Having problems with your Dirt Devil Breeze Bagless VacuumVacuum ?

After changed the belt, it feel very heavy, have to push hard for it to move


Answers :

Hi have you tried changing the pile setting ( if it has one ) or your belt maybe a faulty one causing it to be to tight . Always use genuine parts because they are made exactly to the right fit for your vacuum. Fake or pattern parts are not made properly. Hope it helps. Richard :)
Repair Help & Product Troubleshooting for Dirt Devil Breeze Bagless VacuumVacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After changed the belt, it feel very heavy, have to push hard for it to move


Hi have you tried changing the pile setting ( if it has one ) or your belt maybe a faulty one causing it to be to tight . Always use genuine parts because they are made exactly to the right fit for your vacuum. Fake or pattern parts are not made prop ... Dirt Devil Breeze Bagless VacuumVacuum

I have the bagless hoover windtunnel and it doesn't pick up anything and it is very hard to push. Changed the belt and The rollers are spinning and the filter has been changed. What else can I do?


It sounds like there are dirt and hair wound around the wheel axels cousing them not to spin freely. You have to remove all hair and carpet fiber. Then drop a drop of lubricant oil on the axel.\015\012Change the filter.\015\012You should ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a dirt devil featherlite plus and all of the sudden it started pushing hard and smells hot. I cleaned the roller, changed the bag, checked the belt. The belt is a little wore, but not bad.


If it is pushing hard then you still have a belt problem. It may not be broken but the belt is stretched out too long and will not turn the roller brush fast enough to make it push easy. ... Dirt Devil M085500 Featherlite Plus Bagged Upright Vacuum

We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after


... Vacuums

Why is my oreck upright hard to push on rugs- do i need to change the belt?


... Oreck XL2200 Bagged Upright Vacuum

After changing the bag on my riccar it is very hard to push'


After putting a clean bag into the vacuum cleaner, more air can get through it, so it generates more vacuum, sp it is obvious, that it will be harder to push for some time. if it wont get better, it only means you didnt gt it with a clean airbag ... Riccar 8955 Upright Vacuum

Changing belt while changing the brush belt the cog/gear fell out, ive tried to push it back it but it doesnt seem to stay...is there a way to snap it back in or is the unit broke?


You will have to replace it, and it comes on the pump not separate. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Dyson DC07 has recently been service and was making a clattering noise and very hard to push. We have taken it back and he has changed the clutch mechanism under the base which has solved the clattering, but it is still really hard to push because of the suction. It is even lifting the carpet in one room. Can you tell me what the possible reasons for this could be? One thought we had was that the little rubber wheels on the bottom cover could have worn so the hoover is closer to the floor


On the sole plate you should have 5 little wheels, these are prone to jamming after a while. You should make sure these are not jammed in anyway.\012\012You can release these with a screwdriver, but be careful not to prize too hard as you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to change the belt for kenmore heavy duty plus extra wide sweep model no. is 1163966180 looking for manual how to change the belt


... Vacuums

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Vax 2300 vax v-2300 brush is not turning so changed belt snapped as soon as i put hoover on and getting burning smell put another belt on same again and brushes still not moving only 4 months old


If the roller brush cannot be rotated easily by hand, it is likely that debris is jammed inside the end caps.Make note of the direction arrows on the end caps as you remove the roller brush. You will need to know this for reinstallation. The end caps ... Vacuums

My Windsor Versamatic plus has all of the sudden become very hard to push. I maintain this vaccum very well. It picks up fine, just to heavy tp push apparently


Likely the wheels are frozen with thread and hair at the sides of the wheels. Check for free movement of each wheel and pick out the debris around any that are hard to turn. Long needles and tweezers are good tools for this. ... Vacuums

When we changed the belt the new belt broke right away and the brush roller wouldn't spin. My husband cleaned off the roller and got it moving slowly again, but when we went to re-attach everythin


The thing you call wheels are actually called roller bearings that fit at both ends of the brush-roll there probably seized up you can get a new brush-roll with bearings from the link below. ... Dirt Devil Breeze Bagged Upright

I have an oreck xl and the vaccum wont hardly push. Is it the belt? The brushes aren't turning when I lay it on it side. How do you replace the belt? If you can give detailed instructions I would so appreicate it . Thanks


On the side of the head you'll see a removable plate with one screw. Remove the screw and slide the plate towards the front until it's off. You'll see the belt. ... Oreck XL21 Bagged Upright Vacuum

My Bissell Proheat 12 amp is hard to push forward(whether on or off). There is a loud clicking noise when pushing forward and it ''jumps'' up on every loud click. It's OK when pulling backwards, sprays and vacuums up water. Belt appears OK. Thanks


I had this same problem and here is what solved it for me. On a previous cleaning session, my wife decided to take the two front screws out of the clear plastic shroud that covers the brushes in order to clean behind it. Upon re-installation, she did ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Cleaner stopped working, changed bag still not working. Have checked mains fuse and liittle fuse on printed circuit board. When cleaner is on moving slider to the off positon the LED's glow red for a fraction of a second. Reset button does not feel as though it clicks when pressed, it does not seem to move. Many thanks, Hugh


... Panasonic MC-E583 Bagged Upright Vacuum

I think i need to change the belt on my vacuum, there seems to be a loss of suction when pushing the vacuum. Where can I get one and how do I change it?


How do I fix a broken belt on my vacum ... Eureka 4700A Maxima Bagless Upright Vacuum

I've had my Dyson DC14 vacuum cleaner now for approximately 9 months and been very happy with my purchase. However, It is used sparingly maybe twice a week at the very most. The problem is when I try to use the item on my carpet, you have to push really hard to get it to move. It's as though the suction power is far to strong. It certainly doesn't glide as I think it should. It still picks up as usual but I cannot imagine that having to 'force' the machine to move is the normal operating procedu


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?


It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.


Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

How to change the vacuum belt on a kenmore heavy duty plus model number 203966180


... Kenmore Vacuums

DCo7 too much suction hard to push


This suggests that the bristles on your brush roller are worn out.  When the bristles are a good working length, rotation of the roller actually helps to pull the machine over the carpet. When the bristles wear down this effect is lost. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0761 seconds