Having problems with your Dirt Devil M086700 Vision Bagless Upright Vacuum ?

Our dirt devil bagless upright (110002) stopped working while vacuuming. we cleaned everything out and cannot get it to start again. the motor is warm, but does not smell hot. is there a reset switch/button we need to push? thanks, Carol

Answers :

Hi, no im afraid its not that easy, the problem is with the wire that goes into the vac from the mains, now you see where the mains lead goes through in the back of the vac well what happens is when you vacing and moving the vac around this part wears and causes a short or loss of connection, now it usually happens when your using it then the free cable runs out and it pulls on the vac when you try goign further than the wire reaches, so the problem you are having is with the connection between the wire and the on/off switch, this is a very common fault with all vacs of this type.

to fix it your going to need to remove the cylinder and see if their is an access panel on the front of the vac behind the cylinder you take off to empty.

how ever if you have no electrical skills then its not safe for me to tell you how to do this repair, if you get it wrong you could do harm to anyone who uses the vac ok so be warned i have told you this ok.

the work involves removing the panel the other side of the switch then you need to undo the wires going to the switch you then need to pull the mains wire out of the vac so its no longer connected then cut it back 3 or 4 inches so as the part that is faulty has gone then you need to fit it all back together the right way round and make sure their is no bare wire showing and that it is all secure and then it should work.

but before you do all that check the fuse in the plug first as if its got hot this fuse may have blown so i would check that first before you decide what to do next ok.

it wont cost much to pay someone to do this as it wont require any parts, if you could take it to a reapir shop yourself then that will be even cheaper as you wont be paying a call out fee, also check if you have any warranty left on it as this fault wil be covered

let me know how you get on or if you need further assistance ok

please can you rate this solution as i have a whole page of unrated posts, thanks
Repair Help & Product Troubleshooting for Dirt Devil M086700 Vision Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Our dirt devil bagless upright (110002) stopped working while vacuuming. we cleaned everything out and cannot get it to start again. the motor is warm, but does not smell hot. is there a reset switch/button we need to push? thanks, Carol

Hi, no im afraid its not that easy, the problem is with the wire that goes into the vac from the mains, now you see where the mains lead goes through in the back of the vac well what happens is when you vacing and moving the vac around this part wear ... Dirt Devil M086700 Vision Bagless Upright Vacuum

Sewing machine Guru needed ;) Elna Grasshopper (new to me) circa 1950 The light works, but there was no hummm when knee pedal engaged. I have the motor out, and it is very stiff to turn. I'm at a total loss when it comes to motors and electricity. It doesn't smell burned, doesn't smell at all beyond normal machine smells. (Yes, I made detailed notes and diagrams as I took said motor out!) One other note. The long thing which my husband said might be a capacitor -- it looks like

I just purchased a fairly tidy Elna 'Grasshopper' sewing machine (1951) with the same leaking capacitor problem. I carefully removed the capacitor for examination. It is actually three capacitors in one - no chance of a direct modern replacement, but ... Vacuums

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.

Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

When I turn on my Eureka Smartvac 4870 is the light blinks sporadically and smells like the motor is burning. How can I tell if the motor needs to be replaced?

Hello. If the motor is running smoothly and the only symptom of a problem is that the light blinks sporadically I would inspect the wiring to the light. It may have a loose connection, or a burned insulation which is causing the burning smell. Onc ... Eureka Smartvac 4870 Bagged Upright Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please

... Vacuums

My Bissell 1697w motor is sparking and smells like something is burning. Do I need a new motor?

You may want to contact a BISSELL Authorized Service Center to have a qualified technician inspect your machine.\015\012Here's a quick link to locating one. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

<2 year old Eureka 4870DT with strange noise and aweful smell from motor. Roller also not rotating. The belt is intact and all tubes are clear. Do I need to replace the motor?

The price of vacuums these days are falling all the time - esp on EBay. This sounds like there's a foreign object or simply dust which has managed to get into the motor thus causing the burning smell or that the roller brush fly wheel is loose and ca ... Vacuums

Burning smell from motor...what needs replaced?

Without the complete model number, I don't know for sure what componets you have, most likely is the motor. You will have to take the motor cover off and check it out. You can go to sears.com, click on parts, enter your complete model number, scrol ... Kenmore 25812 / 25813 Progressive Bagged Canister Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

Vacum I need to check the brushes in the motor smells have removed four screws but the cover is not coming off. I dont want to damage this by forcing it but cannot find any other screws Thanks fairweather

Hi there!\015\012\015\012It would certainly help if you said which model it was.\015\012\015\012I can only give generic help now, and do the best I can for you.\015\012\015\012Most plastic products rely heavily on ... Vacuums

Hello, I have the BISSELL PRO STEAMER MODEL 8805-1, it's mking rattling sound near the motor, & smells like melting rubber like when the belt is burning. I need check the belt, it's OK. Thanks so much, Susan

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

My Sebo Felix ET1 has a burning smell, have checked there are no blockages, could it be the motor brushes need replacing, if so how do I do this? Thanks, R.Stevens

... Sebo ET-1 Bagged Upright Vacuum

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech

... Vacuums

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Brand new 3HP shop vac smells like motor burning when turned on!

... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

Problem with E series rainbow, motor starts then slows down to a halt and smells.

From what you describe, you will probably have to replace the motor. But you could take it apart and see if it just needs carbon brushes. ... Vacuums

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.

It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

BURNING SMELL My DC 07 has suffered from poor suction in the upright position for some time now but this morning it ground to a halt. It was if the motor had burned out. I turned it upside down and some small stones etc tumbled out. I tried switching on again and the motor kicked in but the smell was horrendous so i switched off immediately. If it's likely to be **** inside the motor area i don't no how to access it. I've removed for fixing screws but still unable to prise apart. Is it just the

Hi.\015\012\015\012Try this site http://dysonmanuals.llc.nu/ has service manuals covering removing the Dc07 motor. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.

You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums

Miele Vacuum Cleaner - burning smell / motor won't stay on

Check brush the belt may have popped off and is binding or brush is binding clean brush of any debris thread/hair wrapped binding brush and check and or replace belt ... Miele S318 Bagged Canister Vacuum

Motor makes loud racket and smells like burning, but still works.

Bag? There is a paper filter and maybe a foam filter ... bag? Maybe this is a newer model that I am not familiar with. Anyway ... ...\015\012\015\012It sounds like your motor has been eating dust. Please check here for your repair: ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

Need to open motor compartment

Use a flat blade screwdriver, The dusy compartemnt door will come off by pushing it back, it just pops out. Then the rear top cover is held on by a tab, one in each corner. Put the flat blat in the slot at the bottom of the cover and work it until ... Panasonic MC-V9620 Canister Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

Need replacement bushing part number for Kenmore, or motor?

... Kenmore Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1342 seconds