Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?

The spinning brushes mechanism won't spin. May have stopped working correctly after I emptied canister - not sure. Thanks.


Answers :

\015\012With the machine switched off, press the re-set switch on the side of the head, making sure you push the button in as far as you can. When you switch the machine back on and lower it into the vacuuming position, the brush bar should start turning. --------The brushes don't spin if the unit is placed upright.\015\012First off check that you haven't pressed the button that turns the brush on and off.--\015\012But if that is turned ON.Then the other possibility can be clogged brush with dirt.\015\012take a look at the brush bar to see how much hair and debris is caught in there. If there is very little then you probably don't have much to worry about and you can press the brush reset bar on the side of the vacuums head and your problem with they Dyson brush not turning can be fixed.\015\012Also check the be belt and the motor.If belt is got loose, then motor will spin but brush will not spin, due to loose or worn out belt.If belt is intact, but motor is not spinning, then its weak motor issue.If motor is the issue, then to replace and repair the motor.Please click the link below:----\015\012http://dysonmedic.co.uk/dyson-dc24-brush-bar-motor/\015\012-------------\015\012The operating instruction for dc-24 and dc-25 are near to same.So if you require disassembly instructions.Please click this link below and see the video.This will help, for disassembly:---\015\012http://www.videojug.com/film/loss-of-suction-dyson-dc25\015\012----------------\015\012This should help, thanks.Helpmech.
Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The spinning brushes mechanism won't spin. May have stopped working correctly after I emptied canister - not sure. Thanks.


\015\012With the machine switched off, press the re-set switch on the side of the head, making sure you push the button in as far as you can. When you switch the machine back on and lower it into the vacuuming position, the brush ba ... Dyson Ball DC24 Bagless Upright Vacuum

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

Vacuum stops My Wind Tunnel stops working in a very short time when using. It takes awhile for it turn back on. It still shuts off quick. I have cleaned the hoses and inside of the power brush. This doesn't correct problem. Delbert Briggs


Your thermal cutout is tripping. This only happens when the motor heat gets very high, and the reason it takes a while to turn back on is that the motor has to cool down before it will reset. Ensure that absolutely every air pathway is clear, because ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Stopped working new item given as a gift, used once, in the middle of cleaning then died. Did as manual stated for over heating, empty canister, clean all filters and allow to cool for an hour. Left over night, tried the next day but does'nt work???? What can i do???


... Vacuums

Roomba Discovery My Roomba Discovery seems to work fine, mechanically, but it no longer seems to collect any dust. (The collection bin remains empty after the Roomba has circulated around the floor for quite a while). The brush has been replaced and spins normally. Does anyone have an idea why this machine's vacuum function no longer seems to work? I would appreciate any feedback. Jeremy


Did you replace the filter? when you remove the dust bin there is a small filter that needs to be cleaned, or replaced. You can buy a maintenance kit that replaces the brushes and filters as well, its good to replace them all regularly ... Roomba Robotic Floor Bagless Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?


I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

I have an Electrolux EL 6988 type E Oxygan Bagged Canister vacuum brush roller in not working. I took off the stuff that was stopping to rooler from working and now I can't get the roller to move.


... Electrolux EL7024A Oxygen3 Bagged Canister Vacuum

I have the same problem as discussed above. My Hoover Pet Cyclonic upright stops working while using it. The bottom feels hot when this happens. When it first occurred, I emptied the canister and even tried a different plug. It did not turn back on for over an hour. When it did turn back on, it would die again after about 3-5 minutes of use. I don't know what else to try. I have washed the secondary filters, let them air dry and replaced them and this did not help the problem. My friend,


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

The rotating brush at my new bissel vacuum doesn't work. The belt is OK, the canister is empty and clicked into position, no clog???


... Bissell 3750 Lift Off Bagless Upright Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

Bissell Big Green Machine just stopped working in mid-clean. Have emptied tank, rinsed tank, checked belt, checked brush and still nothing. Have even changed outlets. Suggestions?


The motor could have fried or the wires have been shaken off the motor terminals. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

I had to empty the canister and when I put it back on and turned on the vacuum, the suction does not turn on. The brushes are rolling and the attachment suction works fine. Any suggestions?


... Eureka 431A Optima Bagless Upright Vacuum

My Hoover Pet Cyclonic upright stopped working while I was using it. The bottom felt really hot so I emptied the canister & laid the vacuum down with the bottom in the air to cool off & went back in an hour or so, I even tried a different plug in but it still won't turn back on. I don't know what else to try.


This just happened to me. Any solutions or insights? I need to know asap. ... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?


Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums

I have a canister style vacuum. The brush roll has stopped rolling on carpet. When turned over, it rolls fine. I have disassembled and cleaned out hair and that didn't work. Any help would be very much appreciated. Thank you. Martha


You need a new belt. They stretch after awhile and won't turn the brush roll under load. ... Vacuums

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.


... Windsor VS14 Versamatic Bagged Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


You need to change the belt(s). You can find the belts for this model here. http://www.vacbelts.com/bissell-proheat-belt-combo-pack.htm ... Bissell 8910 ProHeat Clear View Upright Vacuum

My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920


The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

The head on my Hoover Canister vacuum has stopped working


It sounds like the power connection pins, from the handle tube to the powerhead, are not making connection. The pins could have been damaged when you impacted it. ... Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1332 seconds