Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?

My vaccum motor is running brush is rotating it's just it doesn't have suction doesn't **** dust!


Answers :

If every thing is running but you have no suction than there is either a clog in the hose somewhere or the filter is plugged up and needs cleaned out or replaced
Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My vaccum motor is running brush is rotating it's just it doesn't have suction doesn't **** dust!


If every thing is running but you have no suction than there is either a clog in the hose somewhere or the filter is plugged up and needs cleaned out or replaced ... Dyson Ball DC24 Bagless Upright Vacuum

Hoover upright bagless vacum.motor runs, brush turns, no suction through hole behind brush roller. however there is suction going out of dust cannister filter flap to motor. what could possible problems be?


Sorry to read about your problem, I hope this helps you out.you have a clog between the brush and bagI tried to help you. Please help me and Rate/Vote on my response, thanks and good luck ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My kenmore vacuum model 116.36933502. It has no suction. I have cleaned out every spot,taken off the back and still nothing. The motor runs but doesnt seem to be at full power. The agitator brush works. When it broke i seemed to smell something and since it has no belt. Does this possibly have to motors?


... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I bought a G5 (w/ all the attachments) at a lawn sale. It works as in the motor seems to run fine and the brush head rotates, but.....there's no suction. Is there another button or lever I need to push/pull?


This link is for the manual it may help you.http://kirby.110mb.com/docs/kirby_sentria_manual.pdf ... Kirby G5 Bagged Upright Vacuum

Motor runs vacuum has suction on attachment but brushes won't Rotate


This problem is most often caused by a broken brush roller belt. Sometimes, although very rarely, there is a separate motor which turns the brush, or there may be something that is causing brush roller to bind so that a belt does not last long. I do ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The roller brushes do not rotate. The motor is running and the suction seems fine.


Are the brushes free of threads, lint, pet hair? If not, this can stop them from rotating. Check the outer edges near the wheel case as well. You can use tweezers to remove all the "tangler" stuff! I hope this helps. If it does, please rate my sugges ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

7600 model - motor runs and good suction present Does not self propel and brush does not rotate although I can turn it easily


Your brush drive belt has broken. Generally you need to remove the bottom of the machine in order to get to it. On the belt you should see numbers even if you don't, just look on the bag that the new one comes in for the brand and model you have. Bel ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.


Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.


If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Motor is running and the brush is also running but i have no suction and the suction tube is clear


A clogged filter or if it has a bag hole in bag or bag isn't in correct. ... Hoover Vacuums

Brand new LG LUV200r used 10 minutes now after removing dust tank & reinstalling the vacuum motor does not run only the beater bar??? I have located wo circuit breakers both seam to be set. This suction motor should run when the switch is pressed & the beater bar should operate when the handle is moved down??? Not A happy customer will return unit to Best Buy only 100 mile round trip!!!! RDH


... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

My dyson DC07 has no suction. motor runs, brush spins, just no suction.


Hi..the reason to this problem may be the bottom pieces \015\012might not have been fully seated.Take it apart and put it \015\012carefully back together.This will solve the issue.\015\012check it out..\015\012thank u..\ ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I have a Bissell proheat2 turbo carpet cleaner. The power brushes have stopped rotating. The brushes are free to turn by hand . The motor works fine with good suction. What is the problem ?


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Motor not running but brushes rotate, makes weird sound


Thats decouse it is,,,it could well have burnt out if it got "cooked" becouse it was blocked up with dogy hair they get very hot and just melt? ... Dyson DC25 All Floors Bagless Upright Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Motor runs brushes but no suction - Vacuums


Blockage? ... Vacuums

Motor is running, belt is on and brush is turing fast, however it does not seem to pick-up anything or have any suction ? bag is not full and does not inflate when it's on


... Dirt Devil M086365 Bagged Upright Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

Took my Hoover Steam Vac apart to clean it and now it won't **** up the water but was working fine before I got the bright idea to clean it. Took four screws out but did not touch the motor. It puts out water and the brushes rotate but no suction? Thank you for your help, Cathy


The suction is created by the motor and is pulled to the motor through the flexible hose. The hose could have pulled off at one end or it could have torn in a spot where there is more pull on the hose like when you lay the handle down to empty dirty ... Hoover F7431-900 SteamVac Vacuum

Has a Bissell, Pro Heat 2X rug shampooer. It powers up & and the motor runs but the brushes are not rotating and water is not being dispensed.


Brush roller not working and water not dispensing was mostly caused by a brush belt being broken or is out of place.Turn the machine off and unplug it if the Brush roller do \015\012not turn. Remove any objects caught in the brush roll. A ... Vacuums

Doesn't suck I have a Hoover Empower. The motor runs, but it is not sucking anything up and the brushes aren't rotating.


Every vacuum needs to be occasionly taken apart and throughly cleaned. Usually when the brushes don't rotae it's a belt. But sometimes it's because junk gets wrapped around the roller. Things like string or thread or fiber that wounds around the r ... Kenmore 35912 / 35913 Progressive Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0715 seconds