Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?

I am unable to get the handle off the top to use the hose. what to do?

Answers :

Take a look at this video ..at one point they show how to remove the handle ...On this model it comes out with the bar ..and the hose will extend from inside...It has a locking device at the side..and will probably need a slight rotating move to get it out ..
There is a yellow button at the top of the unit that you have to push to release the handle.
Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am unable to get the handle off the top to use the hose. what to do?

Http://www.youtube.com/watch?v=Mm4rFq71zHA&feature=channelTake a look at this video ..at one point they show how to remove the hand ... Dyson Ball DC24 Bagless Upright Vacuum

My infinity vac NV29 seems to have an extension wand stuck down in then tube and I am not able to get it out. We rented our winter home and evidently they found some type of extension that did not belong to it. Is there a way to take the handle apart in order to remove it? I am not able to use it with the handle and have to use the one on top of the canister, which is extremly difficult for me since I am disabled. Thank you.

... Euro-Pro Vacuums

Frozen top The top of my Shark sc505 is on so tight that I cannot get it off even with heavy duty tools. It appears to be frozen and will not move. How can I get it off so I can use it again?

I just bought one from a thrift store we were able to get the top off! We used wd 40 and vice grips and it came off. The machine looks like it was only used once and someone left the water in it. I immediately put white vinegar in it and rinsed it ou ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???

Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

I have an elna 3007 machine. Our service man died and I need help with the tension. I can't get the top tension number to change off zero. when I free motion, all I get are loops top and bottom. I have adjusted the machine the best I can but still have the problem. I'm in the middle of a quilt and could use some help.

... Elna Vacuums

I just bought a used euro pro steam shark model ep903, has all parts but when I turned it on to use it water and steam poured out of the handle grip area. Am I not doing something right? The manual says to attach the brush directly to the hand grip but I can't use it without getting burned. Any suggestions would be greatly appreciated! Thanks!

... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu

This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?

You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

Broken/snapped off handle with minimal use...twice...two differen

Hi,The shark has a one year warranty... send it back ...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

The screw that holds the handle to the top of the canister came completely loose. How do I get to it to reattach?

Buy a epoxy cement and fill the hole with it, then drill a hole a little smaller than the screw, and finally insert screw. ... Vacuums

The top of the vacuum cleaner gets very! hot with little use of hand wand. it is a majestic model with chrome top about 6 years old

The exhaust is from the top so it will normally get pretty hot. If the machine shuts off, then there is a clog, or a full bag. Most of your machine is actually plastic, so examine it closely for warping or any discoloring. Also if it sounds funny yo ... Vacuums

Just got a Polti Vaporetto 1020 from someone and cannot get it to work. One yellow light lit up and was on for a few minutes then turned off...and there is nothing...flip the switch on the handle, nothing...flipped other yellow button, nothing...any suggestions? or where I might get directions on how to use it? didn't come with manual. Many thanks. best, pat

... Polti Vaporetto 2400 Canister Steam Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

I have an edic aqua fresh box extractor and I'm trying to use it....however I do not have the manual on how to operate it. There are instructions on top of it, but they are partially ripped off and faded. After setting it up and trying to use it, I don't seem to be getting any suction. Any advice or help?

... Vacuums

Hi, having problems with my Dyson DC27. It's worked very well for the last few years but recently i can't get the handle to stay attached to the base after using the wand causing the handle to

Hi there, it's Jack at Dyson.I'm surprised to hear that your wand isn't staying attached in use - it's engineered to lock securely to the machine when you replace it after use. Like all of our upright and cylinder vacuums, DC27 has a ... Dyson DC27 Bagless Upright Vacuum

We have bissell pro heat and I have put new belts on and took off the top plastic cover I blew out the lines and I still can't get it to pump water or solution. The red little spinner flow indicater does'nt get water, if I pour water into it it runs out the front. I guess I don't know what else to do. The machine worked fine the last time we used it about 6 months ago. Any suggesttions?

Did you check and make sure the belt is still on right? They do come off from time to time.There are like 6 long screws holding the top cover to the bottom. The are real pain in the behind to put back together once you take them off. T ... Bissell Vacuums

While using, steam stopped coming out in force at the port levels in the head. Suddenly started high pitch whining, pressed button just above connection site and end flew off with great force pouring water onto floor and carpet. Unplugged immediately for safety and unable to get it to deliver steam force again. Less than one year old and used only 8-10 times only in walk areas where there is no carpet with distilled water. Please, advise, cannot find booklet. Thanks So Much, Beverly Crumme

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Last year my wife and I bought a new Dirt Devil Reaction All Surface vaccuum cleaner to replace the older Platinum Force. After using it a couple of times the new one gets clogged with dog hair easily and shuts down. I cleaned it out completely including the hepa filter but it will not handle the dog hair. The old one never had a problem and still works. We went back to using the old vaccuum cleaner because we can not find the receipt and had not registered the new one and are stuck with a new 1

Greetings jettin_us,\015\012\015\012Normally you can contact the store you purchased the unit at, and if you paid with anything other than cash, they may be able to retrieve your receipt for you. \015\012\015\012Once you get t ... Vacuums

Cap (top) is froze. Unable to remove cap (top) to pour water inside for use. not sure if model specified is correct. It's a canister with hose and multiple attachments for cleaning.

I too can not figure out how to get the lid off. ... Euro-Pro Shark SC-505 Handheld Steam Vacuum

Hoover floormate Hi, I'm not sure what the model number is on my Hoover Floormate, but I can't get the cleaning liquid to dispense. The vacuum(dry pickup works fine). The handle squeezes without a problem. It used to work without a problem and then I didn't use it for awhile. When I came back to it, it wasn't working. Thanks, Alissa

The tank sits on what is called the reservior asm. it is actuated by the control rod inside the handle. With the tank off, watch and see if you can see that rod hitting the reservior asm when you squeeze the trigger. If it is moving up and down on ... Hoover Floormate H3000 Upright Wet/Dry Vacuum

I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t

... Dyson DC25 Vacuum

I have a old nilfisk GM 90. Still going very well, but it fell last week and the handle on the top broke off. I would be delighted to have this repaired, so I hope I can still get spare parts for these wonderful hoovers. Eileen Corcoran

... Nilfisk Vacuums

Bought a cyclonic unable to get the handle to telescope

Being new, take it back for a different one or take it in for warranty repair. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0832 seconds