Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?

Something has clogged the vacuum and I misplaced the manual. How do I unclog the machine?

Answers :

Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Something has clogged the vacuum and I misplaced the manual. How do I unclog the machine?

... Dyson Ball DC24 Bagless Upright Vacuum

I have two older Filter Queen (brown vacuum cleaners). Besides unclogging the hose area and making sure it is not filled with dirt, what else would cause the machine to run hot and have a high pitched sound? Is there another area where I might have clogs?

There is a secondary filter under the paper cone that gets filled with fine dust. It can choke off the airflow. The noise motor sounds like a bearing going dry. That should be replaced ... Filter Queen Majestic Canister Vacuum

I have bissell powerforce turbo bagless upright vacuum. Its a great machine. It is clogged though. I think I was not emptying the dirt collection tray thing enough. How can I unclog it. Its not sucking up like it should. It sucks up most stuff, but its not going into the bagless tray thing like it should

Remove the hose , clear that , then if you take a wire hanger apart you can pull whatever is remaining out of that connection, also remember to clean ( if you have the cleanable filter) the filter and also the top one ... Bissell Vacuums

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]

Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Clogged vacuum Rather stupidly, my boyfriend 1) were vacuuming without a bag and 2) vacuumed up a big piece of cotton from a sofa cushion. And now it's making a horrible noise and I see it vibrating where the tube connects to the machine. When you look inside there's a white thing sticking out but it looks like it's part of the vacuum. If it's a clog, how do you fix it? I tried unscrewing the tray the bag sits in but it won't budge.

You can start by taking off the bottom plate or top cover, which ever comes off, that is where the inlet starts going in and hopefully the clog is there. Could be in the hose also. But without the complete model number I can't look it up to see a p ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

Clogged Bissell After debris clears the brush part, it gets clogged at the point of entrance into the machine, barely anything makes it through the filter and into the canister. Clogs immediately after a few swipes of the carpet. Had vacuum for almost 3 years.

Something must be in the hose causing a clog, take the hose off and if suction is good where the hose hooks up, then there is something caught inside the hose. ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I can't get the vacuum to **** and can't get to the point of the clog. The pieces don't come off. Also need to know how to get the filter piece off the machine.

This link is for the manualhttp://www.dysonmedic.com/PDF%20docs/dyson_dc18_owners_manual.pdf ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I recently purchased a bissell proheat 2x and have used it several times with great results, the problem I am now having is no water being released from the bottom of the machine and the gauge is not spinning. What could be the problem. I have taken the machine apart thinking maybe something is clogging it.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The motor just went out on my 2 year old vacuum with light usage (hardwood floors in a very small house.) The Sears repairpeople are estimating ~ $130 to fix (this includes parts & labor). I'm wondering if it's worth investing $130 into something i've spent $350 on only 2 years ago. Shouldn't these machines last longer ? Is there something I could do to get them repair free as it seems the motor must have been faulty to only have lasted 2 years. Thoughts ?

Aye, get a dyson, if its out of warranty there's not much u can do bout it :( ... Kenmore 25512/ 25513 Progressive Canister Vacuum

I bought a used vacuum seal machine (hobart model ht-120) it does excellent vacuum but it doesnt seal correctly all the time. it seems like there is something wrong with the valve that activates the bar that goes up and makes pressure and heats the bag for complete sealing. The heating is perfect but what is not working is what make the bar go up and down.

... Vacuums

My Model number 11635923502 kenmore vacuum is making a deep suctioning noise as if something is stuck in it. We have cleaned out the filters and all the vacuum lines thinking it was clogged. It is still making this noise and we are frustrated as to what could be causing this problem. The unit does not have much suction.

... Kenmore Progressive Upright Vacuum with InteliClean System Slate Blue

No suction the vacuum runs, but there is no suction. I've checked the hose and the foot, there are no clogs there. The canister was pretty badly clogged, but I've unclogged as much of it as I can get to. it doesn't seem to come apart any more. I've cleaned the filter as well

The hose can clog up insid where you cant see it my husband takes it off and runs water thru it to flush stuff out lets it dry then reconnects it ... Dirt Devil Featherlite Bagless Vacuum M085845Vacuum

Vacuum My vacuum is loosing it's suction power. I've checked the belt and it's in perfect shape...I've bought a new filter cup...I've checked for clogs and there aren't any...I've cleaned the entire machine...and I still can't find the source of the problem.

You checked the belt, but I bet it has stretched and won't drive the brush roll under load like it should. Belts only last a few months the stretch and should be replaced. Iff you have suction at the hose, then it has to be down below, either belt/ ... Eureka Whirlwind 4480 Upright Vacuum

My HEPA filter get's blown off of the vacuum when I vacuum. I just got all new filters and a new brush roll. Could something be clogging in the inside?

There should be a cover that closes over the HEPA filter. If the cover is missing, or is there, but does not snap closed, then either snap it closed, or replace the cover.If something was clogged inside, then the HEPA filter would be less prone ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The hose is clogged in my Kenmore progressive 116.28614 vacuum. The clog is near the end of the hose -- towards the bags but below the elbow in the hose. How can I unclog it?

... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum

The vacuum became clogged and motor abruptly stopped, after unclogging vacuum will not power on.

Check the power lines coming into the suppley 9-10 the main feed came loose, you may have to solder the wire back, but there would be a short somewhere, or you ran the it to long while clogged and blew the bendix/motor ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?

... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

My vacuum has suction with the long tube assembly but not any significant suction down by the rollers. I assume there is a clog or a problem between where the hose attaches to the machine and the rollers but I can't figure out where to look for it. HELP. I've only had this vacuum for a few months and I'm really dissapointed!

Go to the bottom of the machine and to the rhs of the rollers you can see the pipe - also remove hex panel on back and remove hose from elbow , i also found that a filter cx did wonders ... Miele S7210 Bagged Upright Vacuum

I'm trying to pull the fan drive of my vacuum so I can get to the motor but Ican not seem to get it off. I was wondering if there is a release switch or something that is preventing me from doing this. Also the motor seems to be burning but I think it's because ther is something in there clogging it up.

Check to see if it has reverse threads, Most do ... Vacuums

I bought a Kenmore canister vacuum, model 116, in April 2007. This morning, the sound of the motor suddenly began to deepen, and I began to lose suction. Normally, if something is clogging the hose, the motor will wind up to a higher pitch, not a lower one. The filters are clean, the bag is empty, and I can't detect anything lodged in the hose. If this were a car's engine, I would say it's "lugging down". Any pointers?

Okay, bear with me. Is it possible you have a suction adjustment, dial somewhere on vac. Check and see and if it does, be sure it's all the way up. Also, try removing hose and run a broom handle fr. one end to the other...BUT be careful not to stretc ... Vacuums

My Oreck XL was working fine, then when I vacuumed a shag rug is started smoking and smelled like something is burning. (I changed the bag, checked for clogs--none found, and roller brush is turning. It has a metal handle.) Now I am afraid to use it.

Even though the brush is spinning, the belt is probably worn out and stretched. when you vacuum the shag carpet, it puts more drag on the brush. try running it on a shorter carpet or hard floor for a few minutes. if it doesn't smoke, then you know i ... Oreck XL2000 Bagged Upright Vacuum

I have a dc17 and there is a clog in it. I have taken the brush off, cleaned the hose, but there is something up inside the hose on the side that I can't get to. how to I take things apart so I can see to unclog it.

On the back of the vaccuum theres is a screw with a ubend hose...did you remove that? I have had things stuck in there which stopped suction? you may want to check that. also take the wand off and look through to make sure you can see light throug ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Hoover SteamVac has been doing a wonderful job but in two instances, after emptying the dirty water and reattaching the reservoir, the machine has lost suction. The first time I was able to make it work again after taking it apart and putting it back together about 10 times. I don't know what I did that fixed it but as long as it worked again, I was happy. But it's happened again and I can't get it to vacuum. I can see that it isn't clogged. Can you please help me????

Look for the lower tank filter to be clean. also make sure the lower tank lid is on properly. latch when installed on machine. Make sure the front panel duct is on the lower tank. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.

I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Dyson animal dc14 - beater spins but vacuum not working - not clogged - is there a reset or is it something else?

Hi there, if the machine is not blockage (which is the most likely cause) its possible that the internal hose has twisted, lifting the cleanerhead off of the floor slightly. To recitfy this, lie the machine on its side and you should be able to see ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1304 seconds