Having problems with your Dirt Devil Featherlight Bagless Upright Vacuum ?

Operating Question Where is the switch to switch from the floor to wand mode on the Featherlight bagless model? Thanks.

Answers :

There isn't one. The wand is always active, because it is the only air inlet on that machine. When it's plugged into the side of the machine, it's pulling dirt from the nozzle. When you pull it out, it just functions as hose attachment.
Repair Help & Product Troubleshooting for Dirt Devil Featherlight Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Operating Question Where is the switch to switch from the floor to wand mode on the Featherlight bagless model? Thanks.

There isn't one. The wand is always active, because it is the only air inlet on that machine. When it's plugged into the side of the machine, it's pulling dirt from the nozzle. When you pull it out, it just functions as hose attachment. \015\01 ... Dirt Devil Featherlight Bagless Upright Vacuum

I have a model F602-900 and it show it is in the tool mode. How do I get it to change to the floor Mode?

... Hoover F6020-900 SteamVac Upright Vacuum

I have a dirt devil featherlite bagless vacuum; model #088600. It has suction through the hose but not through the floor mode. I think there is a blockage in the hose area but cannot seem to take it apart enough to find it.

There are 3 screws 2 on the left side behind the hose and 1 on the right back by the wheel.that will take the cover off.if you need to get into the bottom there is a screw on the bottom plate in the area where it looks like the belt travels.is the br ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

My dyson slim vacuum doesn't switch from hose to floor mode. I thought the foot lever was broken. I realigned it but it doesn't switch now from floor mode to hose mode. I take out the hose and I can see the white part. I thought it should move as you go from upright to recline position of the handle.

The changeover valve is not activating - call the Dyson helpline - they'll set you up for a repair with a repair dealer in your area. ... Dyson Slim DC18 All Floors HEPA Bagless Upright Vacuum - Iron/Titanium/Yellow

Just got my dc33... one issue... the dial switch to control btn bare floor / carpet mode doesn't seem holding in it's position when I set to the bare floor mode... it keeps coming back to carpet mode with brush-bar activated... the dial doesn't really click to the floor mode. Any advice on this?

Hi there,I'm sorry to hear you're having difficulties with your DC33. If you're concerned that the brush control doesn't seem to be staying in position, it's probably best if you get in touch with us directly. One of our experts will be h ... Dyson DC33 Bagged Upright Vacuum

Can't switch cleaning mode from tool to floor

There's a mechanism inside the steamvac that should switch the mode automatically when you press the handle release and pull the handle down for the vacuum mode... it's automatic! it took so long to figure out because I kept looking for the switch wh ... Vacuums

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

We recently bought a home with a 52" Hampton Bay Berlini Model 729 395 ceiling fan with a light that operates on a remote control. There is also a wall switch plate with two circular controls - one pushes and spins, the other turns with 4 clicks. We can not get the light or the fan to operate using either the switches or the remote. We have checked the circuit breaker. The manual that came with the unit - provided to us from the previous homeowner - really only describes how to install the uni

Nancy do you want to sell the Berlini fan if youstillo have it? ... Vacuums

Switching suction mode?

That unit is supposed to automatically do it when you lock it into the upright position. When you do that you should immediately feel suction at the hose/handle. If you don't, you are probably either missing your U-bend Assembly or the valve that swi ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Dyson DC07 bagless - upright mode v poor suction, wand mode ok

I suffered with a serviced but not sucking DC07, its fixed now. How? By replacing the cyclone unit via anotherbay, it was an accumulation of dust and debris in the section that is not accessible. Borrow a working cyclone if you can and check the diff ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Blocked suction The FLOOR suction line (Hose) is clogged. I Can vaceum the floor, but it will not pick up anything because the hose to the bagless canister is blocked. I can switch from floor to hose and can vaceum furniture. it will not pick up off the floor. I have tried running a wire down/up the hose. I Can feel the blockage, but I cannot get it out. I am afraid to pull the flem hose out as I do not know how it is attached at each end.

Hi,Here is a tip that I wrote about my Bissel ... the hose should just pull out... it is just stuck in there tightly...\015\012Bissell Bagless Upright Vacuum ... Royal 088500 Featherlite Upright Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope

Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

I have a model u6476 self propelled hoover.The switch will not turn or off all of the time.The plastic slide does not operate the switch but slides over it.The switch seems to work easy enough by hand.Cleaner was purchased 2-23-07 Any iseas?

If the rod isn't pushing the switch, then something inside the handle asm. broke and isn't holding the rod in place. More often then not, it is the switch, but could be the rod in this case. ... Vacuums

For a dyson manual for the floor model dc24 - Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

User manuals can be downloaded from www.dyson.com but Dyson service manuals are apparently unavailable anywhere. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Windtunnel bagless vaccum model uh6000 on/off switch no longer working, must plug/unplug unit to use. Can switch be replaced?

Hi, \015\012\015\012Yes they can be replaced and are relatively easy to fit. In my opinion, Hoover are one of the best vacuum manufacturers when it comes to obtaining spares and you should have no problem getting one. I did a (very quick) ... Hoover Vacuums

No suction below when carpet mode or bare floor mode selected Lots of suction with wand

It is probably clogged near where the floor part picks upthat is why the wand still works ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Kenmore Progressive with direct drive model 116.36923502 stopped picking up debris and empted it into the floor and is there something you need to do to switch from floor to using the hose. It does not have any suction.

Sounds like you have a clog in your hose, full bag, or dirty filters. take the bag door off and feel inside at the bottom for suction or air movement. if you have suction there chances are its a clog in the hose. You can use a coat hanger or somethin ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The vacuum works on carpet mode but not floor and only when the wand is attached to the floor brush otherwise it does not work at all

Please define "works" on carpet mode" do you mean when you say it does not work at all, that it does not run, or does not have suction. This sounds like the symptom of a clogged hose with blockage like this another vac needs to be used to draw ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Wand will not come on electrical switch will not activte on floor vacuum wand

Just replace the switch. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

I am looking for a switch for a Hoover floor polisher model 0211. Thsi model is about 50 years old.

Generic problem for all Vacuums\015\012I am looking for a\015\012posted by csoper on Apr 18, 2008\015\012Report abuse\015\012 ... Vacuums

I have a Hoover WindTunnel Bagless Vacuum Cleaner, Model #U5753-900, Serial number 110600215585, which I purchased from Loew's on 3/31/07. With it, came a Hoove Slider for hard floor surfaces, Model #S2105, Serial number 050500084989. The Slider strted making a noise--I thought something had been caught in the roller, but discovered, it had not; so I and my husband proceeded to take the Slider apart. I believe one of the belts had come off; but when we took the screws off the bottom to check

... Vacuums

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless

Get over it and buy a new one!!! ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0872 seconds