Having problems with your Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum ?

The belt keeps slipping off. I bought a new one and it too slips off after about a half hour of vacuuming.

Answers :

Check the motor shaft for loosness. when the bearings wear out and fail, the motor shaft will not be strait and the belt will ride off. also check for alignment and inspect the brushroll for proper installation, free rotation, and non melted endcaps. let me know if you have any questions
Repair Help & Product Troubleshooting for Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The belt keeps slipping off. I bought a new one and it too slips off after about a half hour of vacuuming.

Check the motor shaft for loosness. when the bearings wear out and fail, the motor shaft will not be strait and the belt will ride off. also check for alignment and inspect the brushroll for proper installation, free rotation, and non melted endcaps. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

New Eureka vacuum cleaner belt keeps slipping off

You may have a bad brush roll, part #61250-1, or the base itself has a problem and isn't letting the brush roll sit straight so it can be in alignment. ... Vacuums

My hoover Wind Tunnel vacuum cleaner's motor spindle keeps overheating. Because of the high temperature, it keeps burning through belts (the big, wide ones). I have taken it in to the vacuum repair shop about three times now, and the problem has never been fixed. Does anyone have any advice on how to fix this or should I just buy a new vacuum?

... Vacuums

My Eureka Airspeed vacuum keeps shutting off after about 5 min...It takes for about 3 days to vacuum because it will not turn back on for several hours...and it is not clogged. What is the problem

... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

My Shop Vac (Brand) Mdl#934-16-11 keeps shutting off while I'm dry vacuuming. I can turn it back on then it will shut off again. The filter is spotless, so that's not the issue. There isn't any reset buttons. The only thing I can think of is that the float for wet vacuuming is somehow being sucked up causing the the motor to be tripped off. The vacuum is only about a year and a half old and used only sparingly. Help!

... Vacuums

Hover Elite Rewind I've only had this vacuum a few months and I really liked it until now. There is almost no suction from anywhere in the vacuum, and I've cleaned all the filters and rollers with my shop vac and made sure that everything was assembled correctly. It used to be really quiet now it is quite loud and it keeps over heating, and shutting off. At this point I have no idea what could cause this problem, the machine is nearly brand new and I can't afford a new one at this point.

You have to clean out the hose under the bottom of the vacuum cleaner. To do this you have to remove the bottom plate the covers the brush it has about 6 screws. Also remove the brush and belt in order to thourhly clean it. I had the same issue you h ... Vacuums

I am a professional maid and one of my clients just had her Hoover Elite Vacuum belt break. I bought the belts ... but cannot find a manual online and do not know what the model number is. I am scheduled to be in her home in exactly one hour! HELP! HOW DO I CHANGE THE BELT -WHEN I CANNOT FIND A MANUAL? Many Thanks! Lynn

This is no problem! You will need a flat blade screwdriver and about 10 minutes! \015\012 \015\012*Always use genuine hoover parts for repairs, discount store belts can be as much as \015\0121" longer than OEM parts ... Hoover Elite U5061-900 Bagged Upright Vacuum

I have an electrolux twin clean cyclonic vacuum cleaner (blue) that turned itself off. I've waited over half an hour an turned it back on. All that happens is the red filter light and the power flash. I have cleaned all filters and replaced them. The vacuum is only 5 months old.

... Electrolux Vacuums

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

Oreck xl 2100 vacuum belt keep on slipping - Oreck Xl 2100 Bagged Upright Vacuum

... Oreck Xl 2100 Bagged Upright Vacuum

Any tricks to putting on a central vacuum hose sock? The last one took me 4 hours and I'm sure there must be an easier solution. It has no zipper.

Send it back and get one with a zipper. :) Okay did it come in a tube or with a tube? They are really necessary when putting a hose sock on. You first want to put the hose sock on the tube. You then slide the tube over the hose and take the hose ... Electrolux Central Vacuum

Cyclovac dl-200 sv control card blew,why? Changed card installed new card different rev. ,rev.c instead of rev.e fuse on card keeps tripping vacuum only operates on one speed high.

... Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.

I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

My Hoover Windtunnel cuts off after using it for a few minutes. After an hour or so, I can turn it back on again. This keeps happening every time I use it. This is my third one. I have taken the other two back to Target for the same problem and they have exchanged them.

Yes this machine has a thermal protector in it to shut off the machine if it gets to hot, this is normal. if there is no clogs in the hoses or in the machine then you will need to wash the filter at the top of the machine. you will have to remove the ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

My Eureka Maxima 4704 pink vacuum is really squalling .. its so loud you need ear plugs .. we just got the thing Christmas .. and has been used under normal conditions..we keep the filter clean and even recently washed it and let it dry for 12 hrs to see if that was the problem but it wasn't what else could be the problem ... I do not think that the belt is slipping because I can't smell rubber burning ...IM STUMPED

... Vacuums

Where do the belts go one busted in half - Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Confirm your model number, then check http://www.bissell.com/SearchResults.aspx?searchtext=proheat%20&mode=userguides ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks

You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?

The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v

I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

I have a DC17 which is only one year old. Today I lost suction and called for assistance. A Dyson technician told me to pull off the wand and see if it is clear. It was clogged so cleared out the obstruction. My filter was cleaned more than 24 hours ago. The vacuum still has no suction. Is it dead, any other suggestions. Please help.

Take the hoses off and give them a good shaking.\012or get a long piece of stiff wire and gently poke through the obstruction. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

THE LARGE BELT KEEPS SLIPPING OFF. It doesn't seem to matter what I'm vacuuming - carpet or hardwood.

Hi there SmartAlec from NelsonVacuums.com.au there are 2 basic causes for this to happen. 1. The belt has become stretched over time (can be as short as a few months) ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.

The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

It keeps cutting out with no power and then will start again for a while half an hour later. suction isn't as good as should be

It sounds as though you are overloading the motor and it is tripping out,check for blockages ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly

... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0966 seconds