Having problems with your Dirt Devil Featherlite Bagless Vacuum M085845Vacuum ?

When i push on the power button on it runs only as long as my foot stays on the on/off power switch once i move my foot it immediately shuts off?

\015 I emptied all the containers and unpludded it from the power outlet and let is sit overnite and it still continues to have the same problem.\015

Answers :

Repair Help & Product Troubleshooting for Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When i push on the power button on it runs only as long as my foot stays on the on/off power switch once i move my foot it immediately shuts off?

... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity

... Vacuums

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

Bag light stays on, powers on then shuts off immediately. What is the problem?

First check to make sure there is a bag in the machine, if so make sure that its in securely, there is a pin switch in the bag door that wont allow the machine to turn on if there is no bag in it. If that's okay, then find the knob on the top of the ... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have an Electrolux Silverado deluxe canister vacuum that won't run. It was running fine, I turned it off to move the plug and then it won't turn back on. It is getting power to the switch. Any help?

... Electrolux Vacuums

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you

Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

I have the same problem as steve967 The dyson dc16 is fully charged, runs well for 5-10 seconds and shuts down. I wait for a second or 2 and it runs again for 5-10 seconds. This will continue for numerous cycles, until I am finished cleaning. I have cleaned all the filters, and the power is good, The system will just not stay on. It is just over 2 years old. A friend of mine had the same problem with his Dyson DC16 after just a couple of months and has replaced his Dyson with a Black N De

Dear Michael_Stad,I am going to sound like a broken record but here is my same answer to another person with the same problem.I have I had the same problem with my Dyson DC16, where it only runs for a few\015\012seconds at a t ... Dyson DC16 Root 6 Bagless Handheld Cyclonic Vacuum

Hoover U8185-900 motor shuts off when you move the cleaner forwards but it runs when the cleaner is moved backwards

... Hoover U8185-900 Upright Vacuum

Stops Immediately. We have a Beam Serenity model 2100 installed in the home and when the hose is inserted into the wall it turns on for a few seconds and then shuts off on it's own. Turning the handle's power switch off/on restarts the unit only to have it once again stop after a few more seconds. The canaster is clean. What could be causing this stopping issue? Thanks.

The Relay Control Board in the 2100 is bad. Replace and it should work just fine. ... Beam Industries 2900 Serenity Plus Central System Vacuum

I was using my Heritage 11 vacumn with the hose attachment and the motor shut down like the power went off .When you push the switch on the housing the light comes on but the motor does not run.

Hi, the motor could be overheating. Most vacuums have a heat sensor that shuts the vac. off if there is a clog. Let it sit, feel if it's hot. If so you may have a blockage of dirt etc. Try to clear it, let it cool and tart it up. I hope this helps, i ... Kirby Heritage II Vacuum

The Roomba 535 runs but stays in 1 spot moves 2 inches turns and repeats the process about 10 times. then a red indicator light starts blinking and the unit shuts down

Any beeps? If so, how many?\015\012\015\012Is there a pattern to the light blinking?\015\012\015\012Not really enough info yet to be certain, but it sound like the cliff sensors may be dirty. \015\012\015\012Here ... iRobot 530 Roomba Vacuuming Robot, White Vacuum

On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.

... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

I had the vacuum cleaner question about the canister and the wand/powerhead... the Kenmore Progressive Vacuum canister model 116.25812 and the canister not powering off without unplugging the vacuum. The solution I received that they both run on their own switch so it is normal makes sense. However, is there a power switch on the canister anywhere? The only way for the canister to be turned off is by unplugging it. Any ideas? One would think there would be a switch. I am new to fixya and hope

Hi. On some models, one switch controls all of the power. Your issue, which is no working switch is almost certainly a blown triac on the circuit boar ... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?

Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I just got a Shark Bagless Upright Pet Pro V1310PT-FS and the power switch will not stay on. If you hold it down, it will turn on and the vacuum will pick up but the switch doesn't seem to stay in the "On position". Any ideas how to quick fix this?

... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa

... Electrolux Vacuums

While vacuuming the beater bar shuts off all by itself, the main power source stays on. I touch the power button on the beater bar to start it again and it shortly after shuts off again. why is this happening?

... Dyson Stowaway DC23 Bagless Canister Cyclonic Vacuum

Power head motor is good,runs great from test cord switch seems to work. brush roll cleaned but power head motor will not run

If you have checked the power delivery down to the powerhead and you have current running to the powerhead, then you likely have a burned fuse. There is a fuse built into the powerhead motor and is usually located on the field winding. This is not ea ... Eureka 6831A Bagged Canister Vacuum

Power switch won't stay on. If I hold it down the power stays on. As soon as I let up, it stops.

Most likely the ratchet mechanism on the switch is faulty.Switches are available if you search on eBay for a few pounds, and if you've reasonable DIY skills and tools, it's fairly easy to do.Have a look at ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Savvy Brush only runs when the vacuum is moved backwards

Replacing the entire upper handle assembly with OEM Part #48663238 will solve your issues, for a cost of about $35 plus shipping. ... Hoover U8185-900 Upright Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

When connecting the wand into the brush component. sporatic power (sometimes runs sometime nothing) the power is on again off again. when hold pressure down on the wand the power stays on. do you think the coupling connection is bad on the wand? would the wand replacement likely be the culprit?

There is is switch or sensor in the connection. Likely that piece is worn or shorted out. You may be better off getting a new wand piece ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

We have a dyson 07 and I am guessing the switch needs replacing as it won't stay running unless you hold the switch down. How do you change the switch?

Hi its Darran at Dyson.We can arrange for an engineer to repair your machine for you. If you would like to arrange this, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US).Kind regardsDarranDyso ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have an easy flo vacuum model # 199C and it won't shut off. It started out as an intermitent problem but now will not shut off when the hose is unplugged, nor when the off/on switch on the main unit is shut off. the only way to get the motor to stop running is to unplug the unit. Any ideas?

Just had this same problem. I unplugged the low voltage signal wires and the vacuum stayed on. Thus eliminating the possibility of the signal wires shorting out somewhere. I'm not really sure which wire(s) were causing the problem. But when I disasse ... Easy Flo EF1500 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0662 seconds