Having problems with your Dirt Devil Featherlite Bagless Vacuum M085845Vacuum ?

I placed the new belt on the brush roller like i was suppose to, but brush roller will not turn forward or backward. What am I doing wrong?

Answers :

Most likely the roller is frozen due to dirt and debris.\015\012Follow the instructions to remove the belt and roller.\015\012Clean the roller as best you can and at each end where the hard rubber holders are located. Add some WD40 between the brush and these holders and turn by hand until the holders move freely around the brush.\015\012Reassemble making sure the belt is on in the correct manner so the brush rotates in the proper direction.
Repair Help & Product Troubleshooting for Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I placed the new belt on the brush roller like i was suppose to, but brush roller will not turn forward or backward. What am I doing wrong?

Most likely the roller is frozen due to dirt and debris.\015\012Follow the instructions to remove the belt and roller.\015\012Clean the roller as best you can and at each end where the hard rubber holders are located. Add some WD40 between the brush ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Eureka Boss 4870 -Brush roller won't turn on carpet and turns when its not supposed to (with handle in upright postion). New belt had burning rubber smell right away.

... Vacuums

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.

You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?

... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

A cap on one end of the roller brush is centered and turns freely. The one on the other end is not centered and does not turn but does not look broken. It looks like it's supposed to be that way but it doesn't allow the roller brush to turn. How to I solve this?

It's hard to say definitively what the problem is here. Rollers usually have bearings at each end and they can wear or freeze up especially if they are exposed to water. When you say that the cap is not centered, I assume that you mean that you hav ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]

Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I have a Kirby G series diamond edition. There seems to be no suction when I turn on the vaccum. The bag inflates, but the roller does not turn. It has a new belt and the roller brush is clean. Any suggestion on what I might do to increase the suction and get the roller bar moving?


My oreck roller brush does not turn, belt is new and attached properly help

... Oreck Vacuums

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?

This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

Runs but doesn't vacuum/****. Sidebrush works fine. Cleaned the roller brushes, and that seemed to confuse the robot and now it keeps going backward a few inches, turning, and then starts going backward again.

Sounds like a sensor problem. pull and clean the front black/white caster assembly and the revealed movement sensor and the 4 cliff sensors along the bottom of the front. Make sure the front caster wheel turns freely. You may have to remove the rolle ... iRobot Roomba 560 Robotic Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Lately, my Kirby Ultimate G has been acting funny. When I push it forward, it's fine, but when I pull it backward on the carpet, the light on the front flickers and the power flutters off an on. I thought it might be the rollers, so tonight I turned the machine over and pulled out the hair that was wrapped around the roller. However, that did not fix the problem. I should probably backtrack a little bit. In the past, I have had problems with the vacuum running over its own power cord.

The cord will need to be replaced with a cord made for the machine, as it has a non-standard plug. The cord cover is held in place with a # 20 Torx screw. Remove the screw and push the cover gently from behind to unlatch it. The handle must also be r ... Kirby Ultimate G Bagged Upright Vacuum

Is the roller brush supposed to turn when the power is on?? the sucktion is on but the brush doesnt roll

That means that you need to replace the belt which turns the roller brush. Here is the belt you need to replace and the manual which has instructions: ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Apparently something is binding the brush, keeping it from turning. Remove any string, hair, etc., that is wrapped around the brush. Removing the brush is the easiest way to do this, then cut the material through at one point.\015\012While th ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.

... Hoover Tempo Widepath Upright Vacuum - Blue

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!

First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums

Bought a Kenmore Progressive canister vacuum at a garage sale that looked in better than average condition, filters clean, new bag, all accessories intact, some debris in roller brush. problem is no suction when turned on. There does not appear to be any obstruction in hose. did not have manual

Hello,Carnister vacuum cleaners are all built with the same principle in mind. A motor \015\012generates power which powers a vacuum which, in turn, creates suction to\015\012 lift debris. The most common areas of suction loss are within ... Kenmore 25512/ 25513 Progressive Canister Vacuum

My roomba will not go forward. it will turn in a circle for a few seconds then shut off with the red light flashing. i cleaned the brushes and the wheels. i dont know whats wrong with it.

... iRobot Roomba 530 Robotic Vacuum

The belt burnt out and it seems as though the red arrown does not release the belt. Like it is backwards from the green arrow. It had a burning smell and the belt broke. Then the second belt started to burn out when the brush roller wasn't spinning. Not sure what might be wrong. Green light will not come on either.

It sounds as if there may be a piece of the broken belt in there. Look carefully with a flash light and remove any remnants you find, using a pair of pliers if you have to.\015\012\015\012Also, remove the entire brush roller assembly and ... Kirby Ultimate G Bagged Upright Vacuum

Suction? Hi there, when I turn the vacuum on and place my hand under the roller brush, there is very little suction. Could something be wrong?

You won't feel a great deal of suction like you tried to do it. But look at the fan, if it isn't worn down, and the bag fills with air when you turn it on, then the suction should be ok. If you haven't changed your belt in awhile, I am sure that it ... Kirby Ultimate G Bagged Upright Vacuum

I have a new Kenmore magic bued and I am about to change bags for the first time. Trying to do this the clip that is supposed to hod the bag close to the whole keeps coming off when I replace it and close the lid, turn on the vac the sucction is very low and it keeps showing the bag is full which is not true / what is going wrong here ? Thanks so much for supporting, Beba

Sorry to hear that you are having problems with you Kenmore Magic Blue.There is a so-called "bag full indicator", which will only turn red if it got some major blockage. This is the reason why there is no power suction.The "fu ... Kenmore Magic Blue 24195 Bagged Canister Vacuum

I have the Bissell Pro-heat 2X which is new and only used one time and today I am trying to use it and the brushes will not work at all. They will not turn and spin like they are suppose to.....Please Help ! John Baumgartner Roanoke, VA

Look on the front of the little gree guy and where the switches are you should see a small diagram of a brush above or below one of the switches flip the switch to the brush diagram ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0864 seconds