Having problems with your DeLonghi Vacuums ?

Looking for a vacuumhose nozzle for model Darel 1500W (DeLonghi). The plastic nozzle going from the hose is starting to break.

Answers :

Repair Help & Product Troubleshooting for DeLonghi Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Looking for a vacuumhose nozzle for model Darel 1500W (DeLonghi). The plastic nozzle going from the hose is starting to break.

... DeLonghi Vacuums

Hi, I have a cleanview bagless model# 3576-2 and my belt keeps breaking (it seems like one of the rings it should wrap around is missing) right now I have been wrapping it around the brush and a metal rod. Also, the dirt collected is going directly into the hose and not the bagless filter. What is going on?

... Bissell 3576 CleanView II Bagless Upright Vacuum

My Fantom Thunder upright has a blockage that sounds like it is directly above the dirt bin in the "head". I cannot access it from inside the bin chamber by going up the nozzle with a claw parts retriever. (This is the older model where the cyclone nozzle doesn't come off.) The wand, hose, rear inspection port, and front brush intake are all clear. How do I get the top of the vac off above the dirt bin? I don't see any screws or slots.

... LG Vacuums

Hoover SteamVac Model F6056-900 SteamVac/SpinScrub. Indicator light and high pitch suction noise indicates that dirty water tank is full. However, water level indicator (yellow bobbing plastic thing) is at the bottom of the tank and there is no water in the tank. Have check all the hoses for clogs, none found. Checked water port from motor area to receptacle tank for clogs, none found. Fixed broken hose to upholstery wand with duck tape, (wire not broken, just cracked plastic hose). The onl

There are 2 filters, make sure they are clean, one is on the tank lid, the other is from the bottom, it is red, pull it out and clean it. If yours has a foam filter on the tank lid covering the yellow ball, make sure there is at least a 1/4 in. gap ... Hoover Vacuums

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.

... Eureka 431A Optima Bagless Upright Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?

Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Shampoo-er This seems to be a common problem, the shampooer is putting out alot of water and hardly any suds. I read through the posts about the little filter that sometimes gets out of place and I think I found it in the box - is it about 1" diameter hard plastic ring around very fine mesh? If so where exactly does it go? Some posts say in the hose, and others say in the opening of the tank. Or does it go in the place where the hose attaches to the tray? I also found a round sponge in the box o

It goes on the small hole on the tank where the hose attaches to it. The sponge goes in the hole directly under the on/off valve. Here is a link to my online shampooer instructions.\015\012 \015\012 ... Kirby Ultimate G Bagged Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.

I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

There is something stuck in the handle of my Miele vacuum. I unscrewed all the screws hoping that I could remove the hard plastic handle from the hose. I was only able to flip up a piece of plastic where the switch is. Should I pull harder to pry the plastic apart? I was afraid I'd break something. Thank You, Chrissy

... Miele Vacuums

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg

Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

I have a Hoover windtunnel T series. Model #UH70105. The system check indicator was almost red so I cleaned the filter. There are no clogs and it vacuums fine without the hose, but when I go to use the hose there is very little suction and all the vacuum dust flys out of the end the hose piece fits into when not in use. Can you please tell me what is wrong?

... Hoover Vacuums

Scunci steamcanister model 52038 Steam does not get from canister through hose to nozzle. No apparent leaks - hose does not get warm. appears may be valve problem from canister to hose. Only used bottled water - barely used this machine.

... Scunci Vacuums

I have an old Miele canister vacuum and I do not know how to disassemble the hose to check for a clog. I think it sucked up a nerf ball the size of a ping pong ball. I changed the bag but it did isn't appear to be in the bag. The vacuum powers on but I do not have suction with the hose, and since the hose has hard plastic elbow joints I do not want to pry them apart and break it

Hi Emily: If you have the model number for your machine you may be able to find your manual on the Miele website. Check ... Miele Vacuums

The plastic coupler that hooks onto the propane tank cracked. There is a replacement part, coupler, regulator, Y hoses to the main and side burner, avail but how do you disconnect and re connect them? The hoses have a clamped metal ban attaching them to the burner tubes can't get them off. Thermos Barbecue Model # 461410707 Thanks much.

Wrong forum to help you out. ... Vacuums

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.

Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I replaced the motor in my 6500SR Epic vacuum cleaner. Now I have 3 clear plastic hoses for air flow. I know where two of them go, Im not sure where the third air hose goes? Jan

All three are connected to the control valve assembly.\015\012The long one goes through the hole in the bag container and to the door and inside.\015\012One goes to the bottom of the bag container.\015\012The last one goes to...I ca ... Electrolux Vacuums

I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?

... Easy Flo EF2300 Central System Vacuum

I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the

If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down

... Eureka Vacuums

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Electrical cord electric cord connection to cannister boby on filter queen is fixed by a plastic grommet or connection - how does this go into place without breaking or forcing plastic part?

It has a **** shell like closure on the inside and can normally be popped out by squeezing with pliers. It will have a slightly oval appearance, you must squeeze it round and pull. ... Filter Queen Majestic Canister Vacuum

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped

... Electrolux Guardian Bagged Canister Vacuum

Hello, I have the same model. And though it is three years old, starting from the last month, it does not clean anything anymore. Cannot even pick up one single thing from the floor. Every dirt gets stuck in the hose. I cleaned the hose and cleaned the filters but it still does not pick anything up. Is three years its normal lifetime or do I have the change the filters, instead of cleaning them? Thanks.

I know bissell vacuums are very cheap but they should last more than 3 years. there should be two parts to the dirt cup. remove the dirt cup and above it there should be a round plastic part. unscrew it and check that filter. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce

I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

Rainbow shampooer The soap dispenser on my Rainbow is not dispensing soap when I flip the switch to 'soap' mode. All connections are intact. All plastic hoses are intact. What do you think is going on? The soap bottle connects to a little straw that appears to be free of obstruction, however, it connects into a sealed casing on the hose.

The little "wash/rinse" switch on some of the Aquamate units shuts off the soap flow by kinking the tube inside the housing. If you leave the switch in the rinse position (therefore, kinked) when you're done using it, it may dry in the kinked positi ... Rainbow E series Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0896 seconds