Having problems with your Dirt Devil Vibe Deluxe MCE6680V Bagless Upright Vacuum ?

Water will not spray out of the bottom of the vacuum i have checked all the connections and they seem correct.


Answers :

Hi this is a very common problem, whats happened is the cleaning solution has turned to gel and is blocking the pipe and not allowing the solution to come out what you can try is drain any cleaner out of the container and fill it up with hot but not boiling water and put a couple tea spoons of salt in then leave this to rest for 10min then switch the vac on and try the trigger and see if the water comes out you may need to hold it down for few minutes.

if after doing that its still not coming out then tip the vac up onto its back and have a look at the jets where the cleaner should come out now get a long pin and give the jets a good poke out with the needle doing this should unblock it.

if it dont then its going to need the bottom taking off to get to the hose and so you can squeeze any blockage out but let me know how you get on you may find cleaning the jets gets ot working it does most of the time.

remember when you have finished using it empty the cleaner fluid container and fill it up with warm water then let this run through the cleaner for 3 or 4 min just hold you finger on the trigger and let it drain through the whole vac doing this will prevent it from clogging up in the future

plz rate this solution as i have a whole page of unrated posts, thanks
Repair Help & Product Troubleshooting for Dirt Devil Vibe Deluxe MCE6680V Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water will not spray out of the bottom of the vacuum i have checked all the connections and they seem correct.


Hi this is a very common problem, whats happened is the cleaning solution has turned to gel and is blocking the pipe and not allowing the solution to come out what you can try is drain any cleaner out of the container and fill it up with hot but not ... Dirt Devil Vibe Deluxe MCE6680V Bagless Upright Vacuum

Bissell 7700 series, pro heat all rounder. Won't spray water. Have checked the line from the unit to the spray nozzel and all seems clear. Water doesn't seem to be flowing from the tank to the end of the unit where the hose connects into. What could be the problem? Any assistance would be greatly appreciated. Thank You. Steve


HelloGrasp the cleaning solution tank, and remove it from the machine. Reinsert the tank into the machine, making sure it fits snugly in the machine. If the tank is even slightly dislodged, water cannot get into the machine. Visually insp ... Vacuums

The unit (9400-3) is not spraying water from the lower deck but will spray from the hand held wand. Checked water levels and water/soap dispenser valves which seem to be working fine. Spray nozzles are not blocked. Where do you look now.


Same problem i have got, spent one day on the bloody thing but of no use, the only solution is to spray water from bucket and use the cleaner to **** it up. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.


I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.


The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

My Miele capricorn has started making an odd noise. It seems like something is blocking the engine. I've turned if off and on, and reset it and it still have the odd, almost loud barking noise. The power nozzle also does not seem to be working. I've checked the connections. Right before this happened I was using the vacuum. I didn't notice anything out of the ordinary until this.


Greetings,\015\012\015\012This is a major problem. The Miele vacuums motor should never make a loud noise, period. The way the motor is designed, it's quiet and should be quiet for the life of the motor. There are two motors on your ... Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

Wont spray i have the machine connected correctly but it wont spray water?


Did you press the trigger? If so, does it make any noise or does it not respond at all? If it does make noise, but won't spray, it could be a clog. Go to the vac shop to have it removed if you don't know how to take it apart yourself (I wouldn't risk ... Rainbow E series Canister Wet/Dry Vacuum

My Rexel shredder isn't switching on when connected to the electricity. I've tried all the settings but the machine won't switch on. I've cleared the shredders, checked the bin is in correctly, tried different electric points.


... Vacuums

This is a new machine I got for Christmas. All of the dirt is staying in the area where the brushes are and then falls out when you turn off the machine. I have checked all connections and the hoses seem to be clear. All filters have been cleaned and there is not dirt trapped that I can see.


... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is


... Samsung Quiet Storm 9048R Bagged Canister Vacuum

I am using my Hoover Steamvac FH5001 for the first time. It worked great until I had to empty the dirty water tank and refill the solution tank. Now it will not spray solution. I have double checked to make sure both tanks are inserted correctly, but to no avail.


Check all o rings to see if they are seated correctl= on the hoses that were disconnected. If not you will not receive suction to spray ... Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

When I engage the beater roller it will work for a short time (15-20 seconds) and then squeel loudly as if something is not engaging properly. I checked the roller ends and cleaned them but it seems to roll freely by hand while connected to the belt and then at a time it becomes very hard to turn by hand.


Sounds to me that the motor is shot. There is a main bearing the belt shaft connects to and it sounds like the bearing is seazing and gets worse when it nheats up. Soon it wont turn anymore at all ,once it siezes completely. These are rarely worth f ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Power brush does not run, light does not work when plugged in...checked connections...seems ok


... Broan-NuTone CV350 Performance Bagged Central System Vacuum

With my K6 Industrial Singer sewing machine the top thread seems to be too tight. The bottom thread is looping too much on the top of the fabric. The timming is ok. I have checked and rechecked that I have threaded it correctly. It was working great the other day. Please help as we are live out on a property and too far out to get someone out to look at it. Thanks Tania Sorry no category for sewing machines on your list


Hello there, loosen your top thread tension,if it looping on top of the material the tension is way too tight, you will also find changing the thread size to smaller thread, the top tension will also reduce,depending on application a good size thread ... Singer Vacuums

I have a Hoover steamvac that will not spray or pick up water. Earlier it worked fine, but stopped.... I ensured it was assembled correctly and checked the filter in the lid to ensure there was no debris....what more can I do??


I re-checked all my steps, the lid looked like it was on securely, but wasn't. I re-attached the lid correctly and had no further problems. ... Vacuums

Need A manual for U5025-900 Hoover Sprint vacuum want to check if the filters are correct. Was given the vacuum, seems like there is very little suction for the hose. Any help would be appreciated


Wasn't able to locate a manual, but you may be able to get the info you need from this page:\015\012\015\012U5025900 Parts ... Hoover U5025-900 Bagless Upright Vacuum

Beater bar won't work. Have done all checks in manual. Bar is clean, belt seems to be connected properly and in good shape. Any ideas? John Rike [email protected]


Hi, I would have to say, that if the roller-brush Is clean and the belt is on and in good shape, that the problem will be in the vacs motor assembly itself. If the motor comes on, the beater bar will engage and pick up debris.If it is coming on and n ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Bissell Little Green won't spray the solution. The suction seems to be working fine and the lines are all connected as they should be. What's up and how can I fix it?


I also had the same problem as you. \015\012Try suctioning up a full tank of hot tap water into the collection tank to soften/release a possible kink in the tubing inside of the vacuum hose that carries solution out to the spray tip. I di ... Bissell 1425 Little Green ProHeat Handheld Steam Vacuum

The roller in the power head will not rotate-- replaced belt & that is not the problem--now what do i check? the right end will move, but the left end seems fixed-- is that correct?


Sounds like the bearings froze up. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated


1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug


... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0700 seconds