Having problems with your Conair Vacuums ?

Conair does not sell the springs for their curling iron. Mine keep breaking and I do not want to keep buying a whole new curling iron just because the wire spring has broken. Instant Heat curling iron, model number CD8sWCS. Do you know where I can buy these springs or how I can improvise with something that will work almost as well?


Answers :

Hi,
\015\012
\015\012The best thing I know of is to take a wire bread bag tie....take the paper off of it so that you just have the wire part... twist this around the two ends of the wires where it broke...this will contect the two wires and ti should work again....only problem that I can see is that it may catch in your hair....folding the ends over tightly and crimping them with a pliers may help that out....
\015\012
\015\012I'm sure there is no replacement part available for that as they want to sell you a new one avery few months....hopefully this will get you a bit more time out of a broken one...
\015\012
\015\012heatman101
You will need to contact Conair at 1-800-326-6247 to order a replacement wire spring. Doing this will be cheaper then buying a new curling iron.
\015\012
\015\012http://www.conair.com/customer-service-cn-18.html
Repair Help & Product Troubleshooting for Conair Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Conair does not sell the springs for their curling iron. Mine keep breaking and I do not want to keep buying a whole new curling iron just because the wire spring has broken. Instant Heat curling iron, model number CD8sWCS. Do you know where I can buy these springs or how I can improvise with something that will work almost as well?


Hi,\015\012\015\012The best thing I know of is to take a wire bread bag tie....take the paper off of it so that you just have the wire part... twist this around the two ends of the wires where it broke...this will contect the two wires an ... Conair Vacuums

I have a InStyler (the rotating iron) by Tre Milano. This device is for styling hair. This is not a flat iron, but a cylinder that warms up and rotate's against a brush. It has 3 heat settings which works fine. Problem is cylinder has stopped rotating. My husband disassembled and believes the motor for the rotation has worn out? This is the question he had and mine is can it be replaced ? I have model number. . IS-1001 120v 60hz 135w. Conforms to UL STD. 89 0927-037875. Also stamped on the small


I'm repairing an Instyler right now. \012Troubleshooting, I connected a multimeter and measure the voltage where the motor is connected. When I push the button that makes spin it, I measure 12Vdc which is a correct value for that motor. Then I co ... Vacuums

I own a Hoover Steam Vac V2 deep cleaner with Auto Rinse feature. The Model Number is not available ex: was on the bottom of the machine and the sticker is completely worn off the machine. I am having a problem with the bottle you fill with detergent ex: this bottle is seperate from the main clean water tank. THE PROBLEM: The little plastic part that goes in the bottom of the bottle has an "O" ring ex: cone shaped with a spring.....it keeps falling out. Can you supply a part number for this


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=641300\015\012Generic problem for all Vacuums\015\012I own a Hoover Steam\015\012Posted by w_brennan on ... Vacuums

Hoover model u5753960 shows a photo on Sears Parts Direct of part number 42259027 (housing) with a separate spring and a separate screw. Does anyone know where those two parts are supposed to go ?


Hello there, as per the picture you posted in your last comment here is a schematic for the assembly of your unit. The part should be the main casing of the unit and ... Hoover U5753 Bagless Vacuum

I have a Simac Stirella No Problem steam generator iron Model no. SX8040D.I cannot control the steam generated.The button is stuck and so the steam is continuous and I am using a lot of distilled water.I have to keep on filling the tank very often I would like to send it for repairs but I do not have a contact number or address. Mohan [email protected]


... Vacuums

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.


On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.


... Kirby Vacuums

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have an IS222 Bernina Steam Iron that quit steaming today---the iron heats up but the steam switch doesn't light or heat. It appears that we needs a new steam switch. Can you furnish this?


... Vacuums

We bought a Philips Intellicare 8030 ironinng system in 2005. Two days ago water from the plastic water container does not go inside bigger water tank where we think the water gets heated up. When the heating tank is empty there is no steam that comes out of the iron. Also, there is water dripping off profusely from under the iron where the steam normally comes out. Can you please advise how we should remedy this problem Please advise which service centre in Sydney, Australia would we be able to


... Philips Vacuums

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.


... Panasonic Kenmore Canister Vacuum Vacuum

DZ9080 IRON IS NOT VERY OLD, BUT HAS HEATING AND STEAMING PROBLEMS. IT MAY BE ALL HEATING RELATED! MY WIFE WILL SOMETIMES JUST LEAVE IT "ON" FOR TWO HOURS AND THEN IT WILL START STEAMING AGAIN. I CANNOT MAKE SENSE OF THE HEATING INDICATORS; SOMETIMES IT WILL STAY GREEN NO MATTER WHERE YOU SET THE DIAL ---- AND IT DOES NOT FEEL HOT! WHEN I TRIED IT AGAIN TODAY, THE SHOT-OF-STEAM WORKED FOR A WHILE (AND THE SPRAY WORKED), BUT THEN ALL IT WOULD DO IS DRIP WATER AT THE TIP WHEN TIPPED DOWNWARD.


I couldn't find any warranty information on this iron, but I suspect that the heating element either has a faulty connection or part of it has cracked, making contact at time, but poor contact at other times. The unit will have to be taken apart an ... Rowenta Vacuums

My iron is dripping water my model number is dz6080 focus do i need a new one? It is coming out of the bottom when it is sitting upright. my ironing board is all stained and actually my floor is rusted from when I fold up my board and put it away it drips from the ironing board. I paid alot for this model.


... Rowenta Vacuums

The number 2 light is blinking and I can't get the machine to run. I know that when number 1 light blinks its because of the lid. What is the problem for the number 2 light on the island oasis machine?


... Vacuums

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'


Machine will not come on ... Kirby G6 Bagged Upright Vacuum

Owner/user manual Before my sister died she gave me the little grren machine model 1425 turbo brush with heat. That is all I know about it as she did not find the manual and now no one knows where it is and I really want to get it working and learn about it, as I know she loved it. so I really need a manual. thank any one that can tell me if it is on line or something.


Http://www.bissell.com/images/UserGuides/1400_206.pdf ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

My breville steam generator iron heats up but doesn't steam. I have only ironed 5 clothes with it.


... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.


... Vacuums

The foot pedal on my Kenmore upright vacuum cleaner has broken three times. The vacuum model number is 116.33923 and the Sear's part number is 8174906. Does Sears make this part in metal instead of plastic? It is becoming expensive to keep replacing this piece when it costs around $20 each time (including shipping) Thank you for your time. Jerry DeWulf


... Vacuums

After approximately 5 uses my Eureka 313A steamer will not heat. It has a green light so I know it is getting power. But it will not heat at all. Also, what is the warranty period?


The warranty is one year on this unit. It does sound like there is a problem with the power going to the heater on this unit, or the heater itself. If it is still under warranty, take it to the closest eureka dealer. ... Eureka 313A Stick Steam Cleaner

My swan steam generator iron s15040n is showing a push button when it is turned on. im pushing the button but it continues to say push and keeps beeping. the iron wont turn on at all. please help!!!!! thanks


... Vacuums

The wheels with the spring broke off and I'm trying to put a new one on but I don't know where the spring goes.


This spring can be very confusing to install. It slides onto the wheel assembly near where the attaching pin is longer ( there are flat protrusions on both sides of the wheel assembly). One end of the spring pushes up on the assembly when it is in pl ... Hoover Tempo Widepath Upright Vacuum - Blue

Jun 24, 2010 - Jun 24, 2010 - Needle not bent/ new needle not answer. I finally conclude that the entire bobbin case is ROTATING in its seat, which jams the needle. The "projection" is against the "spring" when I install it, but I can rotate the bobbin case PAST the spring without trying very hard. Bobbin case MIGHT get held in place better if it were closer to me (front of machine). I feel it is still not out from under needle plate as shown in diagram, but can't keep it closer to f


Hi,Your problem dated 24th June 2010 was re-posted today. If it has been already resolved, kindly ignore this message.Thanks for using FixYa ... Vacuums

How to wind cord onto spring loaded retractable cord reel for a Kenmore canister vacuum. There is a metal 'U' shaped, spring loaded, piece that fits over the outer aspect of the wheel. If cord needs to get wound on under this metal band I can't figure it out and the band is like factory sealed onto the wheel. Also. I don't know which direction to feed the cord onto the wheel


What is the exact model # please?Thanks!! ... Kenmore Vacuums

Why does my dyson slim dc18 keep shutting down, even though i keep it clean. Filters area is clean and all others have been properly blown out with air from a air compressor. It will work for about 5-10 minutes and then shuts down. Smells like ****, check the belt and a bit later it restarts again. It's seems to be almost over heating.


Maybe your motor is going. Here's a link to a site that talks about motor failure and replacement in a DC07 (not DC18). I don't know exactly what the odor smells like but maybe you can see if you have any of the other symptoms. Good luck! ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0631 seconds