Having problems with your Dirt Devil bagless ?

How do I install adjust wheels on

Fell off while changing belt

Answers :

Repair Help & Product Troubleshooting for Dirt Devil bagless

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a


The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Have a dirt devil breeze that the adjust. wheels fell off while replacing the beatter brush. can't figure out how to put the wheels back on


... Dirt Devil Breeze Bagless VacuumVacuum

How do I install the front wheels on a kirby sentria G10D? One of the front wheels broke completely off so I ordered the front wheel shaft assy but I didn't remove the broken one so I am having difficulty with how to put the new one on.


... RTO Vacuums

Lower wheels for low carpet pet lover cannot lower inside wheels to replace adjustment knob


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Re-attaching spring for wheel height adjustment


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I replaced the agitator bar drive belt on a Hoover Model U6432-900 upright vacuum cleaner, but it just slips when the drive wheel is spinning. Is there an adjustment I need to make? I don't see any adjustment spots.


You probably should have replaced the flat belt(38528035) also. But the drive belt has a idler wheel(#13) to engage it, is it riding on the belt, if not if may have jammed to one side and able to spring up against the V belt. It could have broke al ... Vacuums

The right front wheel came off my G6 Kirby vacuum, then the entire axle and wheel adjustment came loose--including a spring that was attached to something.


Thank heavens for a husband who can fix anything--and save me a lot of money for repairs and advice! ... Kirby Vacuums

HOW DO I REPLACE MY REAR WHEELS ON MY KIRBY G6...I WAS ABLE TO TAKE IT OFF BUT NOW WHEN I INSTALL ONE THE DRIVE SHAFT IS TOO SHORT TO INSTALL THE OTHERE??? PLEASE HELP


Try equalizing the space between the two wheels and the drive shaft. If it's not equal, they may not fit properly, or at all. ... Kirby Vacuums

The pile adjustment wheel on my Sebo X4 has come off; I ordered a new wheel thinking that it would come with the PIN/AXLE but it doesnt. What do I need to order noe? I cant seem to find the pin as a spare part. Dp I need to order a servo motor? Many thanks Hannah


... Sebo X4 Bagged Upright Vacuum

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

I need a nozzle adjustment lever and cam kit for a Hoover upright U5432-900. This the part that adjusts the front wheels for different types of flooring.


... Hoover U5432-900 WindTunnel Plus Bagged Upright Vacuum

Dirt Devil Vison Bagless Upright- adjustment wheels will not stay in position


... Vacuums

Installation of front wheel assembley on a hoover vacuum


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Replacing spring in wheel height adjustment


I just solved the problem. Go to this website: http://www.completevac.com/kirby_schemo_5.htmlIt will show you where the spring goes (left side inside the ratchet - when you remove the ratchet you will see that it is hollow. That's where the s ... Kirby G6 Bagged Upright Vacuum

Install hoover vacuum wheel assembly


... Hoover Vacuums

How do I install height adjust cable on roomba 415?


... iRobot 4150 Roomba Vacuum

How to replace a wheel heigth adjustment to my dirt devil breeze 12amp


... Dirt Devil R088100 Breeze Bagless Upright Vacuum with On Board Cleaning Tools, 12AMP, 13" Nozzle - Refurb

HOW TO INSTALL A WHEEL STOP ON A KENMORE PROGRESSIVE


... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

HOOVER U4257-930 BELT INSTALL


... Vacuums

I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How do you install the torsion spring onto the front wheel unit of a Hoover vacuum, model U5760-910? Thanks!


Is this what you're looking for? Also,the manual for your vacuum is available online at http://www.hoover.com/CustomerService/Manuals/Default.a ... Hoover Vacuums

I'm installing a new ignition module on a bc24w weedeater trimmer--the part has 2 screws holding it on-it is apparently adjustable--what gap setting should I use between it and the magnet (armature & rotor??) Also what is proper spark plug gap? Thanks


I usually use a match book cover between it and the magnet. this way the gap is about right and it will not hang on the magnets. put through both sides at once, then push it in and tighten it up. then take out guage. spark plug gap is .025, the armat ... Vacuums

Bought today a used rca rp3721a clock radio without the manual. need user manual to adjust all the settings, for example TIME, ALARM TIME, ALARM ON AND OFF, radio or "beeper" alarm on, entire unit on and off without unplugging it from shore power,and anything I haven't thought of up to here. The unit is RCA Model RP3721A clock radio, and appears to be functional. Our problem seems to be "the nut behind the wheel". e-mail: [email protected]


Hello,I advice you check the links below to search for the\015\012manual of your device, the link contain almost virtually all the manuals of all \015\012device.manualsonline.comORmanualnguide.com ... Vacuums

How to install front wheel assembly on Hoover Bagless windtunnel vaccuum


There is a spot that sticks up on the holder for the wheels, the hole in the spring goes there, then it fits between the holder and the base asm. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover Elite how to connect front wheel assembly to height adjustment knob


... Hoover Elite U5061-900 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0327 seconds