Having problems with your Cordless sharp hand held ?

Brush starts and stops

Hand held portable shark cordless. Brush spins then stops

Answers :

Repair Help & Product Troubleshooting for Cordless sharp hand held

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Took Roomba apart to clean and now the pick up brushes start and stop during cleaning. The vaccum is clean but will not constantly spin. Runs great but pick up brushes start and stop. Is there a number for Roomba? Warranty? This one is less than one year old.


You can go to www.iRobot.com . This is the roomba website. You should be able to find replacement parts, customer support, videos or the Roomba product, and more.\015\012When y ... iRobot Roomba 530 Robotic Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.


Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

Brushes on hoover saavy start and stop, start and stop. Belt isn't broken.


... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Roomba My Scheduler started making a "grinding" noise every now and then until one day it just started grinding and then stopped (I could restart the unit, however it repeated the grinding and stopping). I have checked the wheels and all of the gears appear to be in good order. I have a hunch the brush motor may be stripped. Any opinions? Thanks: RAnderson


Hi!\015\012\015\012Further investigation (running diagnostics mode) revealed the impeller (in the dust bin) was out of whack. I got another dust bin from EBAY and replaced the impeller and motor. Unit works fine. ... iRobot Roomba 4210 Bagless Robotic Vacuum

I have a Hoover Windtunnel 2 upright vvacum cleaner. During regular use my wife turned it on and it staarted cleaning, then all of a sudden it stopped and then started again then stopped for good. I unclugged the hose, cleane4de the brushes , blew the main filer and still cannot get it to start. The motor seemed hotter than usual. Can you help me? Lenny Rentz e-mail [email protected]


Actually, if you don't have continuity, then you have an open, not a short. ... Vacuums

When i start the vacum the brushes trun for about 3-5 seconds then stops. the vacum still runs,its just the brushes stop turning, what should i do?


If your machine has no power or interrupted power, please check the following:\012 \012- Make sure the power cord is plugged into a functioning outlet to check for power.- The handle may not be installed properly, causing a ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

The brush motor starts and stops during use


Is it the actual motor stopping or the belt that spins the brush that's slipping? if its belt slip, this happens, pretty common on all belt vacs, dirt and dust gets under the belt and causes it to just slip with no actual grip on the brush end ... Hoover U8120-900 WindTunnel V2 Bagged Upright Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

The spin brush stopped working on my bissell proheat turbo. But they will start to spin when i shut it down and the motor has almost come to a stop.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Brushes stop rolling when against carpet, yes it is out of the upright position and when I left the base off the carpet the brushes start to roll again. What is wrong?


Your belt is stretched out so it just stops when the carpet resists it. Get a new belt made for your particular machine and you should be back up and running ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

5 yr. old Miele s514 Turbo plus's power nozzle brush seems to disengage temporarily, stopping the spin. Then it seems to re-seat itself after a few seconds, then starts spinning OK. I keep the nozzle brush very clean, so there is no hair or yucky stuff to cause it to jam. Please help.


I had a White Pearl with same problem. As I moved the hose/wand the brush motor would start stop. Find out where the circuit opens up by holding one part and moving the part that connects to it - 1) where the hose plugs into the cleaner, 2) the swi ... Miele S514 Solaris Turbo Plus Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.


Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Brushes stopped working and started making real sound sound


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40488&thid=754331\015\012Brushes stopped working and started making real...\015\012Posted by charlenemo on Jul 07, 2008 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

DYSON DC-15 TOTAL CARE ,BEATER BRUSH STARTS THEN STOPS,OVER AND OVER AGAIN?THOUGHT IT MIGHT BE THE SWITCHS,JUST REPLACED THEM,DIDNT WORK?ANY HELP GREATLY APPRECIATED.


Check your belt or maby something wraped around the end of the roller. ... Dyson Ball DC24 Bagless Upright Vacuum

We have a lindhaus central vacumn system. The carpet brush will start to rotate/spin, but then stops. I took it apart and ensured there was nothing wrapped around it...but it acts like it wants to spin, but doesnt.


... Lindhaus Vacuums

Model DC-31 Animal. Brand new out of the box. Brush turns intermittently at initial start-up then stops completely after 30 sec. to 1 minute of using. Belt is in-tact and functioning. Belt motor hand-turns with some resistance felt.


... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum

The cleaning brush turns only sporadically. It will turn when we first press the button but then stops and starts when we move the vacuum around.


Sorry to read about your problem, I hope this helps you out.you need a new belt, and or you have string or something jamming the brushI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

The brushes stop rotating on rugs after a few seconds then button has to be pressed to start rotating again but keeps cutting out


Not sure this is your foolproof solution to the problem, but you might give it a try to see if it solves your problem.\015\012\015\012When the beater brush starts to bind up due to debris it retards the action of the cleaner, sometimes to the p ... Dyson Vacuums

The motor works, suction is good, but the roller brush will not keep turning. It turns at start up, then stops a minute later.


... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum

Hoover Mach 6 stopped running and won't start up. Cleaned the brushes(roll freely) and checked for a clog but couldn't find any.


Ya okay how do you get to the motor. Then when you get to the motor are you soppose to guess what is wrong with it by just looking at it.. What kind of solution did you give this person? I'd say not a very good one. ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

My dyson DC04 started to **** a dog toy up the main bit with the brushes - stopped it immediately and removed the toy but since then the suction is still ok/strong with the extension hose picking up but no suction is getting to main scetion/brush area - sounds like a pipe is disconnected from the front area - nothing obvious on the surface....HELP! Thanks in anticipation........... Julie Price


Get a different brand vacuum. Dyson's are easily the worst vacuum I've ever owned. I've tried the DC14, DC25 and DC33 they are all heavy plastic POS's made in Malaysia. I've owned every kind of vacuum under the sun. Rainbow, Kirby, Oreck, Riccar, Seb ... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0704 seconds