Having problems with your Dewalt DC500 Canister Wet/Dry Vacuum ?

I have a dewalt cordless/corded shop vac and it works fine with a new battery installed. When I plug it in it does not work. I took it apart and saw that the cord goes straight to a circuit board and is beyond me to troubleshoot. Has anyone had this problem before?


Answers :

Repair Help & Product Troubleshooting for Dewalt DC500 Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a dewalt cordless/corded shop vac and it works fine with a new battery installed. When I plug it in it does not work. I took it apart and saw that the cord goes straight to a circuit board and is beyond me to troubleshoot. Has anyone had this problem before?


... Dewalt DC500 Canister Wet/Dry Vacuum

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

I fear the motor has failed on my Electrolux Oxygen EL6988D. Just six months after the warranty expired, I was vacuuming when it suddenly stopped. There was no blockage in the tube and it wasn't working hard or long . . . it just stopped. I looked around the Internet and it appeared that many similar Electrolux units have a fuse. I hoped my problem might just be a blown fuse, so I took the machine apart. There are two small printed circuit boards, but no fuse. There is an in-line


Hi,\015\012\015\012I don't think you need a new motor, but please stop testing the machine with live power. It's dangerous and unnecessary. Your tests indicate to me that the motor is fine and your thermal-fuse - I think this is wh ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering


Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

Meile vacuum S4210 seems to have a circuit board problem


... Miele S 4210 Bagged Canister Vacuum

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?


Probably needs a new hose. ... Vacuums

S444i just would not switch on. When I took it apart I sprung the rewind coil on the cord retracter and I can't get it back together. Now I have 2 problems!! It won't start and the rewinder


... Miele Vacuums

No power. I was getting intermittent power with my miele s558 midsize canister, but it was predicated with me fiddling with the retractable cord to get it to come on and then not move the canister while I was vacuuming. Now I can get no power. I have taken it apart and can see no issues with connectors, cord, casings, etc. It all looks fine. It is about 5 years old and I have had no problems with it.


... Miele S558 Red Velvet Bagged Canister Vacuum

The retractable cord is stuck all the way out and will not go back in. Is there a simple way to fix this "disaster"??? without taking vacuum apart that is. And this is not my exact vacuum but I figure the cord problem would go for all of them. Ours is a ORANGE HEPA 360 Kenmore Whisper Belt 12 amp with PowerMate Model # 116.29219800


... Kenmore 27915 Bagged Canister Vacuum

I have a similar problem as many do with this model, "clean Roomba's brushes".. We took it apart last night, cleaned out all of the dust we saw. we removed the cover, the housing for the brushes and everything else we could. Still has the same problem. What now?


Mine did the same thing and no mater how much I cleaned the brush or pulled fibers of the ends it did not stop until I:Removed the little yellow tabs on the ends of both brushes and used a tooth pic to remove the built up inside the bearing ass ... iRobot Roomba 530 Robotic Vacuum

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

Miele S318i worked ok till I took it apart to blow really fine ceiling "popcorn" dust that got sucked by the filters. When I plugged back in started for a milli second and quit. At this point I believe the circuit board might be the fault, but I want to test motor before I go and buy the part. Can I simply run 110 to the two moter contacts to bench test? Steve


Yes, you can. ... Miele S318 Bagged Canister Vacuum

Our vac unit is 1 1/2 yrs old. It will not shut off, I've tryed your problem solver by hitting the unit with a hammer. I'm an electrician I was surprise by this advice but never the less I did it and it doesn't turn off. The model # E130J I believe it's the printed circuit board, please advise Thanks Doug


Your machine is still under warranty if you purchased it new (5 years). Take it to the shop you purchased it from (Aerus Electrolux), or call them for free pick up, and ask them to repair it. The boards do go bad occassionally. It could also be t ... Electrolux Centralux Vacuum

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it


It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

My Renny brush is not moving what do I do? I just had is serviced for $200 and brought it back once already, he is claiming now that it is the circuit board. I do not trust him to fix the problem, can I fix it myself? It also now is not shuting off.


You have two circuit boards in th Renny, one is in the handle of the hose and the other is called a triac located next to the motor in the canister. There is a long and drawn out procedure in trouble shooting the problems with the Renny and if you do ... Electrolux Vacuums

Our Hoover U8172-900 brush motor is not working. Do you have a wiring diagram so I can determine if the motor circuit board is the problem or the motor?


No diagrram is necessary unless you have dismandled.\012Check if the brushes are touching the mtor commutator. If not you can easily remove both the brushes and polish the surface evenly .Insert only after cleaning the motor commutator till the ... Hoover Vacuums

No Power Nothing happens when I push the power button. We've taken off the covers and found that there's a circuit board. Any suggestions on how to fix this problem. Thanks C


... Miele S 4210 Bagged Canister Vacuum

Hi I have a eureka 410 series lightweight upright and I took it apart to clean the dust from inside and on the very bottom of the handle the is a metal clip and a white straight plastic peice that fell out and I dont know how it goes back in.


... Eureka Whirlwind 410 Bagless Upright Cyclonic Vacuum

If the circuit board has a problem can it be fixed?


Don't know what circ. board your are talking about, but usually they get replaced and not repaired. ... Vacuums

Took canister apart to replace power cord. some grid fell out before i could see where it was. need to know where it goes


... Oreck BB2000 XL Little Hero Canister Vacuum

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a


Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Vacuum won't switch on;got it apart;cord ok;need wiring diagram


Its a great idea to write on paper how its connected . So it helps with dis assembly & reassembly . I tried a Internet search . Looks like it'd cost money for a service manual. Though. I found a Kirby Spares Website that could help. Although it d ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0707 seconds