Having problems with your Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum ?

Handle relase stuck in upright position and I have the vacuum apart and I dont know what to do what am I looking for it is still stuck


Answers :

Dirtdevil vacuums are so cheap. it's jammed. just go to a vacuum shop and get it repaired
Repair Help & Product Troubleshooting for Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Handle relase stuck in upright position and I have the vacuum apart and I dont know what to do what am I looking for it is still stuck


Dirtdevil vacuums are so cheap. it's jammed. just go to a vacuum shop and get it repaired ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

No suction i have been using mine for like a year or so. today i went to use it and then no suction. the water comes out but it wont **** it up. I haven't had any problems till now. I cleaned the little red filter but still nothing. I dont wanna take it apart with out knowing what im looking for.


I had exactly the same problem with my five-year old my Bissell 7920, and it's probably a broken pump belt.  See page 19 of your instruction manual for how to replace.  The Bissel ProHeat belt accessory pack costs $3.99 and you get a pump b ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have no suction for vacumming the floor. the wand is totally still working and sucking it heart out. clear hosing doesnt looked cracked. dont know where else to look.


Hi, if the wand is doing its job very well, you have to have a blockage some where, either in the hose where it attaches to the bottom of the unit near the roller section. It may be hard to see, but this is what is causing the bottom from not picking ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

BURNING SMELL My DC 07 has suffered from poor suction in the upright position for some time now but this morning it ground to a halt. It was if the motor had burned out. I turned it upside down and some small stones etc tumbled out. I tried switching on again and the motor kicked in but the smell was horrendous so i switched off immediately. If it's likely to be **** inside the motor area i don't no how to access it. I've removed for fixing screws but still unable to prise apart. Is it just the


Hi.\015\012\015\012Try this site http://dysonmanuals.llc.nu/ has service manuals covering removing the Dc07 motor. ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

It works well until it bumbs a wall. When it backs up it will not go forward again. I took it apart and noticed a cable is lose. I dont know where this cable hooks up to. One end is on a plastic disc on the end of the motor. The other end looks to have been pulled lose from somewhere. Its only about an inch and half long.


... iRobot Roomba 560 Robotic Vacuum

I have a morphy richards upright hoover model 7333 and i cant get to the belt to see if it is either broken or just come off the runners, i have lost my instructions and cant get the things apart to have a look, does anyone know anything about these hoovers? many thanks, Carina.


... Hoover Vacuums

I took apart my 1697 model cleaner to check the hoses for leaks now I dont know if I put the hoses back on right. I cant find a diagram on how it is suppose to look.


I found a manual that has an assembly guide for your model:\015\012http://www.bissell.com/downloadfile.aspx?id=554\015\012\015\012\015\012\015\012\015 ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Hi I have a eureka 410 series lightweight upright and I took it apart to clean the dust from inside and on the very bottom of the handle the is a metal clip and a white straight plastic peice that fell out and I dont know how it goes back in.


... Eureka Whirlwind 410 Bagless Upright Cyclonic Vacuum

My Dyson will not turn on unless I pull the handle back. I have take the entire vacum apart cleaned all blockage and it still will not turn on in the upright position.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Dyson Animal is stuck in the upright position. Do you know how I get it to tilt?


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Yellow Dyson handle stuck in down position will not click upright


... Dyson DC07 Bagless Upright Cyclonic Vacuum

The vacuum is making a noise like something is stuck when it is in the carpet position but not when in the floor position. I can't find anything that is stuck in the areas that I can see. I have cleaned the brush but it does not seem to want to turn. Does this machine need to be oiled so the roller will turn? Is there a way to check inside the motor? Do you think that because the brush won't turn that is making the noise? Do you know of any repair shops in the Lake Havasu City, Arizona area?


As far as the roller brush goes, yes, it does need to be cleaned. Follow the directions to remove it and clean as best you can of all debris. On both ends of the roller brush there will be two "holders" of sort that connect the brush to the frame o ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old


Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hi there I have a spider bite on my neck, it bit me about 2 weeks ago. I have been using traxer or x-trax which draws the venom out on a daily basis. The area is not really getting better, it is still red and its almost peeling. I am currently sick and don't know if that might possibly be because of the bite, I am nauseas and have an aching body. I don't know if its just flu or if its because of the bite, it was black and looked poisonous, I have been looking at pictures and would most liken it


... Sawyer Products The Extractor for Snake, Bee, Spider and Other Bites

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?


... Dyson DC25 Animal Bagless Upright Vacuum

Dyson DC28 Air Muscle Vacuum that is stuck in upright position


This turns out to be an easy fix.\015\012\015\012First, get some graphite lube. \015\012\015\012Lay the vac on it's 'face'. \015\012\015\0121) On the underside of the vacuum, there is a 1/2" wide 'groove" in the ... Vacuums

Dyson stuck in upright position


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Bissel steamer I took the base of the steamer apart and had trouble putting back together. The switch assembly the adjusts the flow of soap came apart. I dont know how to line up the the black valve to the switch. [email protected]


You can do this Jeremy just be take your time be patient and keep trying! ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Dyson DC28 handle stuck in upright position - Dyson Ball DC24 Bagless Upright Vacuum


You DO NOT have to take your machine to a "certified technician" to fix this problem. Stand behind your machine, lean over and look at the front: Right in the center of the opening between the machine and the beater bar head, you will see ... Dyson Ball DC24 Bagless Upright Vacuum

My Dyson DC25 got stuck and wouldn't return to the upright position, I figured out that one side had jumped the track and gotten stuck in the square hole below the track. I did not want to break the plastic to force it back, so I removed the screw on the right side that was holding the kick stand on and removed the kick stand, also a spring thing came out. Problem is, now I have no idea how to re-install the kickstand. Can't find a technical manual or video anywhere, it can't be very difficul


... Dyson DC25 All Floors Bagless Upright Vacuum

I have an Air Track plus vacuum cleaner and something has got stuck between the flexible part of the hose and the solid black section at the end. I tried to put a coin down to clear it but that has got stuck too. It looks like the rigid section should come apart (a small notch each side) but I can't figure how to do this.


... Samsung Vacuums

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o


Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Upholstery attachment The nozzle doesn't spray properly, the water just pours out (not alot) instead of spraying. It also has very low suction. The upright part seems to be working fine. I cannot figure out how to take it apart so I can look for a clog, when I look into the hose I don't see anything.


May have a problem in the noozle asm on the hose. Hose part #90001335. \015\012 \015\012 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0804 seconds