Having problems with your Dirt Devil UD70095 Bagless Upright Cyclonic Vacuum ?

Roller brush pin spins off center

\015 The pin in my brush roll spins off center causing the brushroll to make a grinding noise.\015

Answers :

If you are describing the problem accurately, you need a new brush and new bearings (bushings). Once they get worn to egg shape, no matter how slight, the problem will only get worse.
Repair Help & Product Troubleshooting for Dirt Devil UD70095 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Roller brush pin spins off center

If you are describing the problem accurately, you need a new brush and new bearings (bushings). Once they get worn to egg shape, no matter how slight, the problem will only get worse. ... Dirt Devil UD70095 Bagless Upright Cyclonic Vacuum

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

My floor brush stopped spinning, I cleaned everything out as per your directions in other posts and following the instructions in the manual. Now the floor brush wobbles and has a hard time spinning when upright. Looking at the end of the brush, opposite the drive belt, the bearing-type end that the brush spins on appears to be off-centered. Is there an easy way to fix this???

... Bissell 3130 Bagless Upright Vacuum

A cap on one end of the roller brush is centered and turns freely. The one on the other end is not centered and does not turn but does not look broken. It looks like it's supposed to be that way but it doesn't allow the roller brush to turn. How to I solve this?

It's hard to say definitively what the problem is here. Rollers usually have bearings at each end and they can wear or freeze up especially if they are exposed to water. When you say that the cap is not centered, I assume that you mean that you hav ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?

The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Kenmore Canister Vac, Progressive, 25512 255513 model. Brush won't turn. One end of the brush roller, end closest to belt, is off center which is keeping it from turning freely. The end cap is like a square. Other ends turns fine. Do these end caps come off? If so how? Can't get it to budge. This is exactly what is keep brush roller from turning.

Take a flat head screw driver and pry the end cap off. It will come off. You might have some string or hair around it causing it to not turn. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Should the roller brush on the kirby always be spinning?? just inherited a kirby 5, and the roller brush is not turning when the vacume is on. ??

Yes it should alway be spinning when you switch on the machine, if it's not spinning i would sujest the belt as come off or broke this video will show and explane what you need to do to replace or put back on . ... Vacuums

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

I have an Oreck XL Platnium. It smells like burning rubber and the brush roller binds and stops as you pull it back and forth, even on a hard floor. I have changed the belt 2 times. I have taken the brush roller out and checked it. It seems to be spinning freely. What could be wrong??

... Oreck XL Ultra Bagged Upright Vacuum

The roller that spins with little brushes stopped suddenly and no longer spins. I pressed the red little knob at the end of the roller but it doesn't fix the problem.

Open up the roller area check to see if somthing got picked up and jammed into the rollers so that it can't work, a rock or a screw or you might even have a large amount of string or fibers wrapped around the shaft or brush keeping it from rolling ... Dyson Ball DC24 Bagless Upright Vacuum

Kirby sentria My roller brush won't spin belt is not broken I cleaned the Roller brush and put it back it. It put it back but it looks like the sensor balls aren't touching the plastic part underneath. The green light Doesn't turn on either. It was just working and it stop picking up out of nowhere this

... Vacuums

Roller brush stops spinning and vacuum makes noise. Brush will spin normally ok, until you use it on the rug.

That means that the belt is stretched and can't turn the brush against the resistance of the carpet. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a Panasonic Performance plus MC-V5217. Something got stuck in the rollers and it stopped spinning. We've cleared the brushes but can't get it to spin. Is there a reset button?

... Vacuums

Brush roller on windtunnel won't spin

It sounds like you need to replace the actuator arm or the cable to it. Look for Hoover part 43143046 for a start. I've got a similar problem. ... Vacuums

Shark vacuum roller brush attachment doesn't spin

... Shark Navigator Bagless Upright Vacuum

Hoover steamvac model f-5883-900. The brushes spin freely when i spin them myself,but dont spin when running. The vac runs but sounds differet like a higher hum. To fix this would the pin be broken or the turbine

... Vacuums

I have a Hoover steamvac Dual V carpet cleaner Model No. F7427-900. This is a spin scrub upright. My brushes will not work. We think the white square that the brushes fit up into in the center of the brushs is not turning. Can you help me.

You are on the right track! Place a screwdriver (flatbladed) into the white drive square and try to turn it. If it is locked up the drive assembly is your problem. It is very common for these parts to lock up because of the moisture involved with ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover steamvac model f-5883-900. The brushes spin freely when i spin them myself,but dont spin when running. The vac runs but sounds differet like a higher hum. To fix this would the pin be broken or the turbine

... Vacuums

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.

Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum

Its like the roller brush won't lower and it doesn't "engage" anymore. I posted this but input the wrong vacuum model ....not sure if that matters? I can vacuum and you still see footprints on the carpet. I have suction, just no brush action, yet the brush spins....

Sorry about that, I guess I have to post this as a solution in order for the pictures to display. Here's the entire solution on a similar problem that I've answered previously. Please let me know if you need help further diagnosing the machine, I ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Roller brush won't spin (bissel 6390/3910 series)

I just fixed mine. It took me all of 10 minutes. Pull the brush out. Stand the brush on end on the edge of your study work bench/table top. while holding the brush vertical( on end) take a small phillips screwdriver and tap using a hammer on the meta ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Roller brush isn't spinning

Depending on which powerhead this is, if you removed the light cover, then removed the 2 screws, from the bottom edge, you will see a slot where you can insert a flat blade and pry out to release the tab, there is one on each side. If this one where ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

The motor is running, the roller brush spinning rubber smell

The belt may be stretched replace it ... Vacuums

Roller brush not spinning?

  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0660 seconds