powerhead. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

The ON/OFF switch does not work. Unable to turn off vacuum without unplugging from wall. After removing handle, the ON/OFF switch is in ON position, but cannot be toggled to OFF position. Please assist. Thank you.

Replace the switch. Part number 28161067 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0263 seconds