Having problems with your Dorman 2000 Chevrolet Blazer Switch / Front Axle 4WD Switch ?
2000 chevy blazer 4wd stumble stall on start and idle
\015 Ran beautiful til I had some work done went home with problem afterward stuble stall on start, run great until idle at a light, hesitate/miss on acceleration then recovers. Checked plugs and wires. Not setting off the engine check light. My sense was the mechanic created the problem, something simple, but wanted to make another 500 to fix it. No drips or leaks, no other indications of anything wrong. Tried dry gas treatment some inorovement on running but not the stumbles.\015
Its not The mechanics fault all the time, you may fix something then something else goes wrong thats mechanics 101. I've had this problem before I replaced my ignition coil and my fuel pump, fixed it right up in my 96 f150. Give it a try its a whole lot cheaper than most options.
Repair Help & Product Troubleshooting for Dorman 2000 Chevrolet Blazer Switch / Front Axle 4WD Switch
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
2000 chevy blazer 4wd stumble stall on start and idle
Its not The mechanics fault all the time, you may fix something then something else goes wrong thats mechanics 101. I've had this problem before I replaced my ignition coil and my fuel pump, fixed it right up in my 96 f150. Give it a try its a whole ... Dorman 2000 Chevrolet Blazer Switch / Front Axle 4WD Switch
Car dies when u put it in gear but u can drive it but when u go to stop it will die it is a 1992 chevy camaro rs 350 throttle body with brake booster vacum un done it will sit and idle with it on it will idle for about 3 mins. but with it off it will still die when u put it in gear what do i need to do john henry sparta tnn. 38583 (931)808-3624 cell phone i have tried everything i know to do ????????
Go to autozone and buy you 2 bottles of heat and put it in the gas tank.it sounds like you have built up some condensation in you tank an its pumpimg the water thats accumulated in you gas tank.put the 2 bottles in the gas and it will dry up the wate ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum
Need vacuum scematic for 1992 chevy S10 blazer
Car starts fine! But will not idle and remain on.
Hi, This could be several problems but i'll need to know what make and model and if it is diesel or petrol!! (If petrol is it injection or carb) Once i have this information i will be able to assist you further! Your lucky that i'm a mechanic b ... Vacuums
With a/c on max, and either excellarating or accending I seem to lose vacuum and vent goes to defrost , then when slowing down it goes back to normal settings. , check valve new, vacuum ball no leaks ????? blazer s10 1997 4wd
You need to repost this in the auto. repair section, this is for vacuum cleaner repairs. ... Vacuums
I got this sewing machine , can anyone tell me what this control box is used for ?. It is mounted under the table in front of the motor,It says Control Box on the front and two push button number settings with can be adjusted up or down from ( 0 to 9 ) ,Next to these settings are two toggle switches. One is marked start with on and off and the other switch is marked end with on and off. Above these switches it it says Back Track . The tag on the box says ( Type LE -BB -24 - 110 - 220, 2
Still struggling with your model number. I understand from the added comment this is a Brother sewing machine. I was hoping to find a manual that would be of assistance. Here is a couple of websites that lists available manuals for Brother sewing ... Vacuums
Electrolux ultraactive vacuum won't start
Hi There, The E2 error is caused by the terminal block pins where the hose plugs into the vacuum become bent out of shape. This is the receiving pins at the front of the vacuum on the inside. If what I am saying is confusing then it probably needs to ... Electrolux Vacuums
Ultraactive vacuum won't start
Once again having vacuum problems, when I push the start red paddle it hesitates and won't fully starts. It makes the noice to start but then it shuts off. Makes noise to start but then promply
... Eureka 4700A Maxima Bagless Upright Vacuum
Problem starting Sometimes will not start at all. Sometimes will do a quick start and stop. Other times it starts and runs fine????
This can happen if you have an intermittent short in your cord. Try plugging it in and then wiggling the cord around where it goes into the body of the vacuum with the switch set to "on." (If you're not sure whether it's on or off, just click it back ... Dyson DC07 Bagless Upright Cyclonic Vacuum
My Singer Izek sewing machine starts and stops and wont sew continuously. When I push down the pedal it sews about 2 inches then stops and light starts flashing, I have to let off of the pedal and push it again, over and over. It did this once before for awhile and then just started sewing right for awhile and now its started it again. I've checked everything.
If it's not the thread and not the pedal then it's definitely a power problem. You need to replace the power cable and then check again the functionality. ... Vacuums
Webpage error detailsrn User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; FDM; AskTbPLTV52/18.104.22.16849) Timestamp: Wed, 1 Jun 2011 21:06:26 UTC Message: HTML Parsing Error: Unable to modify the parent container element before the child element is closed (KB927917) Line: 0 Char: 0 Code: 0 URI: http://www.facebook.com/hoshmend.ali1
... Euro-Pro PT205 Leaf Blower Powerful 12 AMP Leaf Blower, provides 205MPH air speed, Detachable Vaccum... Vacuum
Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian
... Electrolux Vacuums
I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.
Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum
My Dyson DC07 vacuum started to run slower after being on for a little while and then would run normally again. I have switched on today and it has just stopped. When I push the start button, on occasions it almost starts and then doesn't. I am wondering if there is a problem with the switch and if so how can it be fixed? Thankyou.
The motor running slower was the motor starting to burn out. The "almost start" is the brushes making intermittent contact with the armature in the motor. \015\012\015\012Your machine needs a new motor Pam. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob
Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum
Won't start I have a miele, model # s2481 red vacuum. It will not start. When the button is pressed it feels normal, but nothing happens, it will not start. Is this a problem my handy husband can tackle?
It is most likely your cord winder. They are a little tricky to fix yourself. A repair shop will probably charge about $50. To fix it. The contacts where the cord winder plugs into the motor need to be cleaned and adjusted. Just don't let your r ... Vacuums
While using my Dyson a rug got caught and that ratcheting sound started. I removed all signs of strings, etc until the brushes rotated fine but when I started the Dyson the ratcheting started again. I have the DC 14 Animal.
The rattly sound means the drive belt has snapped or the protective clutch has slipped. This needs repair by someone who knows how to repair Dysons officially. Sadly its the kind of model that can't be done by the owner. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Hoover u5781-900, motor shuts off (intermittent)when you shake vac or make jerky movements.If you move vac to up right position the vac starts right up.When you giggle vac, motor starts and stops no mater if you just started up or vac for ran for 45 min. Thanks Lucy C.
Lucy\015\012you have a bad connection somewhere in the unit\015\012this is a fire hazard and you should not use this until its been fixed\015\012could be a pinched wire or broken connections ... Vacuums
When I turn it on it doesn't start out in the circle motion but starts and than stops and than starts and than stops and moves erratically and than totally stops.
Try a different battery. If no go, you might have bad board or sensors. Basically, if the battery replacement doesn't fix it, get rid of it. Borrow a battery from someone else so you're not wasting your money for testing.\015\012\015\012-=/ Daf ... iRobot 5800 Scooba Vacuum
I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.
My new H2O Mop Ultra (Danoz) seems to heat up ok then when the light switches to green and I start using it, the orange light comes back on as well as the green. Produces steam to start with but then it starts to spit water too and everything ends up wet. Any ideas on whats wrong or should I just send it back?
That is a major hardware fault, I have seen this numerous times with these H2O mop's... They seem to either work perfectly for a long while or have problems right off the bat. You definitely want to send this unit back and either get a refund or at ... Vacuums
My scooba when switched on starts to spray water then spins round faster than normal then starts to go backwards quite quickly then stops then continues to reverse more then stops & with the nor
... iRobot 5800 Scooba Vacuum
Chain saw starts runs, bur saw won't start next time it is needed, craftsman chain saw
Steam vacuum? no clue but on your chain saw make sure you check the choke. it would explain why it wouldn't start again. ... McCulloch MC1275 Steam Vacuum
My Dyson DC28 Beater Bar will stop turning then start again. Then it quits all together and after awhile it will start again.
Hi there, it's Jack at Dyson.I'm sorry to hear your DC28's brush bar seems to be working intermittently. It may be worth taking a look at the video I've attached below, as this shows the correct way to check the cleaner head for obstructions ... Dyson DC28 Animal Bagless Upright Vacuum