Having problems with your dyson ?
why does my hoover keep making a screeching nois
Hoover making screeching noise when hoovering up
Repair Help & Product Troubleshooting for dyson
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have vax 3:g red light keeps coming on and hoover makes funny noise. cleaned filters but no change.what else should i do
... Hoover U6476-910 WindTunnel Upright Vacuum Cleaner Bagged Vacuum
The powerhead on my Dirt Devil keeps cutting out, and after a few minutes, making a burning rubber smell. Only used it less than a dozen times (same thing happened with my Hoover!) It is free of hair etc...
Sounds like you've done a lot of troubleshooting on this unit. It could be that the bushings are worn and the "play" in them is causing them to seize (this is often accompanied by a chattering sound from the bushings).\015\012\015\012I w ... Vacuums
Hello. My dyson dc04 keeps making a loud screeching noise when im vacuuming. It seems as though the plastic from the brush is catching on the plastic on its holder either side of the belt. Is there any way of fixing this problem?
Remove base cover by 3 'screws' 1/2 turn anti clockwise and clean well remove fibres replace cover and re try. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a
The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hoover windtunnel Not sure of model number- but brush roller clamps down on carpet being vacuumed and stops spinning regardless of which of the 3 height selections is selected. Can make it work by leveraging the handle down (or back towards me) to keep the cleaning head a little off of the carpet-any suggestions or ideas?
Would suggest the drive belt is stretched and thus is slipping when contact is made with the carpet. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
The filter in the ball keeps popping out when hoovering up which makes the ball v hard to roll
... Dyson DC25 Animal Bagless Upright Vacuum
I am using a hoover steam vac and the button keeps popping up to say that the water is full. That makes the thing stop sucking up water out of the carpet. Problem is, it has barely sucked up any water yet. Help!
Have u tried cleaning it out really good make sure any areas that water is **** up through are free of hair, lint ect. ... Hoover Vacuums
Hoover steam vac ultra makes aloud screeching sound when turned on. Sounds like noise is coming from motor. can this be fixed?
It has a bad motor ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Hoover linx motor makes a lot of noise when running
... Hoover Platinum LiNX Cordless Stick Vacuum
Hoover vaccum is screeching loud
... Hoover Flair Bagless Vacuum with Powered Nozzle
My Miele vacuum cleaner has the red triangle light on and keeps switching on and off. Is it broken? have been hoovering upstairs and I noticed the hoover had the red triangle light on. I changed the hoover bag but it still kept going on and off. Is this an overheating problem or is the hoover on the way out?
... Miele Vacuums
Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest
I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum
My dyson d14 animal keeps cutting in and out. When it's on, the hole above where the filter is, keeps making a loud suction noise and it won't clean up hair and dirt.
Vacuum Cleaners require AIr-Flow. Your machine is not getting any air-flow. The noise you hear is a valve opening up to prevent your machine from overheating and burning out the motor. You probably have an obstruction somewhere in the machine. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
Hoover Windtunnel - the belt keeps coming off & it is the correct
One compatible belt that I use and works (at least while its new) is Royal 104425001. Try that. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
Hoover makes terrible screaching sound when using upright.
Install new belt(if still makes noise change bearings) ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I usemy hoover often, and last time I went to use it, it keeps blowing the circuit. It has never done this before, not in any of the plugins used, hoover or electrical problem?
It may be the motor is starting to short ... Hoover F7431-900 SteamVac Vacuum
When i turn my hoover on and start hoovering the cable inside makes a clicking noise and goes off and comes back on when i move the cable. I have only had it for 3 months
Almost certainly a warranty issue. Take it back to wherever you bought it. ... Numatic Henry Bagged Canister Vacuum
My hoover makes a lot of noise, how can I make it quieter?
Is it making a grinding noise? if it is check the brushroll, it might be siezed up and the clutch is grinding in an attempt to protect your belts. ... Dyson DC14 Bagless Upright Cyclonic Vacuum
Hoover 1900w keeps cutting out - Hoover Vacuums
Opened it up little senser near the moter on a wire moved away from the motor dont cut out anymore ... Hoover Vacuums
I have a dyson hoover. up to last week it worked fine. now it will not hoover up bits!!! i have to keep taking the long attahcment off and using that instead which is not ideal!! hubby has checked underneath..all brushes seem to be rotating fine and its not the belt. any suggestions?
Check the inspection air tubes on the Dyson - you don't say what model this is - and each model does have air inspection tubes but can be different to each model - which can usually clog up with dirt/debris thus making the machine difficult to pick u ... Hoover Vacuums
Hi, When changing to brush mode when hoovering, the hoover makes a terrible noise like something is catching
They all make that noise everyone i have ever used does this. Dont know why but has never effected the performance. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Vax hoover my vax hoover keeps overheating and cutting out.
Powerhead woes Drive belt for power head beater brush on Hoover S3755 keeps jumping off drive motor shaft when vacuuming low pile carpets like oriental rugs unless minimal suction is used. Any tricks to keeping the belt in place other than this?
I've had my Hoover S3755 for about 2 years and loved it, at least until the last couple of months when the "belt slipping off" problem started. I changed the belt and the vacuum would work for a little while then the belt would come off again. I pu ... Hoover S3755 WindTunnel Bagless Canister Vacuum
I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi
Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums
I have a DC04 which is a number of years old and has started making an awful grinding sound, I'm sure it is the belt which I sprayed with WD40 and this helped for a couple of seconds but as soon as I recline the hoover it makes this noise but not when upright and using the hose. Does anyone have any ideas or how to change the belt? Thanks
You have to change the belt look it up with your local vacuum store. ... Vacuums