Having problems with your Dirt Devil Featherlite Bagless Vacuum M085845Vacuum ?

Twirly thing under the vacuum has stopped spinning

\015 Purpose for Pets Dirt Devil. Out of nowhere the twirly brush thing in the beater bar no longer turns. There is still suction, and when I push the second power button (on the head of the floor attachment) the motor or whatever it's called starts up and it sound fine, but no action. The cords aren't loose or anything. It has worked like a champ for almost a year. Can you help?\015

Answers :

There is a belt that drives the beater brush. flip the unit over, you can remove the bottom cover by removing a couple of screws. to one side of the brush you will see a channel where the belt should be. go to you local walmart, sears or hardware store and in the vaccume section they will have belts, on each bag of belts will be a list of vaccumes that belt fits simply find yours. with the new belt simply lift the beater brush out at the belt channel side and install the belt around motor shaft and brush. then place brush back in place , be suer brush guides are in properly. this should do ya.
Repair Help & Product Troubleshooting for Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Twirly thing under the vacuum has stopped spinning


There is a belt that drives the beater brush. flip the unit over, you can remove the bottom cover by removing a couple of screws. to one side of the brush you will see a channel where the belt should be. go to you local walmart, sears or hardware sto ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

I was vacuuming, and ran over an area rug with those tassle things on the end. the brush immediately stopped spinning. so i turned the vacuum off and un-tangled the brush. after replacing the brush and putting the assembly back together, the brush no longer rotates.


Did you smell something burning? You probably melted/broke the drive belt. ... Dyson Ball DC24 Bagless Upright Vacuum

I have a Bissell Pro Heat 2X carpet cleaner and the brushes spin, then stop. I turn it off and when I re-start, the brushes do not spin until I push foreward. The it spins and stops again. Both belts are tight. The brushes spin if held above the carpet, but upon contact with carpet it stops. Same thing on a hard surface.


The reason for the brushes to stop when it is above any surface is there is a switch in the handle that stops the brushes so it dont burn your motor up it may have a faulty switch. ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

My oreck vacuum has stopped sucking up things.


It won't turn the brush because the belt is stretched or broke from the heat of sucking something too big up. If you have your service manual it should show you the location of the belt covers to replace it. ... Montgomery Ward Oreck XL Celoc Hypo-Allergenic Vacuum Vacuum

I have the bissell powerglide vacuum with the turbo brush attachment. Being the neighborhood "cat lady", I love this attachment -- that is, I did until it just stopped spinning. I don't see anything blocking the brush. It just doesn't spin when I attach it to the vacuum hose.


1. this could be (2) things that are happening or 32. there is hair surround the spindle (rotation) brush tool blocking rotation or you have a motor that has failed and it is not turning the rotation brush.3. the switch (on /off) has fail ... Vacuums

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the


Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

Brushes spin and stop spinning - Panasonic Kenmore Canister Vacuum Vacuum


... Panasonic Kenmore Canister Vacuum Vacuum

Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.


The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums

Dyson D25 I was vacuuming and got the cord tangled inside the vacuum dyson 25. We opened it and was able to remove the cord. But the brush stopped spinning when I use the vacuum.


Hi there,Your DC25 is equipped with a sensor which shuts off the brushbar if something jams it. Please follow the steps shown in the video below to reset the machine after checking for any remaining obstructions. You may also want to refer to ... Dyson Ball DC24 Bagless Upright Vacuum

My hoover spin scrub brushes stopped spinning and i have cleaned intake filter and tried to turn the thing that spins it...when brushes are off the hole turns then as soon as i connect brushes the brushes will not turn what else can i do!!???


... Vacuums

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

Dyson dc 39 brush stops spinning when vacuuming


... Dyson DC39 Animal canister vacuum cleaner

Sweeping part of the vacuum stopped spinning.


Is the belt stretched or broken? There needs to be a (not-stretched and not broken) belt connecting the rotating brush (agitator) to the motor pulley on the vacuum. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The vacuum turns on, but the thing with the bristles doesn't spin. Help?


No it can't be bypassed the motor is dc.the circuit board converts it from ac to dc ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Same thing, brushes dont spin unless vacuum is tilted back


I had the same problem. Checked the belt, pulled out all the hairs, cleaned the hoses, but the agitator brush wouldn't spin at all or only marginally. Finally I removed the agitator brush altogether and found crud and accumulated in the small groov ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

The spinning brush just stopped spinning. This vacuum is only a few months old. Please help!!!


Hello. The very common reason this happens is that the belt that drives the brush breaks. The fix is to get a new belt and install it. Do not get a generic belt, get an original equipment belt from a vacuum cleaner store. ... Vacuums

The vacuum spins around on the spot left to right and continues to spin for a couple of minuted then stops


\015\012\015\012\015\012Your bump sensors are malfunctioning... I had the same problem. The best thing to do is order a repair kit. I ordered mine from EESolutions.ca and it worked great. ... iRobot Roomba 530 Robotic Vacuum

I have a Hoover spin vac # 7410-900 the brushes don't spin but i can hear the pump running , checked the brush block stem thats fine the unit feeds water and soap. but i have no vacuu.me or brush movement getting ready to rip the turbine out to check it . the weird thing is it worked fine and then just stopped


... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

My Hoover spin/scrub floor cleaner has stopped scrubbing- the brushes spin for a few seconds right after turning it on, then stop until I turn it off and then on again. How can I fix this? I do not have a lot of money. I have taken off and cleaned the brushes and bottom vacuum opening.


Hi giacoma11,The common cause for this problem is the belt of your vacuum. It could be that the belt came loose or already worn out and needs replacement. To check if the belt is loose all you need to do is unscrew the bottom of the vacuu ... Hoover H3060 FloorMate SpinScrub 800 Upright Wet/Dry Vacuum

My bissel 310-3150 will not dispense cleaning solution, hence it will not suction up water. Red spinny thing will spin a couple of revolutions, then quit. When that stops, everything stops. What can I do to fix this? Unemployed so repair shop is out. DIY fix is needed.


... Bissell 1693 PowerSteamer Upright Vacuum

Just started to use the vacuum and it just stopped.. no blown fuse/ the round thing on the bottom is running freely - don't know what happened... vacuum is appox 5 years old


Check the carbon brushes of the motor, the switch, a disconected wire, the main cord ... Rainbow E series Canister Wet/Dry Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance


... Kenmore 34722 Grab-N-Go Upright Vacuum

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?


... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0911 seconds