Having problems with your Dyson Ball DC24 Bagless Upright Vacuum ?

Dyson ball DC24 when you put the handle in the tube the handle goes toofar and pushes the bottom open


Answers :

Hi there,

I can confirm that what you've noticed is part of the valve mechanism, which switches the airflow from the hose to the cleaner head when you replace the wand on the machine. This is a normal feature of the DC24, and nothing to worry about.

If you have any further questions about using or maintaining your machine, please visit www.dyson.com and click 'Support', or call our customer Helpline on 0800 298 0298 (UK), or 1-866-693-9766 (US).

Best wishes,

Jack
Dyson Online Customer Support
http://www.dyson.com
Repair Help & Product Troubleshooting for Dyson Ball DC24 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson ball DC24 when you put the handle in the tube the handle goes toofar and pushes the bottom open


Hi there,I can confirm that what you've noticed is part of the valve mechanism, which switches the airflow from the hose to the cleaner head when you replace the wand on the machine. This is a normal feature of the DC24, and nothing to worry ... Dyson Ball DC24 Bagless Upright Vacuum

Brushes won't turn on the bissell proheat 2X steam cleaner-I don't have the manual to see if there is a button I am not pushing to turn on the brushes. Also, do you put the clean water in the "bladder" in the tank? Sorry I am so dumb-this cleaner was given to me with no manual and I can't figure it out. There is a small tank on the bottom at the back of the machine, that says "formula here" and I don't know if that is where the cleaner goes or what that is for. The machine turns on just fine


... Bissell 8910 ProHeat Clear View Upright Vacuum

I am putting my bissel 8910 back together and behind the motor there is a black 3-way tubing connector. One side goes to the pump discharge, one side goes to a tubing going to the right rear wheel (facing the unit from the front) I don't know where the third side goes to. I do not seem to have another tubing for this one to go to? Maybe it is lost or ?


Hi, its hard to know what its for without seeing it. The best way to test this is to start the machine and vacuum a part of the carpet/ floor. Then let me know wht the vacuum is not doing. This will narrow it down. Please, get back to me. This sounds ... Bissell 8910 ProHeat Clear View Upright Vacuum

No suction at floor brush. Plenty of suction in the tube that goes to the joint just before the 90 degree turn to go from the handle to the brush area.I lowered the handle so that the tube was straight and probed. The tub is clear. I cann't find the manual at home or on line. The Hoover.com site is useless in searching for a manual.


Are you sure the brush roll is turning. If not sometimes it will appear to not be sucking. Take off the bottom plate, then you can get to the brush roll and belt.\015\012 ... Hoover 5416-900 WindTunnel Bagged Upright Vacuum

Need instructions how to use Hoover Steam Vac Spin Scrub. I borrowed it from my Sister and she left it with no instruction book or letting me know how to operate it. I put water & cleaner in top tank. That's all I know to do. Do I put any water in bottom tank? I figured not, since that is probably where the water goes when sucked up by vac. Do I leave lid on bottom tank? I usually use a commercial cleaner, and this is very different. I need to know NOW, as I must return it to her today, and I'm


I did have a solution in just a few minutes. Someone responded with a solution that gave me the website where I could go and print the manual in pdf, so did that, and checking instructions I was able to clean my carpets and get the shampooer back to ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Hoover Mach 6 U5198-900 vacuum roller brush won't turn. I had opened the bottom to clean hair off the roller. the belts are not broken. When I closed it and turned it on, now the roller brush won't turn. I can push and turn it by hand, but not easily. Then I noticed the brush on/off switch is turned off, but when I step on it, it won't turn on. I was thinking I let something get out of place when I opened the bottom, but can't see what.


... Hoover Tempo Widepath Upright Vacuum - Blue

My cigarette injector nozzle on my Top-O-Matic keeps coming off. Why and how do I fix it? With glue? I put the tobacco in, and my empty cigarette tube on the nozzle, then use the hand crank to push the tobacco into the tube and the NOZZLE is coming off with the tube and the tobacco isn't filling the tubes. please email me back a response [email protected]


... Hoover H3030 FloorMate SpinScrub 500 Upright Wet/Dry Vacuum

My 8 yr old kenmore vacuum works well - however the hose has worn under the handle where there is a hole (resulting in decreased suction power). I'd like instructions on opening the handle and bypassing the worn piece of tubing rather than replacing it for $129. Some of the handle screws remove easily but the last one doesn't loosen easily.


Hi,Have you tried spraying the stubborn screw with WD40 and let it soaked for a while? Other than these screws holding the handle together, there would no other way of opening it up. Hope this be of initial help/idea. ... Kenmore Vacuums

Im trying to put the peice back together that goes under the tube that hold the water the part that goes into the hole in the vacum.. i took it apart because its not spraing right to see if it was cloged.. and now im not sure how it goes back together.. can you please help me.....


I tried to find a service manual for this, but came up with only a exploded view diagram:\015\012\015\012http://ineedbags.com/images/b8920.jpg\015\0 ... Bissell 8920 ProHeat 2XTM Upright Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Flotec shallow well FP4122-08. A burglar stood on the pump this summer to gain access to my goats building (window). There's a small black tube that came off at both ends. When I put the tube back on, it shoots right back off as soon as the pump is plugged in. I don't know the name of the part (tube) to order a new one, and I don't know if it just plugs onto the fittings of both ends, or goes into the pump at the end with the round fitting on it.


... Vacuums

My Dyson DC14 Animal doesn't have the suction it used to. The piece in the back on the bottom - a flap it appears - stays open now, causing the machine to make a louder noise than usual. At first, if I put my hand on the flap opening it would close, allowing for normal suction. Now, it stays "open" permanently", causing the loss of suction.


Hi its Darran at Dyson.Having had a look at a DC14 here, I am unsure as to the part you are referring to. So that we can help you further, please contact our Helpline free on 0800 298 0298, between the hours of 7am - 10pm, 7 days a week. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Trouble opening tank, pushing handle and it wont open


Push down on the handle while lifting the right side of the tank with your other hand. ... iRobot 5800 Scooba Vacuum

I removed the handle of my Dyson DC24 to vaccum in high areas and now when i try to put the back piece back, it doesn't click. So when try to vaccum on the floor the handle just comes off.


Hi there,I'm sorry to hear you're having difficulty with your DC24. The wand handle should reattach easily to the machine, locking into place with an audible 'click'. If it doesn't seem to be doing this, you may want to check you have the han ... Dyson Ball DC24 Bagless Upright Vacuum

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.


... Panasonic Kenmore Canister Vacuum Vacuum

Kirby Seems like you know alot about the Kirby. I know how to use my Sentria (unlike these other idiots) but I keep screwing up the shampoo tray assembly. The brush snaps into the tray just fine but the tray doesn't really stick to the head. It detaches when pushing and pulling the unit. And who knows where that cover goes? It say 'push here to open'


Machine will not come on ... Kirby G6 Bagged Upright Vacuum

My Bissel proheat carpet cleaner wont spray out of the bottom or the spray handle. I took of the scrub brushes and off and cleaned out the bottom of the machine including popping out the two spray heads to make sure they were not clogged. Put it back together. Still no spray! I also did the turn off, remove fluid containers, replace, turn on for one minute to prime the pump, and still so spray...does this mean my pump is not working?


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.


You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?


If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum

I have a bissell quickwash 1950-e. I bought it Jan. 2006, and have only used it 8-10 times, I live in a very hard water area, so I though if I put some vinegar in with the cleaning solution it would get rid of any hard water deposits, unfortunatly the solution went lumpy in the tank and stoped spraying out water, I have opened it, hose clean, sprayer not blocked, x at bottom of water container when depresed water trickles out, component that opens the x when water container placed, also ran wate


Hard to say what is causing your problem, replacing the cap and insert on the water tank may help, part #2041111, even tho it may trickle out water when depressed, they can still be bad. The other thing would be the rod not relesing the water like i ... Vacuums

My Dyson DC24 sucked in a backpack strap and tripped. I then decided to pull out the brush and clean off whatever else happened to be clung onto it and put it back in. The darn thing doesn't turn anymore. Everyone says to push the reset button in until a click is heard but I put in a bit of force and I haven't heard a click so I stopped because I didn't want to break it. Is there something I haven't checked or do I keep adding force?


If the motor is running and the roller is not turning you may have to let the handle down as you would when you are getting ready to vacuum the flood. I think there is a switch you step on to let the handle down and it will engage the roller bar moto ... Dyson Ball DC24 Bagless Upright Vacuum

Doesn't work Our home was built and finished in August 07.  The central vac doesn't work.  There is supposed to be a slot that opens in the kitchen where you sweep the dust and it sucks it up.  Also, the mounted unit on the garage wall has a hose that goes up into the house but there is a hole open at the bottom of the unit.  Where can I get someone to help us?  Or, is there an installation manual I can download to see if the builder did it properly.  He stole our solar heater for our pool and s


Has the slot in the kitchen (VacPan) been installed? Or is it just not working? There should be tubing coming into the unit in the garage, and possibly another piece to exhaust the unit to the outdoors, although this isn't always necessary. The intak ... Electrolux Centralux Vacuum

Small metal rod fell out when i opened the bottom of the orecl xl 21. where does it goes?


Sounds like the roller axle ... Oreck XL21 Bagged Upright Vacuum

How to open the bottom of my WP-72W to change the handle


... Vacuums

Hi I have a eureka 410 series lightweight upright and I took it apart to clean the dust from inside and on the very bottom of the handle the is a metal clip and a white straight plastic peice that fell out and I dont know how it goes back in.


... Eureka Whirlwind 410 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0998 seconds