Having problems with your Dirt Devil Featherlite Bagless Vacuum M085845Vacuum ?

Upright dirtdevil roller jammed - how to remove square endcaps for cleaning

\015 Brush roller does not turn, took out and the roller is jammed, need to remove end caps to clean up the bearings inside but cannot open the square end caps,\015

Answers :

The brush roller is secured with elastic stop nuts. Clamp the nut at one end with a wrench or pliers and remove the nut from the opposite end. This will allow the shaft to be removed completely for cleaning
Repair Help & Product Troubleshooting for Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Upright dirtdevil roller jammed - how to remove square endcaps for cleaning


The brush roller is secured with elastic stop nuts. Clamp the nut at one end with a wrench or pliers and remove the nut from the opposite end. This will allow the shaft to be removed completely for cleaning ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg


Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums

Vacuum works fine when using the attachments, but as soon as we try to use it in it's normal upright position it does not work. We have cleaned all filters and removed debris from roller, but nothing has helped.


Greetings,\015\012\015\012There could be a few things that would cause your Dyson to do this. I will give you detailed step by step instructions along with pictures on how you can diagnose this problem. \015\012\015\012Po ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher


If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.


Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

RE: DYSON DC07. Cleaning the roller I removed one end and cleaned it. Cannot get the roller back on the vaccum. If you could give me instructions on how to do this I would be very appreciated. Thank You


Try this link. http://www.sparesaver.com/help-and-suppor ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Hi, I have not owned my electrolux pronto 2 in 1 for very long but the roller brush has stopped turning. The handheld part works and the green light is on. I have done a thorough cleaning of the roller brush and all other removable parts. What might be causing the roller brush to not work? Thanks, Jen


Check the end cap bearings ... and replace the belt even though it may not be broken. Put a drop of sewing machine oil (no more) in each end cap bearing. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

Upright cleaner BUC11700GB. Roller will not rotate, belt intact roller free. Have removed cover and roller motor not working when switched on.


... Bosch Vacuums

How to refit the front brush belt driven roller ? We removed the roller accidentaly when cleaning out hair that had got wrapped around the roller. How can we put it back in?


Hi well if you go onto youtube and look for replace dyson clutch it will show you how to refit your brush good luck ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Royal upright metal vacuum. The roller stopped spinning. I took the roller off and the ends were full of dust and hair. I would like to take the ends of the roller off to clean more -- how do I do this?


... Royal 4000 Classic Bagged Upright Vacuum

How do I remove the brush roller onthe eureka clean living vacuum model no 3281 AZ


... Eureka Vacuums

I have a model # 880 Royal upright that the brush roller ends are bad. Can I get replacements for these? They have the 1/2 in. square ends. What about replacement for the whole roller assembly. The brushes are fairly well worn. Thanks, Arthur Summers


The below site sells the rollers for some models. I'm not sure about yours. The second one, part number R-673273, may fit. Check your brush for a part number. \015\012\015\012 ... Royal Vacuums

Roller brush on Dyson D25 not working. Have removed roller brush and cleaned it as per instruction booklet advise. But to no avail.


... Dyson DC25 All Floors Bagless Upright Vacuum

It seems to be blowing dirt around not suking but when removing the attachment to clean stairs etc the pipe works fine have washed filteR ? SLIM UPRIGHT DC ALLERGY 18. Have cleaned out filter emptied cylinder taken any bits of cotton or hairs from brushes..........


... Dyson DC07 Bagless Upright Cyclonic Vacuum

I took off the brush roller to clean it and now I can't get the roller to work unless the machine is standing upright. The side that's not connected to the belt keeps falling out.


The solution for your situation is as follows: You need to put the retraining clips on over the arms to properly put them in place You most likely put the retaining clips on too early. ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

Kenmore InteliClean 116.35923502 Two, I believe unrelated, problems. 1) The InteliClean sensor lights stay amber and red even when the machine is in the upright position and the suction line is disconnected from the cleaner head. 2) There is a lot of vibration and noise in the agitator roller housing. I picked a little hair out of the roller brushes but other than that they were clean. Thank you for any suggestion you might offer.


I had the same problem with the amber inteliclean light continually on. I found the problem to be in the plastic housing that connects the suction hose to the back of the upright section. You have to remove three screws and gently pull ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I REMOVED THE PLATE THAT IS OVER THE ROLLER TO CLEAN THE ROLLER OF HAIR AND NOW I CAN'T GET THE PLATE BACK ON AND TO SNAP INTO PLACE


If you go to this URL:\015\012\015\012http://media.dyson.com/downloads/us/floorcare/manuals/dc17_opmanual_usa.pdf\015\012\015\012you can see a diagram on how they suggest to take the plate off and clean the unit.\015\012I hope this will o ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson DC25 got stuck and wouldn't return to the upright position, I figured out that one side had jumped the track and gotten stuck in the square hole below the track. I did not want to break the plastic to force it back, so I removed the screw on the right side that was holding the kick stand on and removed the kick stand, also a spring thing came out. Problem is, now I have no idea how to re-install the kickstand. Can't find a technical manual or video anywhere, it can't be very difficul


... Dyson DC25 All Floors Bagless Upright Vacuum

Hoover tempo upright is clogged. I can only vac for a few minutes, then I have to unplug it and turn it over and clean out the under part under the roller. It is totally stuffed with dirt and dust and carpet fibers. I have a new bag in. It is like it is clogged up inbetween the bag and the roller. Also gets clogged when using the hose. It is maybe a year old. How can I take it apart and unclog it?


Disconnect the hose and head and wands. Drop a quarter thru the hose, the handle sometimes clogs. peer thru the wands and inspect the elbow on the head for blockage as well ... Vacuums

I have a brother project runway limited edition sewing machine and there is a constant jam with the bobbin threading and I have cleaned it,removed the sewing plate and everything I can possibly think of. If the bobbin case is scratched would it cause the jam?


Hi The usual cause is that there is a problem with the upper \015\012threads, often it is not caught in the tension discs. When you thread \015\012the machine, make sure that the presser foot is raised - this causes the\015\012 te ... Vacuums

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

I unscrewed the roller brush protective cover and removed the brush to clean it. Now the roller won't turn because the drive shaft is not turning. Is there a reset button or something?


I looked at the pictorial of this vacuum at this URL:\015\012http://middleeasten.bissell.com/images/UserGuides/3750.pdf\015\012\015\012This shows the belt to slide on the motor drive pulley and also on the brush. If the brush is bound up on th ... Bissell 3750 Lift Off Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0822 seconds