Having problems with your Dirt Devil Vacuums ?

Dirt Devil 086905 has suction through hose, but will not **** at the power floor head. Cannot find a clog, brush spins. What should I be checking?


Answers :

Need to take the head apatr as if you were replacing a belt. Look for the clog... it's there
Repair Help & Product Troubleshooting for Dirt Devil Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dirt Devil 086905 has suction through hose, but will not **** at the power floor head. Cannot find a clog, brush spins. What should I be checking?


Need to take the head apatr as if you were replacing a belt. Look for the clog... it's there ... Dirt Devil Vacuums

No power when turned on, I checked motor brushes and they are almost worn out, could this be the problem? and where do I find replacement brushes? I have checked on Dirtdevil's site but I don't see any motor brushes. I am in Montreal, Canada. Thank You.


Hi,\015\012Before that I wouild check the switch...the switches on those things go bad regularly...get a meter and check the power on either side of the main switch and I think your problem will be there...\015\012\015\012heatman101 ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

No power going to the rotating floor brush. Check...


How do I change the belt? ... Bissell LiftOff Revolution Pet Vac 37602 Vacuum

Hoover Windtunnel U5750-900 Agitator brush is weak. It turns fine if I tilt the vacuum back, but it slows to almost 1/4 speed when it touches carpet, even on the highest carpet setting. I've replaced the agitator belt twice. The brush used to turn powerfully even on the lowest (Hard Floor) setting. Ideas? I should probably lube the agitator brush ball bearings, and re-check the belt, but, other than that, I'm stumped.


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My DC17 is only a few months old, but I've already had to clean the filter. Since I reassembled everything, I'm finding chunks of carpet fiber and dog fur on top of the filter inside the filter container. Iam getting slightly less suction from the floor assembly as well. I've checked the hoses, brush, and brushed out the inside of the plastic container, but hasn't helped. Ideas??


Everyone needs to own an air compressor,\015\012if you own a bagless vacuum\015\012\015\012You blow it out every other time you use it.\015\012\015\012Without compressed air, all vacuums will just\015\012basically ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery


Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Vacuum My vacuum is loosing it's suction power. I've checked the belt and it's in perfect shape...I've bought a new filter cup...I've checked for clogs and there aren't any...I've cleaned the entire machine...and I still can't find the source of the problem.


You checked the belt, but I bet it has stretched and won't drive the brush roll under load like it should. Belts only last a few months the stretch and should be replaced. Iff you have suction at the hose, then it has to be down below, either belt/ ... Eureka Whirlwind 4480 Upright Vacuum

There is no suction from the head on the floor. The hose is sucking properly but not the floor brush. I have checked for blockages and can't find anything - any ideas?


I have exactly the same problem!\015\012i think it is something to do with the transfer hose that changes the suction from the hose to the brushes ( it is at the bottom left of the machine as you look at it from the front! ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

While vaccuming it just stopped. Tried another outlet and checked power cord. Did find tube clogged with a dirt clog but no motor strain heard. Cleaned it out, Still not running


On the back of most vac's , u will find a red butten,use that to reset the vac. but even if that works u can avoid this usely buy ajusying the vac to a higher set . that helps reduse strian that the belt gets.\015\012 thanks\015\012 ... Bissell 68001 Canister Vacuum

When in upright it does not run or when I pull out the wand. I have cleaned the filter and cleared a clog. I turned it on it's side to check brush bars are okay. If I position it for floor vacuum it will run, but again when I pull the wand out it won't turn on.


I have a Dyson Or should say my wife has a Dyson and we suffered a similar problem when it wouldn't run in the upright position but would if we lowered it to say clean under furniture. It turned out to be a fracture in the mains power lead. Upright i ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob


Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum

My dirt devil quick lite has lost it's suction power. I have checked all the hoses etc for clogs or debris.I bought it in Dec 2010. I think maybe it needs a new filter. Where can I find an F44 filter or do you have any other solutions?


... Dirt Devil Easy Lite Quick Vacuum

I cleaned out the hose and removed brush to clean and checked belt. Everything seems to work but will not pick up or suction on carpet. The hose is totally clear from clogs. I can see the floor from one end to the other. What am I missing that might be causing lack of suction?


Hi troupdavid,I see that your Vacuum is having issues with it suction, you mentioned that you took it a part to clean it, see steps below.\015\012\015\012Check if everything is inserted prope ... Hoover Tempo Widepath Upright Vacuum - Blue

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hoover Mach 6 stopped running and won't start up. Cleaned the brushes(roll freely) and checked for a clog but couldn't find any.


Ya okay how do you get to the motor. Then when you get to the motor are you soppose to guess what is wrong with it by just looking at it.. What kind of solution did you give this person? I'd say not a very good one. ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

Power cord can not find replacement power cord for power brush attachment on kenmore canister vacuum, model #2491290 power brush attachment model # 5491290. i can not even find those model #'s anywhere online, not even partsdirect.com. any help would be great. thanks, david


Call 1-800-948-1358 ask for Buck mon.-fri. 9am-5pm est sat.9am-1pm est ... Vacuums

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

No power to sensor SR 12. I also have cleaned rollers and filters and bags. I have reset the handle. When I hit the power the check brush and full bag lights flash once. That is the only power that is getting through.The unit was in storage for a bit and got wet but its been drying off for a couple months. Is there something I can check or replace. Its a great Vac.


... Windsor SR12 Sensor Bagged Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Miele, Flamenco II. 2 probs. 1. the head brush is not turning when I put it on the floor. If I pick it up to look inside...the brush is spinning fast..I put it down on the floor...the head does not spin at all. 2. The suction power has dropped significantly. The suction used to be so intense, the head would **** itself to my floor and hold on...now, hardly any suction at all.


Sounds like the belt is not on correctly on the beater brush or the belt is worned out now for the suction check filters or bags that need to be empty or clean ... Miele Vacuums

I just bought a Z1750 twin tech vacuum. I am wondering if I can buy a power brush attachment for this. It only comes with the floor and "carpet" brush but does not have the beater bar (power brush).


... Electrolux Centralux Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0950 seconds