Having problems with your Craftsman 17026 Wet/Dry Vacuum ?

How do I remove the filter from the 16 gallon 6.0 hp wet dry vac. Does the piece holding the filter on screw off or what?


Answers :

Repair Help & Product Troubleshooting for Craftsman 17026 Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I remove the filter from the 16 gallon 6.0 hp wet dry vac. Does the piece holding the filter on screw off or what?


... Craftsman 17026 Wet/Dry Vacuum

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a 6 gallon shop wet or dry vac. The dust and dirt comes out around the base of the motor fin, not around the tank top. Now what? Oh I lost the filter around the drum that holds the ball, so I wrapped a rag around it and made it secure. Respectively: TOM


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=765231\015\012Generic problem for all Vacuums\015\012I have a 6 gallon\015\012Posted by tsfroggy on Jul ... Vacuums

I have a stanley wet and dry vacuum 5.0 hp and 8 gallon should I have to take out the filter to use the wet vacuum


... Vacuums

I have an old 1.5 hp 10 gallon wet dry shop vac.do i have to have a special filter or can i make my own and can it burn up from not having the right filter?


... Vacuums

The brush does not rotate and the belt smokes. This is model VC-9230S-2. This is a bagless upright. I have removed the 4 screws that hold the bottom plastic piece on but it won't come off.


... Regina Vacuums

How do you remove the filter from Rigid wet dry vac?


Unscrew the 'tab/nut' at the BOTTOM of the filter and pull off the filter cartridge ... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

My Little Green Machine has stopped sucking (second one with this problem!) I have removed the bottom plate and cannot find how to get to the hose to determine if there is a blockage. How do I do this? There is a screw that seems to hold a piece in place but it does not come out to get access to the hose.


Remanufacturing is a big problem since we don't know what was changed and how. ... Bissell Vacuums

Newer wet dry shop vac ring that holds on filter continually falls off


... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

Rechargeable battery doesn't hold a charge very long. Is it possible to buy a new battery? What is the part number identification for the rechargeable batter for a Coleman Powermate 1 gallon wet dry vacuum? And where can I buy one? Philip Baker


... Coleman PMV6990 Wet/Dry Vacuum

Do i remove filter from wet dry vac to pick up water


... Ridgid 9 Gallon Wet/Dry Shop Vac 96882 Canister Vacuum

Trying to remove motor from wet-dry shop-vac.Remove all the screws,but doesn't seem to want to come out. Help!!


Hi Dan:I am not familiar with this model but some of the consumer wet vac models are build with a module and motor as one part. You will need to replace the entire module ... Craftsman Vacuums

It's brand new - just out of the box! Noticed the dirty water tank is bone dry. There is no suction! The front removable nozzle seems to be loosely attached.. The metal clip doesn't seem to hold it tight. Not sure if that is the problem. But I have a very wet rug! Suggestion?


It sounds as if it wasn't assembled correctly. Was it already put together when you purchased it? It sounds like the Brush Bar Belt never got put on.Let me know if you need more help.Jim ... Bissell 1950-3 Quicksteamer Plus Vacuum

Screw rusted; cannot remove


Nut, is attached to the motor ( armature) the plastic housing is a cheap replacement but the nut that is attached to the motor is not, crack the plastic housing (looks kinda grayish right) AND ATTACH A VICE TO ONE AND A NEEDLE VICE TO THE LOWER THIS ... Rainbow 75th Anniversary Canister Vacuum

I am trying to replace the belt on my bissell. The directions state "remove the screw that holds the red retainer in place, set red retainer arm and screw aside. I see the red retainer but can not get it out I also can not remove the black brush arm that holds the brush in place. I have tried and can not remove it.


Hi, Did you release the handle first before you flipped it over?Have you removed the screw and it still won't come out, or is it stuck even after the screw is out?Are you having trouble getting to it?Please r ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a Kenmore Progressive Canister Model # 29612992. I was replacing the sweeper bag, when I opened the lip, the plastic arms was pull out of joint and will not close. I removed the 2 screws under the lid to put back it in place but there I can't remove the plastic molding because there are still screws holding somewhere. Are there tabs instead of screws still hold the molding?


... Kenmore 25512/ 25513 Progressive Canister Vacuum

How to dismantle a Miele S 5980 vacuum cleaner. The RESET switch has fallen in and I can't remove the plastic panel to replace it. Neither can I remove the cleaner body to get in from beneath. I have removed 2 screws from the front of the barrel (nozzle end), one screw centre front, two screws towards rear, but there seems to be something else holding the housing together. [email protected]


... Miele Vacuums

I have a 5.5 HP 8 gallon Stanley Shop Vac with the cartridge filter. The book says I can use the cartridge filter which is a kind of paper to use for wet vac. It did not come with the foam filter for wet vac so I am wondering if I use it for wet vac will the cartridge break up?


... Vacuums

Flair S2220 Removed the four screws holding bottom cover but still unable to remove cover. Is there something else holding cover? The cover on the srew end will seperate but something appears to be holding cover on beater bar end.


Pop out the two little rollers underneath, at the front. you will find two little screws holding it on. Unfortunately, I found after I broke it off! ... Hoover S2220 Flair Bagless Upright Vacuum

We have several SGC-60D 1.5 Gal coffee urns and the front piece broke off. ( the tall rectangular piece that hold the tube on the front on) We've tried a couple of things but the new front piece won't connect to the screw to hold the tube on. Any suggestions?


... Vacuums

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.


If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon


Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

I have a hoover 3000 i have not used in awhile, and since I removed a large rug, I would like to use it again on my slate floor. HOWEVER, I cannot get it to pick up ANY water in the water recovery unit......it is dry, dry, dry. I have put in a new filter, cleaned the nozzle unit, the scrubber , and reconnected both the recovery unit and the water unit several times, but to no avail. I would like to get a graut attachment a well as replacement part, but since I can't get the basic unit to work, I


Have you made sure the plastic filter cover with the round hole in it that covers the filter is in place ( part # 59177096 ). This piece seems to get lost, and without it there is no pick-up. The other common problem is that the wheel assembly has be ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.2334 seconds