Having problems with your Dirt Devil Vacuums ?

I can't get the front cover over the bag back on

Answers :

Do you have the correct paper bag for this machine. Sometimes if the wrong one is used it will not allow the cover to go back on. Or you might need to fold in the sides of the paper bag so that the door will close fully.
Repair Help & Product Troubleshooting for Dirt Devil Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I can't get the front cover over the bag back on

Do you have the correct paper bag for this machine. Sometimes if the wrong one is used it will not allow the cover to go back on. Or you might need to fold in the sides of the paper bag so that the door will close fully. ... Dirt Devil Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?

Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

We have Nilfisk Tempest 1500W bagged cleaner. It just stopped working and I have taken off top cover and all wires/contacts look OK. But power still not getting through I assume. The retractable lead goes into base and cant get to this area. How do I check main lead or perhaps you provide details of serviceman. On North Shore, Auckland, NZ.

... Vacuums

Cant get cover back on Bissel Pro Heat

... Bissell 8910 ProHeat Clear View Upright Vacuum

I have an older Kenmore vacuum cleaner - Model #3285590C, Serial #DG4117817. I can't seem to figure out how to get the motor cover off. 2 bolts in the front have been removed but the back has no visible bindings. It seems to be held from inside the compartment! Whats the catch here!

... Kenmore Vacuums

My Windsor Sensor XP12 says the bag is full when it's not. I have removed the hose, brush, and filter and cleaned everything. I can put a bag on without the cover and it works great. However, when I add the bag to the front cover and close the latch the right way, it does not work. I'm thinking that the cover is not seating the bag correctly over the hole, but I can't figure out how to fix it. Any suggestions?

... Windsor SR12 Sensor Bagged Upright Vacuum

When removing the canister bag, the plate and spring that it slides into popped out. When I put them back in, the bag full indicator is completely red. It is a new bag and filters. I think I am not getting the plate and spring back in the canister correctly. Any instructions or pictures showing proper insertion and configuration of these? I looked in the manual and the part is only shown while bag being inserted.

... Miele S514 Solaris Bagged Canister Vacuum

My Oreck is 10+ years old. The bag will not remain on the opening of the handle inside the bag. Dust goes into the cover rather than in the bag getting in the zipper which makes it very difficult to unzip the cover. Any suggestions?

Check and make sure bag collar is behind the two lips. if it isn't it will leak dust and make it hard to open. ... Oreck XL Ultra Bagged Upright Vacuum

I have a Hoover U5111-900 that, every time I attempt to use it, shoots everything it should be sucking up, back out toward my feet. I have replaced the bag, pulled out lots of animal hair and such from the area behind the bag, and taken off all parts able to be removed without a screwdriver and pulled out all chunks of hair, dirt, etc. It still keeps shooting everything it should **** up out the back. Is there something I can remove to get the clog out if that's the problem? I'm scared I wil

Hello,\015\012\015\012Although I could not locate info on a U5111900, the link below shows a similiar upright and things to check for clogs. See page 12 and refer to the pages noted.\015\012\015\012 ... Vacuums

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!

... Miele S7210 Bagged Upright Vacuum

Bosch canister vac BSG81313. Took cover off to remove lots of hair, dirt etc from running without bag in place. Everything went back together OK, but cord reel spring went zip when cover was removed. How do I rewind the spring so there is tension when the cord is pulled out ? Wound cord back onto reel, but reel just clicks ever revolution etc...no tension when cord is pulled out of vac. Bob

The spring inside the hub of the cord wheel has escaped from the locking tab. You must completely dismantle the vacuum to access the cord wheel - take it out, reattach the spring and reassemble the unit. All you need is a phillips screwdriver, a pai ... Vacuums

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard

Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums


Http://newzealand.bissell.com/images/IncludeContent/Service_Center_Help/Upright_Deep_Cleaner_Repai ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I have a window fan with two fans in it & I cannot get the cover or back off so I can clean it. I* have taken all the screws out that I can get to , but there are two clamps that I can't get off, I'm not sure why the clamps are there but they are on the side with the accordian extention. Please tell me how to get it apart - after 2 years it is really filthy!! Thank you, Janet

Remove all the screws, pry clips off that hold on the extensions, than fan will pull apart. The clips must be pried off. They will not break. Then remove screws holding in the fans and remove them as well. Fairly simple process. ... Vacuums

Wont re-assemble I took the bottom plate off to clean out the rotary bush and can not get the plate back on! I think it is the position of the roller but no matter which way I place it when i turn it , it flicks back into the place that means i cant put the plate back on!

Assuming you did not remove the brush roller to clean it and consequently did not reseat it, I am guessing that the bottom plate is not reinstalling as it should. On some uprights, the bottom plate hooks in at the front and is latched in place with c ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have the electrolux guardian-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)

Hi,\015\012Check your hose you have something stuck in the hose...stretch it out straight and run something through it to push out whatever is stuck in there...\015\012\015\012heatman101 ... Electrolux Guardian Bagged Canister Vacuum

I have the Aerus Lux7000-My full bag light indicater is coming on even with a new bag. It gets worst-the machine will cut off when I insert the hose or put my hand over the hole where the hose goes. I changed the filter on the back and put in a new bag. Help please :)

Hi, you very likely have a defective control valve under the dial on top of\015\012the vac , or a kink or blockage in the tiny pressure hose that feeds\015\012the air from the throat of the vac or the back of the bag chamber\015\012against the two si ... Electrolux Guardian Bagged Canister Vacuum

Hi, I have a Dirt Devil Model # M08100REDC. I desperately need to change the bag, but I don't see an obvious way to do it. I'm afraid to try pulling on the cloth tab thingy that's just below the handle, between the rubber ring that holds the bag on the vac, because it seems like stuff will fly everywhere from the force required to remove it, and I might not be able to get it back on there. Should I just pull on that cloth tab until the bag comes off? Thanks, Roberta

You can pull on the tab to remove the bag, but probably a better way is to gently pull on the rubber ring that attaches the bag to the back of the vacuum body. If you don't yank and ****, it should come off without spilling the dirt. There may also b ... Dirt Devil Classic M08100 Bagged Handheld Vacuum

I cant get the belt and roller back on

... Riccar 8955 Upright Vacuum

Getting a Eureka central vac cloth bag back in after cleaning

I found that if you start by making sure that the tab that you pull to remove the filter is in a spot where you can reach it next time you need to remove it. Next, put the filter in over the inlet spoutand push it up to the white "stops" then gently ... Vacuums

Can't get the covers off Electrolux Model C102G, acts as if bag is full, but bag is new and empty!

... Electrolux Vacuums

I cant get the roller back in place

On the ends of the roller turn the ends and you will see some teeth ,the teeth are supposed to be aiming down.if its because of the belt,slip the belt over the roller then put the belt on the motor shaft first and pull the roller towards the front a ... Oreck XLS700A Upright Vacuum

I went to change the bag on my eureka powermite 930a and the whole thing came off. I don't know how to get the part that holds the bag back on. Help!!

... Vacuums

What hose gets hooked up for upholstery cleaner. The one that usually goes in front? I cant get my vacumn to turn on.

Hi!You need to take the power nozzle off and attach the thing that looks like a little plastic "cup" with two hooks and a screen on it. This is the intake guard. Attach it to the front. Now remove the cloth bag and put the hose on the hole wher ... Kirby Ultimate G Bagged Upright Vacuum

I can't turn the belt off of my Kirby vacuum. I had the front off of it earlier to attach the hose, but now when I put the front back on, I can't get the belt to turn off. The lever twists about 3/4 of the way around, but will not go the rest of the way.

Turn the front part to the green so it is level and then twist the front to the red make sure the belt catch the hook as you twist it then if the belt is hooked just put it back on the vac like normal and lock it in place then twist it back to the gr ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0937 seconds