Having problems with your Dyson Bagless Upright Vacuum DC41 Animal ?
Brush wont work
\015 Little over a year old. No previous problems, but when I started to vacuum, the brush will not work. Why?\015
Probably the belt. Cannot by it separately though. As of Aug 7,2013 you still have to buy the entire brush assembly 920774-01 for 111.99. Rediculious when all I need is a little rubber toothed belt.. (belt part 20724-01-01)
Repair Help & Product Troubleshooting for Dyson Bagless Upright Vacuum DC41 Animal
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do i get the brushes to work again on my steam vac it all works other than the brushes ....the brushes wont spin
The scrub brushes won't spin on my Hoover F5915-900. ... Hoover SteamVac V2 6-Brush Widepath F7426-900 Vacuum
DC07 brush wont spin on bottom, took all apart and wont work
Hithe belt is broken or stretched, replace it ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Hoover F7431-900 steam vac brushes wont work
The brushes are activated by suction, my berings and gears froze up, i took it apart, kinda hard to figure out, but not as bad as it looks. i lubed the berings and the gears, then i took an air compressor to the activation fins and let it spin, lubed ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
Why wont the brushes spin? I have had this machine for about 3 years and it has always worked great, tonight the brushes will not spin at all, it still sprays and sucks up the water. We took the brushes off and were able to spin them by hand
In this machine there is no belt. The brushes actually spin by vacuum and in the turbine assembly there is a small wheel bearign which rusts out. You will need to remove and repair or replace the turbine and gear assembly P/N should be 43191009 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Miele power plus brush model seb234/236 won't work and telescoping wand wont stay xtended
Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks
If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum
The brush does not work on my dc15 animal, there is great suction but after about 20 seconds it sounds like something has got blocked in it although nothing is clogged, filters and hoses have all been cleaned but the brush still wont go round
Hi there,Sorry to hear you're having a problem with your DC15. You might find it helpful to visit the Support section of our website and follow these simple steps: ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Brush wont work
Probably the belt. Cannot by it separately though. As of Aug 7,2013 you still have to buy the entire brush assembly 920774-01 for 111.99. Rediculious when all I need is a little rubber toothed belt.. (belt part 20724-01-01) ... Dyson Bagless Upright Vacuum DC41 Animal
Brush wont work on vax mach 7
Beater brushes wont work
Sounds like you really need a new belt. Don't know why it is taking so long for you to get one. But belts stretch and then won't turn the brush roll under load. Call around to your local repair shops, must will a good selection of belts on hand. ... Vacuums
MY vaccuum wont suction or turn at the brush bar. The wand works and I already checked/cleaned all the areas the instrucion manual said to.
The DC07 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" (or "off") and "carpet" (or "auto"). The roller will turn only when the knob is on "carpet", and even then only w ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Dyson dc04 wont pick up,motor working,replaced clutch assembly but still dosnt turn brushes
You need to go through a process of elimination. You are better doing that here: Dyson advice forums ... Dyson DC07 Bagless Upright Cyclonic Vacuum
I have a hoover upright vacuum 1 year old and the brushes wont spin but the attachments will still work
Change the belts and if it still doesnt work theres a problem with the motor ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum
I have a Bissell Proheat 2x cleaner which has worked perfectly on every occasion. Today I filled the machine as usual with water and formula and switched on, the motor ran, the lights were on and the brushes rotated but upon pressing the spray trigger no water or formula was released. I have cleaned the jets underneath and also followed instructions to release any airlock. It still wont release the water/formula. What else can I do? Thanks Charles
Please check the following with liquid in both tanks.\015\012 \015\012- Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.\015\012- ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
VACCUUM GOES ON, MOTOR WORKS, BRUSH WONT TURN WHEN THE VACCUM IS TURNED ON.
Check the belt, and remove any objects clogged in the roller system ... Dyson Vacuums
We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?
Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums
Why wont the self propelled brush on the hoover wind tunnel work. large belt is ok. the small belt looks 0k.
No don't do that,have a little patience.check where the self propelled assembly is and see if anything got in there,something might be loose and the teeth are meeting each other.thats a good vavuum.i have 2 but their not self propelled.try taking the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Roller brush bar wont turn after te machine made a popping noise then just only the vaccum is now working
I had this exact problem after moving the machine by car. after opening the machine there is some dampness so suspect popping was caused by liquid mixing with electricity. The machine does have drain holes so leave it upright for a week or two and t ... Bissell 9200 Upright Vacuum
I can't get the brushes to rotate on my hoover steam vac v. i took them apart and cleaned them and they still wont work. any ideas?
Scrubbing brushes are driven by a belt. The belt either broke or slipped off its pulley. ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum
Brush wont work - Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
You probably need to change the belt. You can get a replacement here:Bissell Healthy Home Belt ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue
The vacuum suction still works but the brush wont turn. It still looks like the belt is intact and attached properly.
The problem with Dysons is that the belt breaks and sits in position.If you can turn the brush by hand, with little or no resistance then I would say the belts broken.If in doubt take the cover off and look. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a hoover savvy that the rollers wont turn. I've taken it apart to make sure the brushes are not caught but nothing happens. I only used this vacuum once. It was a floor model when purchased. I just need to figure out what I need to do to get this to work.
Hi there SmartAlec from NelsonVacuums.com.au here. I have to say that if it is not as simple as a belt - I assume that when you checked that the brushes weren't caught that ... Hoover U8125-900 Savvy Bagged Upright Vacuum
Dyson dc14 animal is falling apart! The canister keeps falling our and now the carpet/floor adjuster doesn't work AND the brush wont turn....tried everything. I live in Half Moon Bay, CA (near San Francisco) where can I bring it to be OVERHAULED? Thanks
The best sol would be to search for vacuum repair half moon bay, ca. To see if there is a vac shop near you. my suggestion's would be either Vacuum Cleaner Shop #(877) 822-8227 or Vacuum solotions #(502) 348-4900. hope this helps ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
When I turned on the sweeper it would not start. I put a different power cord on it and it worked fine. now it won't start but the light on the brush and the bag full will flash when i turn it on and off but it wont start. i have 2 of these doing the same thing. do you have any idea what could be wrong. I have checked for clogs but have found none. Bob
Its sounds to me like the computer board inside the machine has gone bad. Keep in mind that the filters in these machine do need to be replaced regularly to keep the vacuum working correctly. Any good vacuum shop should be able to fix your problem. R ... Windsor SR12 Sensor Bagged Upright Vacuum
Wont **** the beater brush works but it's not sucking stuff into the canister
Sounds like a blockage some where take apart the hoese and clean them one at a time ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum